Teknik Streamline L-Shaped Desk 5414417 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Streamline L-Shaped Desk
|Model 5414417
www.teknikoffice.co.uk
For all your
newfangled gadgetry.
Teknik

Table of Contents Assembly Tools Required
2-3
4
5-22
29-30
31
Part Identification
Hardware Identification
Assembly Steps
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Page 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A LOWER END (1)
B HUTCH END (2)
C UPRIGHT (1)
D CENTER UPRIGHT (1)
E HUTCH UPRIGHT (2)
F2 LOWER TOP (1)
G HUTCH TOP (1)
H2 TOP (1)
I HUTCH BOTTOM (1)
J SHELF (1)
K BOTTOM (1)
L DESK BACK (1)
M LOWER BACK (1)
N HUTCH BACK (1)
O FLIP DOWN DOOR (1)
P DRAWER FRONT (1)
Q DRAWER BACK (1)
R RIGHT DRAWER SIDE (1)
S LEFT DRAWER SIDE (1)
T DRAWER BOTTOM (1)
U DIVIDER (1)
V DESK FRAME (2)
W RETURN FRAME (2)
X UPPER MOLDING (1)
Y LOWER MOLDING (1)

Part Identification Now you know
our ABCs.
Page 3
A
B
C
D
E
F2
G
H2
I
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
B
E
W
V
J
K

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
PULL - 1
21K
BLACK 1-7/8" FLAT HEAD SCREW - 18
2S
BLACK 9/16" LARGE HEAD SCREW - 20
1S
HIDDEN CAM - 19
1F CAM DOWEL - 19 2F
NAIL - 28
1N METAL PIN - 4 1R
PIVOT HINGE - 6
15H WASHER - 2 9I
STRIKE PLATE - 1
6I
BLACK 1/2" FLAT HEAD SCREW - 3
11S
MAGNETIC CATCH - 1
2I
BLACK 3/4" PAN HEAD SCREW - 12
85S BLACK 3/4" PAN HEAD SCREW (with flat end) - 2 90S
3S GOLD 5/16" FLAT HEAD SCREW - 8
(EXTENSION SET SHOWN SEPARATED)
EXTENSION RAIL - 2
35MA EXTENSION SLIDE - 2 35MC

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push nineteen HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHTS (C and D), LOWER TOP (F2), DESK BACK (L),
and DRAWER SIDES (R and S). Then, insert the metal end
of a CAM DOWEL (2F) into each HIDDEN CAM.
Page 5
R
S
B
B
F2
A
L
C
D
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
(19 used)
Meet Part (F2). This component has
been engineered to be lighter, stronger,
faster… well ok. Not technically faster.
But definitely makes for a sturdier L
Desk that’s easier to assemble and
friendlier to the environment.

Step 2
å Separate the EXTENSION SLIDES (35MC) from the
EXTENSION RAILS (35MA) as shown in the upper
diagram below. Be prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (35MA) to the LOWER
END (A) and CENTER UPRIGHT (D). Use four GOLD 5/16"
FLAT HEAD SCREWS (3S) through holes #1 and #3.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the
hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL in to find the other hole
that lines up with the hole in the END and UPRIGHT. Turn
a SCREW into this hole.
Page 6
A
D
Surface with
HIDDEN CAMS Surface without
HIDDEN CAMS
1
2
3
3
2
1
Remember:
Righty tighty.
Lefty loosey.
Finished edge
Finished edge
Open end
Open end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Push the black lever in and pull the SLIDE from the RAIL.
35MA
35MC

å Fasten the HUTCH ENDS (B) to the HUTCH TOP (G).
Tighten four HIDDEN CAMS.
Step 3
Page 7
B
B
G
Surface with holes
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Surface with
HIDDEN CAMS
Long finished edge
Surface with
HIDDEN CAMS
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

Step 4
å Fasten the HUTCH UPRIGHTS (E) to the HUTCH BOTTOM (I).
Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
å Fasten the HUTCH BOTTOM (I) to the HUTCH ENDS (B). Use
four BLACK 1-7/8" FLAT HEAD SCREWS (2S).
414417 www.sauder.com/servicesPage 8
B
B
E
E
I
Surface with
more holes
Finished edge
Long finished edge
Finished edge
Edge with holes
BLACK 1-7/8" FLAT HEAD SCREW
(8 used in this step)
2S

å Carefully turn your unit over onto its front edges. Lay the
HUTCH BACK (N) over your unit.
å Make equal margins along all four edges of the HUTCH
BACK (N). Push on opposite corners of your unit if needed to
make it "square".
å Fasten the HUTCH BACK (N) to your unit using the NAILS (1N).
Step 5
Page 9
N
NAIL
(28 used in this step)
1N
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

Step 6
å Carefully turn your unit over onto its back.
å Fasten the DESK FRAMES (V) to the HUTCH BOTTOM (I).
Use four BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: The UPPER MOLDING (X) will have more holes than
the LOWER MOLDING (Y). Do not confuse these MOLDINGS.
å Fasten the UPPER MOLDING (X) to the HUTCH BOTTOM (I).
Use four BLACK 9/16" LARGE HEAD SCREWS (1S).
Page 10
I
X
V
V
The UPPER MOLDING (X) will have more
holes than the LOWER MOLDING (Y).
Long edge
BLACK 9/16" LARGE HEAD SCREW
(8 used in this step)
1S