Teknik Hampstead Park Narrow Bookcase 5420283 User manual

www.teknikoffice.co.uk
Narrow Bookcase
Hampstead Park Collection | Model 5420283
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
The stories of your life.
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-23
24-27
28-31
32-34
35
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP MOLDING (1)
D TOP (1)
E SMALL SHELF (1)
F SHELF (1)
G LARGE SHELF (1)
H BRACE (1)
I BOTTOM (1)
J RIGHT FRONT/LEFT REAR FOOT (2)
K LEFT FRONT/RIGHT REAR FOOT (2)
L BOTTOM BRACE (2)
M LEFT DRAWER SIDE (2)
N DRAWER BACK (2)
O RIGHT DRAWER SIDE (2)
P DRAWER BOTTOM (2)
Q DRAWER BRACE (2)
R DRAWER FRONT (2)
S BACK (1)
AB
C
D
E
F
G
H
I
L
R
S
MN
O
P
R
J
L
K
Q
MN
O
P
Q
Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
EXTENSION SET SHOWN SEPARATED
1EXTENSION RAIL - 4 2EXTENSION SLIDE - 4 3LARGE HIDDEN CAM 36 4SMALL HIDDEN CAM  12
Anled head Straiht head
5ANGLED HEAD
CAM SCREW  36 6STRAIGHT HEAD CAM SCREW  12 7LONG WOOD
DOWEL  30 8SHORT WOOD DOWEL  4 9COVER CARD  1
10 KNOB  2 11 LONG FILE
GLIDE - 2 12 SHORT FILE GLIDE - 4 13 FRONT FILE GLIDE  2 14 FILE HANGER  4
19 BLACK 112" FLAT HEAD SCREW  12
20 BLACK 118" FLAT HEAD SCREW  3 21 BLACK 78" MACHINE SCREW  2
22 BLACK 12" PAN HEAD SCREW  32 99 FURNITURE TIPPING
RESTRAINT KIT  1
17 NAIL  50
Pae 4

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Fasten the TOP MOLDING (C) to the TOP (D). Use three
BLACK 1-1/8" FLAT HEAD SCREWS (20).
å Insert eiht LONG WOOD DOWELS (7) into the exact
holes shown in the short edes of the TOP (D) and
SMALL SHELF (E).
E
D
7
7
7
7
Rounded ede
Rounded ede
C
BLACK 118" FLAT HEAD SCREW
(3 used in this step)
20
Pae 5

å Insert eiht LONG WOOD DOWELS (7) into
the exact holes shown in the short edes of the
SHELVES (F and G).
Step 2
7
7
7
7
Rounded ede
Rounded ede
F
G
Pae 6
Some assembly
(and snacks) required.

å Turn eiht ANGLED CAM SCREWS (5) into the small
holes in the BOTTOM (I).
å Insert four LONG WOOD DOWELS (7) into the edes of
the BOTTOM (I).
Step 3
Finished ede
7
7
5
Anled head
I
Pae 7

å Turn two ANGLED HEAD CAM SCREWS (5) into the
FEET (J and K).
å Insert two LONG WOOD DOWELS (7) into the FEET (J and K)
and one into the lon ede of the BOTTOM BRACE (L).
å Insert two LARGE HIDDEN CAMS (3) into the holes in the
BOTTOM BRACE (L) as shown.
å Fasten the FEET (J and K) to the BOTTOM BRACE (L).
Tihten two LARGE HIDDEN CAMS.
å Repeat this step for the other FEET (J and K) and
BOTTOM BRACE (L).
Step 4
Anled head
J
K
L
5
5
3
7
7
7
321
The arrow must
point toward the
ede of the board.
3
Pae 8

å Insert four LONG WOOD DOWELS (7) into the BOTTOM (I).
å Insert eiht LARGE HIDDEN CAMS (3) completely into the
holes in the BOTTOM BRACE (L) and FEET (J and K) as shown.
å Fasten the FEET (J and K) and BOTTOM BRACES (L) to the
BOTTOM (I). Tihten eiht LARGE HIDDEN CAMS.
Step 5
Anled head
321
The arrow must
point toward the
ede of the board.
3
J
K
L
J
K
L
3
7
7
7
7
33
I
Pae 9

å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the diaram. Be
prepared; the parts are reasy.
å Fasten two EXTENSION RAILS (1) to the LEFT END (B). Use six BLACK 1/2" PAN HEAD SCREWS (22).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the holes shown in the diaram. Then, slide the
inner cartride of the EXTENSION RAIL in to find the other two holes that line up with the holes in the
LEFT END. Turn the SCREWS into those holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
å Turn twelve ANGLED HEAD CAM SCREWS (5) into the LEFT END (B).
Step 6
Use these holes.
Push the black lever down and
pull the SLIDE from the RAIL.
Anled ede
Open end
Open end
Anled head
B
1
1
5
12
BLACK 12" PAN HEAD SCREW
(6 used in this step)
22
Pae 10