TMG TMG-DT4041C User manual

►www.tmgindustrial.com 0/12 TOLL FREE:1-877-761-2819

►www.tmgindustrial.com 1/12 TOLL FREE:1-877-761-2819
MAIN SPECIFICATIONS :
Overall assembled size : W12 x L12 x H4.5 (m) / W40 x L39.37 x H15 (ft)
Width : 12 m / 39.37ft
Length : 12 m / 39.37ft
Ridge peak height : 4.5 m / 15ft + container height
Shoulder wall clearance height : 1.05m / 3.4ft
PRIOR TO ASSEMBLY
Please read the instructions carefully before installation. It is very important to follow your local safety
regulations and industry standards during installation. Regulations may include but are not limited to:
- Safety helmets, protective eyewear, and clothing
- Safety harnesses for all elevated workers
- Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part number, please refer to the
parts list to make sure you have all parts.
Choose a day with low or no wind to install, assembly is hard in heavy wind. Do not make any alterations to the structure.
Do not hang any weights on the frame during installation, including parts. We are not responsible for any damages or
injuries caused by inappropriate installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
It is recommended to tape or add foam/rubber on the frame where joints connect and where it touches the cover. This
will help extend the life span of the cover.
Read the following item list carefully and count the number of items to ensure that all parts are included prior to setup.
INSTALLATION STEPS
REVIEW THE WHOLE STRUCTURE AND CHOOSE THE PROPER INSTALLATION SITE
Choose a solid flat level ground area to set up the building. Do not install the building on soft ground, wetland, uneven
surfaces, sloped surfaces, or on top of structures that are not rated to hold its weight.
We strongly recommend that you put the containers on hard foundations before installing the shelter.
Be aware of the surrounding area. Do not set up the building near snowdrifts, open flames or exposed electrical wires. Do
not keep heat sources near the fabric cover. Keep the building surroundings clear at all times.
Check the parts list below to make sure all parts are received prior to assembly.

►www.tmgindustrial.com 2/12 TOLL FREE:1-877-761-2819
TMG-DT4041C PART LIST
PARTS
CODE
PICTURE
DESCRIPTION
LENGTH
QTY
1
Peak arch tube
(for 3 middle trusses )
L2509mm
3
1A
Peak arch tube
(for front and rear truss)
L2509mm
2
2
Upper rafter tube
(middle truss)
L1996mm
6
2A
Upper rafter tube
(front and rear truss)
L1996mm
4
3
Lower rafter tube
(for middle truss)
L2898mm
6
3A
Lower rafter tube
(for front and rear truss)
L2898mm
4
4
Sidewall tube
(middle truss)
L2555mm
6
4A
Sidewall tube
(for front and rear truss)
L2555mm
4
5
Roofpurlin
(horizontal tube)
φ58x3040mm
28
6
Baseplates for middle truss
W200xL340mm
6
6L
Baseplate for front and rear truss left
corners
W200xL340mm
2
6R
Baseplate for front and rear truss
rightcorners
W200xL340mm
2
7
Top cover tension tube
(for both bottom sides)
φ32x1993mm
φ32x500mm
12
2
8
Ridge steel tension cables
(front and rear trusses)
φ8x3500mm
24

►www.tmgindustrial.com 3/12 TOLL FREE:1-877-761-2819
9
Cable connection plate
W90xL90mm
28
10
Ratchets
3T
34
11
Tie down straps
(for #10 and front and rear arches)
W38xL800mm
34
12
Hex bolt and nuts
M12x30mm
160
13
Self locking bolt and nuts
M10x80mm
35
14
Tension tube end water plug
φ32mm
4
15
Plastic hose
(in grooves at both ends of #17)
φ25x4000mm
10
16
Connector (for connection #15)
φ25mm
8
17
Roof fabric tarp cover
1
18
Scratch resistant tape
L10m
2

►www.tmgindustrial.com 4/12 TOLL FREE:1-877-761-2819
STEP 1 : REVIEW THE WHOLE STRUCTURE AND CHOOSE THE PROPER INSTALLATION SI.
PARTS
CODE
PART
QTY
6
6
6L
2
6R
2

►www.tmgindustrial.com 5/12 TOLL FREE:1-877-761-2819
STEP 2 : INSTALLATION OF FRONT AND REAR TRUSSES.
PARTS
CODE
PART
QTY
PARTS
CODE
PART
QTY
1A
1x2
4A
2x2
2A
2x2
12
24x2
3A
2X2

►www.tmgindustrial.com 6/12 TOLL FREE:1-877-761-2819
STEP 3 : STALLATION (3) MIDDLE TRUSSES.
PARTS
CODE
PART
QTY
PARTS
CODE
PART
QTY
1
1x3
4
2x3
2
2x3
12
24x3
3
2x3

►www.tmgindustrial.com 7/12 TOLL FREE:1-877-761-2819
STEP 4 : WRAP (#18) AROUND THE SHARP POINTS OF THE JOINT TO AVOID FRICTION BETWEEN THE FABRIC AND
THE INTERFACE.
PARTS
CODE
PART
QTY
18
2

►www.tmgindustrial.com 8/12 TOLL FREE:1-877-761-2819
STEP 5 : PUT UP ALL TRUSSES.
PARTS
CODE
PART
QTY
PARTS
CODE
PART
QTY
5
7
12
16
8
12
13
14
9
14

►www.tmgindustrial.com 9/12 TOLL FREE:1-877-761-2819
STEP 6 : TENSION CABLE INSTALLATION. ALL CABLES ARE DIAGONALLY INSTALLED ON EACH SIDE OF THE
INTERVAL.
PARTS
CODE
PART
QTY
PARTS
CODE
PART
QTY
5
21
12
24
8
12
13
21
9
14

►www.tmgindustrial.com 10/12 TOLL FREE:1-877-761-2819
STEP 7 : INSTALL ROOF COVER.
PARTS
CODE
PART
QTY
17
1

►www.tmgindustrial.com 11/12 TOLL FREE:1-877-761-2819
STEP 8 : TENSION THE COVER ON THE FRAME FROM SIDE TO SIDE.
PARTS
CODE
PART
QTY
PARTS
CODE
PART
QTY
7
2
14
4
10
34
15
10
11
34
16
8

►www.tmgindustrial.com 12/12 TOLL FREE:1-877-761-2819
AFTER THE INSTALLATION
Walk around and inspect the shelter periodically to make sure all components are still firmly secured and the
whole shelter is well supported. Check all bolts and nuts as well as all connection points to make sure they are all
in good position. Check the base plates, adjust the ropes and tie downs if required and clean the cover regularly.
Snow accumulating on the fabric cover must be removed as soon as possible. If snow becomes solid ice on the
cover, it will increase the weight on the roof and may collapse the shelter or reduce the life span.
Keep the shelter on a dry ground most of the time. Do not keep the fabric dirt skirt under water all the time,
otherwise the fabric will deteriorate.
We strongly recommend you remove any snow from the roof immediately. Do not leave any snow load on the roof
overnight. Keep 3 feet of clearance on all sides at all times. Do not allow snow to accumulate and pile up on the
sides of the building. Otherwise the pressure from the sides will push inwards and could lead to a collapse.