TMG TMG-DT3041-PRO User manual

▶W W W . T M G I N D U ST R I A L . C O M P 0 / 2 6 T o l l F r e e : 1 - 877-761-2819

▶W W W . T M G I N D U ST R I A L . C O M P 1 / 2 6 T o l l F r e e : 1 - 877-761-2819
Main Specifications :
Assembly size : W9.15 x L12 x H6 (m) / 30 x 39.37 x 19.68 (ft)
Ridge height : 6m / 19.68 ft
Peak clearance : 5.4m / 17.7 ft
Front door : 4.27 x 3.96 (m) / 14 x 13 (ft)
Shoulder height : 3.6 m / 11.8 ft
Prior to assembly
Please read the instructions carefully before installation. It is very important to follow
your local safety regulations and industry standards during installation. Regulations may
include but are not limited to:
• Safety helmets, protective eyewear, and clothing
• Safety harnesses for all elevated workers
• Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part
number, please refer to the parts list to ensure you have all parts.
Choose a day with low or no wind to install, it is hard to assemble with heavy wind. Do
not make any alterations to the structure. Do not hang any weight on the frame during
installation, including parts. We are not responsible for any damages or injuries caused by
inappropriate installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
It is recommended to use heavy duty duct tapes to tape the tube connection joint spots to
protect the cover from damage and worn. It will help to extend the cover life span.
Check the parts list below to make sure all parts are received prior to assembly.

▶W W W . T M G I N D U ST R I A L . C O M P 2 / 2 6 T o l l F r e e : 1 - 877-761-2819
Frame structure diagram.

▶W W W . T M G I N D U ST R I A L . C O M P 3 / 2 6 T o l l F r e e : 1 - 877-761-2819
TMG-DT3041-PRO Part List
Parts
Code
Graphical
Description
Length
Qty
Box
1
Peak arch tube
(for 4 middle trusses )
2570mm
4
B
1A
Peak arch tube
(for front and rear
truss)
2570mm
2
B
2
Upper rafter tube
(for middle trusses)
2921mm
8
A
2A
Upper rafter tube
(for front and rear
truss)
2921mm
4
A
3
Shoulder tube
(for middle trusses)
1757mm
8
A
3A
Shoulder tube
(front and rear
trusses)
1757mm
4
A
4
Sidewall tube
(middle trusses)
2878mm
8
A
4A
Sidewall tube
(Front and rear left
truss)
2878mm
3
A
4B
Sidewall tube
(Front right truss)
2878mm
1
A
5
Roof purlin
(horizontal tube)
2440mm
45
A
5L
Baseplate for front
and rear truss left
corners
W260xL520mm
2
B
5R
Baseplate for front
and rear truss right
corners
W260xL520mm
2
B
6
Rear door left column
baseplate
W150xL200mm
1
B

▶W W W . T M G I N D U ST R I A L . C O M P 4 / 2 6 T o l l F r e e : 1 - 877-761-2819
6A
Rear door right
column baseplate
W150xL200mm
1
B
6B
Rear door middle
column baseplate
W150xL200mm
1
B
6L
Left baseplate of
front door frame
W150xL200mm
1
B
6R
Right baseplate of
front door frame
W150xL200mm
1
B
7
Baseplates for middle
truss
W260xL480mm
8
B
7A
Ratchets
(3T)
40
B
7B
Expansion bolts
φ16x150mm
62
B
8
Ceiling cross bar
(front truss)
2083mm
1
B
9
Ceiling cross bar
(front truss)
2233mm
1
B
9L
Front vertical door
rail
(left side upper part)
1984mm
1
B
9R
Front vertical door
rail
(right side upper part)
1984mm
1
B
9A
Side door left tube
2027mm
1
B
9B
Side door right tube
2027mm
1
B
9C
Side door
L2005xW925mm
1
B
10
Door center vertical
supporting rod for
cross beam (front
truss)
1018mm
1
B

