Teknik 5414873 User manual

Tidy up. Cruise around.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Sewing/Craft Cart
Model 5414873
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-18
19-21
22-25
26
27
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C2 UPRIGHT (1)
D TOP (1)
E FLIP-UP TOP (1)
F BOTTOM (1)
G2 MODESTY PANEL (1)
H2 SHELF (1)
I ADJUSTABLE SHELF (2)
J CENTER DOOR (1)
K RIGHT DOOR (1)
L BACK (1)
MM LEFT DOOR (1)
A
B
C2
D
E
F
H2
G2
I
I
J
K
L
MM
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
HINGE - 5
16H
SLIDE CATCH - 1
6J
MAGNETIC CATCH- 2
5I
BLACK 1-1/8" PAN HEAD SCREW - 2
9S
GOLD 1" MACHINE SCREW - 3
50S
BLACK 9/16" LARGE HEAD SCREW - 40
1S
18S BROWN 1" FLAT HEAD SCREW - 2
NON- ADJUSTABLE
HINGE- 2
2H
CAM COVER - 4
19P
ADJUSTABLE HINGE - 2
3H
METAL PIN - 8
1R
BLACK 1/2" FLAT HEAD SCREW - 2
11S
NAIL - 13
1N
HIDDEN CAM - 14
1F CAM DOWEL - 14 2F
RUBBER SLEEVE - 8
2R
CASTER - 4
2CN
LOCKING CASTER - 2
2CL TRAY DIVIDER - 8
3D
TRAY - 2
2D
KNOB and BACKPLATE - 3
72K
Page 4
17E CASTER BRACKET - 6
STRIKE PLATE - 2
6I
BLACK 1-15/16" FLAT HEAD SCREW - 4
113S

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push fourteen HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHT (C2), BOTTOM (F), MODESTY PANEL (G2),
and SHELF (H2). Then, insert the metal end of a
CAM DOWEL (2F) into each HIDDEN CAM.
(14 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
C2
A
B
F
H2
G2
Page 5

Step 2
å Fasten the RIGHT END (A) to the TOP (D). Tighten
two HIDDEN CAMS.
å Fasten the BOTTOM (F) to the RIGHT END (A).
Tighten two HIDDEN CAMS.
Surface with holes
Rounded edge
Finished edge
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
A
D
F
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Page 6
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

å Fasten the UPRIGHT (C2) to the TOP (D) and BOTTOM (F).
Tighten four HIDDEN CAMS.
å Fasten the MODESTY PANEL (G2) to the UPRIGHT (C2). Use
two BLACK 1-15/16" FLAT HEAD SCREWS (113S).
å Fasten two MAGNETIC CATCHES (5I) to the UPRIGHT (C2).
Use two BLACK 1-1/8" PAN HEAD SCREWS (9S).
Step 3
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Arrow
Minimum
190 degrees
Maximum
210 degrees
C2
D
F
G2
5I
Page 7
BLACK 1-1/8" PAN HEAD SCREW
(2 used for the MAGNETIC CATCHES)
9S
BLACK 1-15/16" FLAT HEAD SCREW
(2 used in this step)
113S

å Fasten the LEFT END (B) to the TOP (D) and
MODESTY PANEL (G2). Tighten four HIDDEN CAMS.
Step 4
B
D
G2
Surface with
HIDDEN CAMS
Arrow
Minimum
190 degrees
Maximum
210 degrees
Page 8

Surface with HIDDEN CAMS
å Fasten the SHELF (H2) to the LEFT END (B). Tighten two
HIDDEN CAMS.
å Fasten the SHELF (H2) to the UPRIGHT (C2). Use two
BLACK 1-15/16" FLAT HEAD SCREWS (113S).
Step 5
Arrow
Minimum
190 degrees
Maximum
210 degrees
B
C2
H2
Page 9
BLACK 1-15/16" FLAT HEAD SCREW
(2 used in this step)
113S

Step 6
å Carefully turn your unit over onto its front edges. Lay the
BACK (L) over your unit.
å Make equal margins along all four edges of the BACK (L).
Push on opposite corners of your unit if needed to make
it "square".
å Fasten the BACK (L) to your unit using the NAILS (1N).
D
L
Finished surface
The BACK (L) should
be against the bottom
surface of the TOP (D).
These holes must be here.
Page 10
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
NAIL
(13 used in this step)
1N