Teknik Hudson 5425825 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Hudson Beside Night Stand
Model 5425825
It stands. You sleep.
Teknik
www.teknikoffice.co.uk

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
Skip the power trip.
This time.
3
4
5-15
16-18
19-21
22
23
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT END (1)
B RIGHT END (1)
C BOTTOM (1)
D TOP (1)
E SHELF (1)
F SKIRT (1)
G DRAWER FRONT (1)
H LEFT DRAWER SIDE (1)
J DRAWER BACK (1)
K DRAWER BOTTOM (1)
L BACK (1)
M RIGHT DRAWER SIDE (1)
Page 3
A
B
C
D
E
F
G
H
J
K
L
M

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
SILVER 1-1/2" FLAT HEAD SCREW - 4
10
SMALL WOOD
DOWEL - 8
8
LARGE WOOD
DOWEL - 20
7APPLIQUE - 10 9
FILE GLIDE - 2
3
(EXTENSION SET SHOWN SEPARATED)
CAM SCREW - 22
6
LARGE HIDDEN
CAM - 18
4SMALL HIDDEN
CAM - 4
5
SILVER 3/8" FLAT HEAD SCREW - 10
11
1EXTENSION RAIL - 2 2EXTENSION SLIDE - 2

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 5

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to avoid
scratching your unit or the floor.
å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as
shown in the upper diagram below. Be prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (1) to the ENDS (A and B). Use six SILVER
3/8" FLAT HEAD SCREWS (11) in the exact holes shown in the upper
diagram below.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in
the enlarged diagram. Then, slide the inner cartridge of the EXTENSION
RAIL in to find the other holes that line up with the holes in the END.
Turn a SCREW into these holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWER.
Page 6
A
B
12
Open end
Open end
Push the release lever up or down and pull the SLIDE from the RAIL.
1
1
Edge with
more holes
These holes
must be here.
These holes
must be here.
SILVER 3/8" FLAT HEAD SCREW
(6 used for the RAILS)
11

Step 2
Page 7
å Push four LARGE HIDDEN CAMS (4) into the ENDS (A and B).
å Turn fourteen CAM SCREWS (6) into the exact holes shown in
the ENDS (A and B).
å Then, insert fourteen LARGE WOOD DOWELS (7) into the
remaining holes in the ENDS (A and B).
A
B
Arrow
4
6
7
(14 used)
Just think. The sooner
you do this, the sooner
you do something else.

å Push four LARGE HIDDEN CAMS (4) into the BACK (L).
å Fasten the BACK (L) to the LEFT END (A). Tighten two
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LEFT END
insert into the BACK.
Step 3
Page 8
Notch
L
A
L
Surface with
HIDDEN CAMS
Edge with
HIDDEN CAMS
Arrow
4
Arrow
4
The EXTENSION RAIL
is closer to this edge.

å Push eight LARGE HIDDEN CAMS (4) into the
BOTTOM (C) and SHELF (E).
å Fasten the BOTTOM (C) and SHELF (E) to the LEFT
END (A). Tighten four HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LEFT END
insert into the BOTTOM and SHELF.
Step 4
Page 9
E
A
C
C
Arrow
4
Arrow
4
Surface with
HIDDEN CAMS
E
Surface with
HIDDEN CAMS
Finished edge
Finished edge

Step 5
Page 10
å Push two LARGE HIDDEN CAMS (4) into the SKIRT (F).
å Fasten the SKIRT (F) to the LEFT END (A). Tighten one
HIDDEN CAM.
å NOTE: Be sure the WOOD DOWEL in the LEFT END inserts
into the SKIRT.
å Fasten the RIGHT END (B) to the BOTTOM (C), SHELF (E),
SKIRT (F), and BACK (L). Tighten seven HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the RIGHT END
insert into the BOTTOM, SHELF, SKIRT, and BACK.
B
A
Surface without
HIDDEN CAMS
Arrow
4
Arrow
4
F
E
C
F
Surface without
HIDDEN CAMS
L