▶W W W . T M G I N D U ST R I A L . C O M P 5 / 2 6 T o l l F r e e : 1 - 877-761-2819
10A
Lower vertical tubes
for rear trusses
2580mm
3
B
10B
Left and right upper
vertical tubes for rear
trusses
1990mm
2
B
10C
Middle upper vertical
tubes for rear trusses
2874mm
1
B
10L
Front vertical door
rail
(left side lower part)
2625mm
1
B
10R
Front vertical door
rail
(right side lower part)
2625mm
1
B
11
Door frame
horizontal tube
(front truss)
1982mm
3
B
11A
Door frame middle
horizontal tube (rear
truss)
2123mm
4
B
11B
Door frame
horizontal tube
(rear truss)
1996mm
4
B
11C
Side door upper tube
1980mm
1
B
12
Left and right bottom
tension bar (front and
rear truss)
1970mm
3
B
12A
Middle bottom
tension bar
(rear truss)
2070mm
2
B
12B
Bottom tension bar
815mm
1
B
13
Front door hand
winch crossing tube
1984mm
1
B
14
Top cover tension
tube
1993mm
12
B

▶W W W . T M G I N D U ST R I A L . C O M P 6 / 2 6 T o l l F r e e : 1 - 877-761-2819
14A
Top cover tension
tube
500mm
2
B
15
Front roll up door
dropping tubes
(to connect #16)
2195mm
7
B
16
Front roll up door
dropping tubes
(to connect #15)
2192mm
7
B
17
Sidewall frame steel
tension cables
φ6x4050mm
14
B
18
Ridge steel tension
cables
(front and rear
trusses)
φ6x2800mm
24
B
19
Middle truss crossing
steel tension cables
φ6x3990mm
4
B
20
Front and rear truss
left and right steel
cables
φ6x3900mm
4
B
21
Tie down straps
(for #7A)
W38xL800mm
40
B
22
Cable connection
plate
91mm
32
B
22A
Pressing plate
2m
6
B
22B
Pressing plate
1m
1
B
23
Roll up door hand
winch
(1200 lb)
1
B
23A
Wire rope for front
hand winch
φ4mm x 15m
1
B
23B
Right pulley system
for front door
150mm
1
B
23C
Left pulley system for
front door
150mm
1
B
24
Front vertical door
rail connection plate
240mm
2
B

▶W W W . T M G I N D U ST R I A L . C O M P 7 / 2 6 T o l l F r e e : 1 - 877-761-2819
24A
Front vertical door
rail end plate
(floatable to keep
door rail straight)
220mm
2
B
25
Tension tube end
water plug
(φ32)
16
B
26
Tube clamps
(φ48)
6
B
27
Tapping screw
#12x25mm
60
B
28
Self locking bolt
and nuts
M10x70mm
54
B
29
Strengthened bolt
and nuts
M12x30mm
192
B
30
Hex bolt and nuts
M10x50mm
14
B
31
Hex bolt and nuts
M10x70mm
58
B
32
Braided rope
160m
1
B
33
Roof fabric tarp cover
W12.6xL18.4m
1
B
34
Front truss cover
panel
W6.2xL9.1m
1
B
34A
Rear truss fabric
cover panel
W6.2xL9.1m
1
B
35
Front roll up door
cover panel
W4.2xL4.6m
1
B
36
Front fabric tarp
secure pin
200mm
1
B
37
Plastic hose
(in grooves at both
ends of #33)
φ25mmxL4m
10
B
37A
Connector
(for connection #37)
φ25mm
8
B
38
Scratch resistant tape
10m
2
B

▶W W W . T M G I N D U ST R I A L . C O M P 8 / 2 6 T o l l F r e e : 1 - 877-761-2819
Step 1 : Baseplate positioning and installation.
Installation diagram of expansion bolt.
No.
Part
Qty
No.
Part
Qty
5L
2
6A
1
5R
2
6B
1
6L
1
7
8
6R
1
7B
58
6
1

▶W W W . T M G I N D U ST R I A L . C O M P 9 / 2 6 T o l l F r e e : 1 - 877-761-2819
Step 2 :Assemble all trusses.
 Front truss.
No.
Part
Qty
No.
Part
Qty
1A
1
4A
1
2A
2
4B
1
3A
2
29
24

