Teknik City Centre 5427120 User manual

City Centre Desk
Model 5427120
For all your
newfangled gadgetry.
Teknik
www.teknikoffice.co.uk

No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
2
3
4-12
13-14
15-16
17-18
19
Hardware Identification
Part Identification
Assembly Steps
Français
Español
Safety
Warranty
åScrews are shown actual size. You may receive extra hardware with your unit.
Hardware Identification
L-WRENCH - 1
1
25/16" HEX HEAD SCREW - 12 313/16" HEX HEAD SCREW - 12
43/8" PAN HEAD SCREW - 24
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A REAR LEFT LEG (1)
B FRONT LEFT LEG (1)
C LEFT MOLDING (1)
D REAR CENTER LEG (1)
E FRONT CENTER LEG (1)
F RIGHT MOLDING (1)
G CENTER MOLDING (1)
H TOP (1)
J SHELF (3)
K RIGHT LEG (2)
A
B
C
D
E
F
G
H
J
K
J
J
K
Page 3

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to
avoid scratching your unit or the floor.
å Fasten the LEFT LEGS (A and B) to the LEFT MOLDING (C). Tighten
four 5/16" HEX HEAD SCREWS (2) using the L-WRENCH (1).
å NOTE: You should start each SCREW a few turns before completely
tightening any of them.
A
B
C
1
5/16" HEX HEAD SCREW
(4 used in this step)
2
Page 4
Just think. The sooner
you do this, the sooner
you do something else.

å Fasten the CENTER LEGS (D and E) to the
RIGHT MOLDING (F). Tighten four 5/16" HEX
HEAD SCREWS (2) using the L-WRENCH (1).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 2
D
E
F
1
5/16" HEX HEAD SCREW
(4 used in this step)
2
Page 5

å Fasten the MOLDINGS (C and F) to the CENTER MOLDING (G).
Tighten four 5/16" HEX HEAD SCREWS (2) using the L-WRENCH (1).
å NOTE: You should start each SCREW a few turns before completely
tightening any of them.
Step 3
A
C
F
G
D
1
5/16" HEX HEAD SCREW
(4 used in this step)
2
Page 6

å Fasten the LEGS (A, B, D, and E) to the TOP (H). Tighten eight
13/16" HEX HEAD SCREWS (3) using the L-WRENCH (1).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 4
H
A
D
B
E
1
Page 7
13/16" HEX HEAD SCREW
(8 used in this step)
3
Now might be a
good time to refresh
your drink.

å Fasten the RIGHT LEGS (K) to the TOP (H). Tighten four
13/16" HEX HEAD SCREWS (3) using the L-WRENCH (1).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 5
H
K
K
1
13/16" HEX HEAD SCREW
(4 used in this step)
3
Page 8

å Fasten a SHELF (J) to the LEGS (D, E, and K). Use eight
3/8" PAN HEAD SCREWS (4).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 6
3/8" PAN HEAD SCREW
(8 used in this step)
4
K
K
D
E
J
Page 9

å Fasten a SHELF (J) to the LEGS (D, E, and K). Use eight
3/8" PAN HEAD SCREWS (4).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 7
K
K
D
E
J
Page 10
3/8" PAN HEAD SCREW
(8 used in this step)
4