Teknik 5421120 User manual

Share your journey!
www.teknikoffice.co.uk
Assembly
Instructions for
Return on Left
L-Shaped Desk
Clifton Place Collection | Model 5421120
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
2-3
4-5
6-58
59-65
66-72
73-74
75
Hammer
Not actual size
Electric drill with 3/16" bit
(ONLY in indicated step)
Now you know
our ABCs.
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Part Identification
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D RETURN UPRIGHT (1)
E TOP (1)
F RETURN TOP (1)
G SHELF (2)
H SMALL BOTTOM (1)
I BOTTOM (1)
J RETURN SMALL BOTTOM (1)
K SMALL BACK (1)
L RETURN SMALL BACK (1)
M BACK (1)
N RETURN BACK (1)
O KEYBOARD SHELF (1)
P SHORT UPRIGHT (1)
Q LONG UPRIGHT (1)
R TOP RAIL (2)
S BRACE (2)
T RETURN BRACE (1)
U SMALL DRAWER FRONT (1)
V DRAWER FRONT (2)
W LARGE DRAWER FRONT (1)
X RETURN DRAWER FRONT (1)
Y SMALL RIGHT DRAWER SIDE (1)
Z SMALL LEFT DRAWER SIDE (1)
AA SMALL DRAWER BACK (1)
BB RIGHT DRAWER SIDE (2)
CC LEFT DRAWER SIDE (2)
DD DRAWER BACK (2)
EE DRAWER BOTTOM (4)
FF LARGE DRAWER BOTTOM (1)
GG LARGE RIGHT DRAWER SIDE (1)
HH LARGE LEFT DRAWER SIDE (1)
II LARGE DRAWER BACK (2)
JJ RETURN RIGHT DRAWER SIDE (1)
KK RETURN LEFT DRAWER SIDE (1)
LL LONG BOTTOM RAIL (2)
MM BOTTOM RAIL (4)
NN FOOT (11)
OO RETURN LEFT END (1)
PP RETURN RIGHT END (1)
Pae 2

Part Identification
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
G
P
Q
R
S
T
U
V
W
X
Y
ZAA
BB
CC
DD
EE
FF
GG
RS
EE
EE
EE
HH
II
JJ
KK
LL
MM
II
V
CC
BB
DD
LL MM
MM
MM
NN
NN
NN
NN
NN
NN
NN
NN
NN
NN
NN
OO
Pae 3
åNOTE: Part PP will not be used
in the return on left assembly.

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
12 BACK FILE
GLIDE - 1 13 LONG FILE GLIDE - 2
10 FRONT FILE
GLIDE  1
11 FILE
HANGER  4
(EXTENSION SET
SHOWN SEPARATED)
1SHELF SLIDER SET - 1 2LONG EXTENSION
RAIL - 2 3LONG EXTENSION
SLIDE - 2
4EXTENSION RAIL - 2 5EXTENSION SLIDE - 2
LEFT CABINET
RAIL - 3
7LEFT DRAWER
SLIDE - 3
9
RIGHT DRAWER
SLIDE - 3
8
RIGHT CABINET
RAIL - 3
6
14 SHORT FILE
GLIDE - 2
(EXTENSION SET
SHOWN SEPARATED)
Pae 4
(EXTENSION SET
SHOWN SEPARATED)

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
ANGLED HEAD
CAM SCREW - 65
16
Anled head
BLACK 1-1/2" FLAT HEAD SCREW - 44
28 BLACK 1-1/8" FLAT HEAD SCREW - 18 29
BLACK 1/2" FLAT HEAD SCREW - 36
32 SILVER 1/2" FLAT HEAD SCREW - 10 33
SMALL HIDDEN
CAM - 20
17
LARGE HIDDEN
CAM - 65
15
SHORT WOOD
DOWEL - 12
20
LONG WOOD
DOWEL - 40
19
STRAIGHT HEAD
CAM SCREW - 20
18
Straiht head
BLACK 1/2" PAN HEAD SCREW - 40
31
LARGE
APPLIQUE CARD - 1
27
APPLIQUE CARD - 1
26
GROMMET
WITH CAP- 4
24
BLACK 9/16" LARGE HEAD SCREW -4
30
GROMMET - 4
25
PULL - 5
22
BRACKET - 2
21 ADJUSTABLE
GLIDE - 11
23
åScrews are shown actual size. You may receive extra hardware with your unit.
Pae 5
(Do not open parts 17 and 18 until you
are ready to assemble the drawers.)

å Assemble your unit on a carpeted floor or on the empty carton
to avoid scratchin your unit or the floor.
å Push fifty-eiht HIDDEN CAMS (15) into the ENDS (A and B),
UPRIGHT (C), RETURN UPRIGHT (D), SHELVES (G),
BOTTOMS (H, I, and J), BACKS (K and L), RETURN
BACK (N), SHORT UPRIGHT (P), LONG UPRIGHT (Q),
BRACES (S and T), and RETURN LEFT END (OO).
Step 1
Pae 6
Arrow
Arrow
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
Arrow
Arrow
15
15
15
15
K
I
H
B
A
C
N
G
G
P
Q
S
S
D
T
OO
J
L
(58 used)

Step 2
Pae 7
Anled head
16
å Turn twenty ANGLED HEAD CAM SCREWS (16) into the
exact holes shown in the ENDS (A and B), UPRIGHT (C), and
RETURN LEFT END (OO).
(20 used)
B
A
C
OO

Step 3
Pae 8
I
H
J
å Peel the STICKERS from the LARGE APPLIQUE CARD (27) and
stick one onto each metal insert in the BOTTOMS (H, I and J).
27
Surface without
HIDDEN CAMS Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
(12 used)
Some assembly
(and snacks) required.

å Turn eiht FEET (NN) into the SMALL BOTTOMS (H and J).
å NOTE: Do not overtihten the FEET.
å Then, turn eiht ADJUSTABLE GLIDES (23) into the FEET (NN).
å NOTE: Turn the ADJUSTABLE GLIDES completely in. Final
adjustments will be made after the unit is standin upriht.
Step 4
Pae 9
H
J
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
NN
NN
NN
NN
NN
NN
NN
NN
23
(8 used)

Step 5
Pae 10
å Insert four SHORT WOOD DOWELS (20) into the SMALL
BOTTOMS (H and J).
å Fasten four BOTTOM RAILS (MM) to the SMALL BOTTOMS (H
and J). Use eiht BLACK 1-1/8" FLAT HEAD SCREWS (29).
å NOTE: Be sure the SHORT WOOD DOWELS in the SMALL
BOTTOMS insert into the BOTTOM RAILS.
H
J
20
20
MM
MM
MM
MM
MM
BLACK 1-1/8" FLAT HEAD SCREW
(8 used in this step)
29