▶W W W . TM G I N D U ST R I A L . C OM P 10/ 2 6 T o l l F r ee : 1 - 877- 7 6 1 - 2 8 1 9
 Rear truss.
No.
Part
Qty
No.
Part
Qty
1A
1
4A
2
2A
2
29
24
3A
2

▶W W W . TM G I N D U ST R I A L . C OM P 11/ 2 6 T o l l F r ee : 1 - 877- 7 6 1 - 2 8 1 9
 Middle trusses. (4 trusses)
No.
Part
Qty
No.
Part
Qty
1
1x4
4
2x4
2
2x4
29
24x4
3
2x4

▶W W W . TM G I N D U ST R I A L . C OM P 12/ 2 6 T o l l F r ee : 1 - 877- 7 6 1 - 2 8 1 9
 Lay down all (6) trusses on the ground when the assembly is all completed and
before moving to next step, and then wrap (#38) around the sharp points of
the joint to avoid friction between the fabric and the interface, resulting in
fabric damage.
No.
Part
Qty
38
2

▶W W W . TM G I N D U ST R I A L . C OM P 13/ 2 6 T o l l F r ee : 1 - 877- 7 6 1 - 2 8 1 9
Step 3 : Put up the front truss. (It is suggested to use crane for hoisting)
No.
Part
Qty
29
8

▶W W W . TM G I N D U ST R I A L . C OM P 14/ 2 6 T o l l F r ee : 1 - 877- 7 6 1 - 2 8 1 9
Step 4 : Put up the rest trusses.
 Refer to step 3 to put up the rest trusses, connect all purlins (#5) with bolt
(#28) and secure all bolts firmly on each span before going to next truss .
No.
Part
Qty
No.
Part
Qty
5
9
29
8
28
18

▶W W W . TM G I N D U ST R I A L . C OM P 15/ 2 6 T o l l F r ee : 1 - 877- 7 6 1 - 2 8 1 9
 Repeat above step to put up all other trusses (from 3rd to 6th truss), and
connect all purlins.
No.
Part
Qty
No.
Part
Qty
5
36
29
32
28
36

▶W W W . TM G I N D U ST R I A L . C OM P 16/ 2 6 T o l l F r ee : 1 - 877- 7 6 1 - 2 8 1 9
 Tension cable installation . All cables are diagonally installed on each side of
the interval.
No.
Part
Qty
No.
Part
Qty
17
14
19
4
18
24
22
32
Step 5 : Front and rear trusses to complete.

▶W W W . TM G I N D U ST R I A L . C OM P 17/ 2 6 T o l l F r ee : 1 - 877- 7 6 1 - 2 8 1 9
 Front truss
No.
Part
Qty
No.
Part
Qty
7B
4
12
1
8
1
12B
1
9
1
13
1
9A
1
20
2
9B
1
23B
1
9C
1
23C
1
9L
1
24
2
9R
1
24A
2
10L
1
25
4

▶W W W . TM G I N D U ST R I A L . C OM P 18/ 2 6 T o l l F r ee : 1 - 877- 7 6 1 - 2 8 1 9
10R
1
26
3
10
1
30
7
11
3
31
32
11C
1
27
8
 Rear truss
No.
Part
Qty
No.
Part
Qty
10A
3
12A
2
10B
2
20
2
10C
1
25
8
11A
4
26
3
11B
4
30
7
12
2
31
24

▶W W W . TM G I N D U ST R I A L . C OM P 19/ 2 6 T o l l F r ee : 1 - 877- 7 6 1 - 2 8 1 9
Step 6 : Install front and rear cover panels.
 Front cover panel
 Lift up (#34) cover panel, starting from the center point of the frame (highest
ridge point) use ropes (#32) through the grommets to tie the panel to the truss
firmly. All grommets need to be tied to the frame as shown.
No.
Part
Qty
No.
Part
Qty
32
1
34
1