TMG TMG-DT3380 User manual

www.tmgindustrial.com 0/19 Toll Free:1-877-761-2819

www.tmgindustrial.com 1/19 Toll Free:1-877-761-2819
MAIN SPECIFICATIONS :
 Assembly size : W10 x L24 x H6 (m) / 32.8 x 78.7 x 19.7 (ft)
 Ridge height : 6m / 19.7ft
 Peak clearance : 5.4m / 17.7 ft
 Door : 5.7x 2.68 (m) / 18.7 x 8.8 (ft)
 Shoulder height : 3.46m / 11.4ft
CONCRETE FOUNDATION SIZE SEE BELOW FIGURE.
PRIOR TO ASSEMBLY
Please go through the whole instruction manual completely. It is very important to follow your local safety regulations
and industry standards during installation. Regulations may include but are not limited to :
- Safety helmets, protective eyewear, and clothing
- Safety harnesses for all elevated workers
- Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part number, please refer to the parts
list to ensure you have all parts.
Choose a day with low or no wind to install, it is hard to assemble with heavy wind. Do not make any alterations to the
structure. Do not hang any weight on the frame during installation, including parts. We are not responsible for any
damages or injuries caused by inappropriate installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
It is recommended to use heavy duty duct tapes to tape the tube connection joint spots to protect the cover from

www.tmgindustrial.com 2/19 Toll Free:1-877-761-2819
damage and worn. It will help to extend the cover life span.
Check the parts list below to make sure all parts are received prior to assembly.
FRAME STRUCTURE DIAGRAM.

www.tmgindustrial.com 3/19 Toll Free:1-877-761-2819
TMG-DT3380 PART LIST
PARTS
CODE
GRAPHICAL
DESCRIPTION
LENGTH
QTY
BOX
1
Peak arch tube
(for 7 middle trusses )
2570mm
7
A
1A
Peak arch tube
(for front and rear truss)
2570mm
2
A
2
Upper rafter tube
(for middle trusses)
3390mm
14
A
2A
Upper rafter tube
(for front and rear truss)
3390mm
4
A
3
Shoulder tube
(for middle trusses)
1757mm
7
C
3A
Shoulder tube
(front and rear trusses)
1757mm
4
C
3B
Shoulder tube
(for middle trusses)
1401mm
7
B
4
Sidewall tube
(middle trusses)
2680mm
7
A
4A
Sidewall tube
(Front and rear truss)
2680mm
4
A
4B
Door upright column
2647mm
2
C
4L
Door upright column
2647mm
1
C
4R
Door upright column
2647mm
1
C
5
Roof purlin
(horizontal tube)
φ48xL3040mm
64
A
5A
Roof purlin
(horizontal tube)
φ48xL2840mm
2
A
5L
Baseplate for front and rear
truss left corners
W260xL520mm
2
C

www.tmgindustrial.com 4/19 Toll Free:1-877-761-2819
5R
Baseplate for front and rear
truss right corners
W260xL520mm
2
C
6B
Baseplate
W150xL200mm
6
C
7
Baseplates for middle truss
W260xL480mm
7
C
7A
Ratchets
(3T)
48
B
7B
Expansion bolts
φ16xL150mm
72
C
8
Middle upper vertical tubes
φ48xL2555mm
2
A
8A
Lower vertical tubes
φ48xL2896mm
6
A
9
Left and right upper
vertical tubes
φ48xL1588mm
4
A
10
Middle horizontal tube
φ48xL2288mm
8
B
11
Horizontal tube
φ48xL2253mm
8
A
12
Left and right bottom tension
bar (front and rear truss)
Φ32xL2235mm
8
A
13
Top cover tension tube
(for both bottom sides)
φ32xL1993mm
21
A
13A
Top cover tension tube
(for both bottom sides)
φ32xL1000mm
2
A
13B
Top cover tension tube
(for both bottom sides)
φ32xL3200mm
2
A
14L
Left door beam
3060mm
1
B
14R
Right door beam
3060mm
1
B
15
Door beam
3000mm
4
B
16
Sidewall frame steel
tension cables
φ6xL4110mm
14
C

www.tmgindustrial.com 5/19 Toll Free:1-877-761-2819
16A
Ridge steel tension cables
(front and rear trusses)
φ6xL3130mm
24
C
17
Middle truss crossing steel
tension cables
φ6xL3990mm
7
C
18
Tie down straps
(for #7A)
W38xL800mm
48
C
19
Cable connection plate
91mm
31
C
20
Tension tube end water plug
(φ32)
24
C
21
Tube clamps
(φ48)
6
C
22
Scratch resistant tape
10m
4
C
23
Self locking bolt
and nuts
M10x70mm
74
C
24
Strengthened bolt
and nuts
M12x30mm
232
C
25
Hex bolt and nuts
M12x40mm
74
C
26
Hex bolt and nuts
M10x30mm
10
C
26A
Hex bolt and nuts
M10x50mm
6
C
27
Hex bolt and nuts
M10x70mm
42
C
28
Braided rope
φ8x250m
1
C
29
Roof fabric tarp cover
W18.7xL24.6m
1
C
30
Front truss cover panel
W6.2xL10m
2
C
31
Plastic hose (in grooves at
both ends of #29)
φ25mm x L4m
10
C
32
Connector
(for connection #31)
φ25mm
8
C

www.tmgindustrial.com 6/19 Toll Free:1-877-761-2819
STEP 1 : BASEPLATE POSIT INSTALLATION.
Installation diagram of expansion bolt.
NO.
PART
QTY
NO.
PART
QTY
5L
2
7
7
5R
2
7B
56
6B
6
STEP 2 : INSTALLING THE DOOR FRAME.

