Teknik 5412314 User manual

NOTE
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
www.sa.com Corner Computer Desk
5412314
Assembly Instructions
Teknik
www.teknikoffice.co.uk

PARTS IDENTIFICATION
While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help
While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help
distinguish similar parts from each other. Use this
distinguish similar parts from each other. Use this
PARTS IDENTIFICATION
PARTS IDENTIFICATION
to help identify similar parts.
to help identify similar parts.
ITEM DESCRIPTION QTY
A END 2
B RIGHT UPRIGHT 1
C LEFT UPRIGHT 1
D TOP 1
E SHELF 2
F BACK 2
G RIGHT FRONT LEG 1
H LEFT FRONT LEG 1
I RIGHT REAR LEG 1
J LEFT REAR LEG 1
K KEYBOARD FRONT 1
L KEYBOARD BACK 1
M KEYBOARD SIDE 2
N KEYBOARD SHELF 1
O DRAWER UPRIGHT 2
P SHELF MOLDING 2
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
AF
E
M
O
P

HARDWARE IDENTIFICATION
HIDDEN CAM - 31 CAM SCREW - 16 CAM DOWEL - 15
HINGE - 2 KNOB - 1 CAM COVER - 4
U2 V2 W2
X Y Z
35GA CABINET RIGHT - 1 35GB CABINET LEFT - 1
35GC DRAWER RIGHT - 1 35GD DRAWER LEFT - 1

SCREWS SHOWN ACTUAL SIZE
SCREWS SHOWN ACTUAL SIZE
Using a SCREW that is too long will caus
Using a SCREW that is too long will caus
e
e
d
d
a
a
mage. Before beginning assembly, separate
mage. Before beginning assembly, separate
each type of SCREW. Carefully study the SCREW diagrams below
each type of SCREW. Carefully study the SCREW diagrams below
(
(SHOWN ACTUAL SIZE
)
)
.
.
Pay close attention to the color of each SCREW. You may receive extra hardware with your unit.
Pay close attention to the color of each SCREW. You may receive extra hardware with your unit.
HAMMER
1
TIP SHOWN ACTUAL SIZE
NO. 2 PHILLIPS SCREWDRIVER
ASSEMBLY TOOLS REQUIRED
GG
BLACK 1-7/8” FLAT HEAD SCREW - 8 BROWN 1-1/2” FLAT HEAD SCREW - 4
GOLD 5/16” FLAT HEAD SCREW - 8
BLACK 1-1/4” FLAT HEAD SCREW - 2 BLACK 7/8” MACHINE SCREW - 1
SILVER 5/8” FLAT HEAD SCREW - 4 SILVER 9/16” LARGE HEAD SCREW - 2
AA BB
CC DD
EE FF

2
 Push thirty-one HIDDEN CAMS (U2) into the ENDS (A), UPRIGHTS (B and C), SHELVES (E), BACKS (F), DRAWER
UPRIGHTS (O), and SHELF MOLDINGS (P). Then insert the metal end of fifteen CAM DOWELS (W2) into the HIDDEN CAMS. 
(15 used)
Arrow
Do not tighten the HIDDEN CAMS in this step.
Arrow
Arrow
Arrow
B
C
O
O
U2
W2
(31 used)
E
F
F
E
P
Do not insert CAM
DOWELS into these parts.
Do not insert CAM DOWELS
into these HIDDEN CAMS.
A
U2
U2

3
(16 used)
Turn sixteen CAM SCREWS (V2) into the LEGS (G, H, I, and J).
G
H
I
J
V2
V2

4
Fasten the CABINET RIGHT (35GA) and CABINET LEFT (35GB) to the DRAWER UPRIGHTS (O). Use four GOLD
5/16” FLAT HEAD SCREWS (GG) through holes #1 and #3.
1
2
3
1
2
3
Roller End
Roller End
O
O
GOLD 5/16” FLAT HEAD SCREW
(4 used in this step)
GG
Use second hole

5
Edge with CAM
DOWELS
Fasten the LEGS (G, H, I, and J) to the ENDS (A) and SHELF MOLDINGS (P). Tighten eight HIDDEN CAMS.
A
P
A
P
G
H
I
J
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Edge with CAM
DOWELS

6
G
H
I
J
E
F
F
E
Fasten the SHELVES (E) and BACKS (F) to the LEGS (G, H, I, and J). Tighten eight HIDDEN CAMS.
Unfinished
surface
Unfinished
surface
Surface with
HIDDEN CAMS

7
Fasten the LEFT UPRIGHT (C) to the RIGHT UPRIGHT (B). Tighten three HIDDEN CAMS.
B
C
Unfinished
surface
Unfinished
surface
Finished
edge
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Arrow
Maximum
210 degrees
Minimum
190 degrees