www.tmgindustrial.com 7/19 Toll Free:1-877-761-2819
 Install the door frame according to the base plate datum in step 1.
NO.
PART
QTY
NO.
PART
QTY
4B
2
14L
1
4L
1
14R
1
4R
1
15
4
7B
16
25
46
STEP 3 : ASSEMBLE ALL TRUSSES.

www.tmgindustrial.com 8/19 Toll Free:1-877-761-2819
 Front and rear trusses.
NO.
PART
QTY
NO.
PART
QTY
1A
1x2
4A
2x2
2A
2x2
24
24x2
3A
2x2
 Middle trusses. (7 trusses)

www.tmgindustrial.com 9/19 Toll Free:1-877-761-2819
NO.
PART
QTY
NO.
PART
QTY
1
1x7
3B
1x7
2
2x7
4
1x7
3
1x7
24
20x7
 Lay down all (9) trusses on the ground when the assembly is all completed and before moving to next step, and
then wrap (#22) around the sharp points of the joint to avoid friction between the fabric and the interface,

www.tmgindustrial.com 10/19 Toll Free:1-877-761-2819
resulting in fabric damage.
NO.
PART
QTY
22
4
STEP 4 : PUT UP THE FRONT TRUSS. (IT IS SUGGESTED TO USE CRANE FOR HOISTING)

www.tmgindustrial.com 11/19 Toll Free:1-877-761-2819
NO.
PART
QTY
24
8
STEP 5 : PUT UP THE REST TRUSSES

www.tmgindustrial.com 12/19 Toll Free:1-877-761-2819
 Refer to step 4 to put up the rest trusses, connect all purlins (#5) with bolt (#28) and secure all bolts firmly
on each span before going to next truss .
NO.
PART
QTY
NO.
PART
QTY
5
8
24
4
5A
1
25
4
23
17
26
1
 Repeat above step to put up all other trusses (from 3rd to 9th truss), and connect all purlins.

www.tmgindustrial.com 13/19 Toll Free:1-877-761-2819
NO.
PART
QTY
NO.
PART
QTY
5
56
24
32
5A
1
25
24
23
57
26
1
 Tension cable installation . All cables are diagonally installed on each side of the interval.

www.tmgindustrial.com 14/19 Toll Free:1-877-761-2819
NO.
PART
QTY
NO.
PART
QTY
16
14
17
7
16A
24
19
31
STEP 6 : FRONT AND REAR TRUSSES TO COMPLETE.

www.tmgindustrial.com 15/19 Toll Free:1-877-761-2819
NO.
PART
QTY
NO.
PART
QTY
8
1x2
20
8x2
8A
3x2
21
3x2
9
2x2
26
4x2
10
4x2
26A
3x2
11
4x2
27
21x2
12
4x2
STEP 7 : INSTALL FRONT AND REAR COVER PANELS.

www.tmgindustrial.com 16/19 Toll Free:1-877-761-2819
 Lift up (#30) cover panel, starting from the center point of the frame (highest ridge point) use ropes (#28)
through the grommets to tie the panel to the truss firmly. All grommets need to be tied to the frame as shown.
NO.
PART
QTY
ROPE SHEAR SIZE
30
1x2
28
QTY
A
19000mm
2x2
B
18000mm
3x2
STEP 8 : INSTALL ROOF COVER.

www.tmgindustrial.com 17/19 Toll Free:1-877-761-2819
 NOTE: The cover must be installed on a windless day. DO NOT attempt to install the cover during windy
conditions.
NO.
PART
QTY
29
1
 After the cover is installed on the roof, insert the plastic pipe (#31) slowly into the grooves on two ends of the

www.tmgindustrial.com 18/19 Toll Free:1-877-761-2819
cover (not two sides), and then insert tension tubes (#13,#13A,#13B) in the groove on both sides of the cover
bottom, Add the water plug (#20) on the 1st tube (#13) to protect the fabric while the tube is going through and
add the water plug on the last tube also to keep water away.
 Stretch and adjust the cover from left and right, back and forth, to make sure it is square and centered. Cut the
grooves from inner side facing to the ratchet hardware (#7A), and add tie down straps (#18) to pull the tension
tube and tie the strap to the base.
NO.
PART
QTY
ROPE SHEAR SIZE
7A
48
28
QTY
13
21
13A
2
C
4000mm
2
13B
2
D
17000mm
2
18
48
20
8
31
10
32
8
AFTER THE INSTALLATION

www.tmgindustrial.com 19/19 Toll Free:1-877-761-2819
Walk around and inspect the building periodically to make sure all components are still firmly secured and the whole
building is well supported. Check all bolts and nuts as well as all connection points to make sure they are all in good
position. Check the base plates, adjust the ropes and tie downs if required and clean the cover regularly.
Snow accumulating on the fabric cover must be removed as soon as possible. If snow becomes solid ice on the cover, it
will increase the weight on the roof and collapses the building or reduce the life span eventually.
Keep the building on a dry ground most of the time. Do not keep the fabric dirt skirt under water all the time, otherwise
the fabric will deteriorate.
We strongly recommend you remove any snow from the roof immediately. Do not leave any snow load on the roof
overnight. Keep 3 feet of clearance on all sides at all times. Do not allow snow to accumulate and pile up on the sides of
the building. Otherwise the push from the sides toward inside will make the building collapsed at some point.