TMG TMG-ST2040C-1.0 User manual

W W W . T M G I N D U S T R I A L . C O M P 0 / 9 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9

W W W . T M G I N D U S T R I A L . C O M P 1 / 9 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
Main Specifications :
Overall assembled size : W6 x L12 x H2 (m) / 20 x 40 x 6.5 (ft)
Width : 6 m / 20ft
Length : 12 m / 40 ft
Ridge Peak Height : 2 m / 6.5 ft
Shoulder wall clearance height : 0.5 m / 1.6 ft
Prior to assembly
Please read the instructions carefully before installation. It is very important to follow your
local safety regulations and industry standards during installation. Regulations may include
but are not limited to:
- Safety helmets, protective eyewear, and clothing
- Safety harnesses for all elevatedworkers
- Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part
number, please refer to the parts list to make sure you have all parts.
Choose a day with low or no wind to install, assembly is hard in heavy wind. Do not make
any alterations to the structure. Do not hang any weights on the frame during installation,
including parts. We are not responsible for any damages or injuries caused by
inappropriate installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
It is recommended to tape or add foam/rubber on the frame where joints connect and
where it touches the cover. This will help extend the life span of the cover.
Read the following item list carefully and count the number of items to ensure that all parts
are included prior to setup.

W W W . T M G I N D U S T R I A L . C O M P 2 / 9 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
Installation steps
Step 1 : Review the whole structure and choose the proper installation site
Choose a solid flat level ground area to set up the building. Do not install the building on
soft ground, wetland, uneven surfaces, sloped surfaces, or on top of structures that are not
rated to hold its weight.
We strongly recommend that you put the containers on hard foundations before installing
the shelter.
Be aware of the surrounding area. Do not set up the building near snowdrifts, open flames
or exposed electrical wires. Do not keep heat sources near the fabric cover. Keep the
building surroundings clear at all times.
TMG-ST2040C-1.0 Part List
No.
Picture
Description
Quantity
BOX
1
Peak arch tube
9
1/1
2
Middle rafter tube
18
1/1
3
Shoulder tube
18
1/1
4
Purlin tube
40
1/1
5
Middle truss baseplate
14
1/1
5L
Left corner baseplate
(front and rear truss)
2
1/1
5R
Right corner baseplate
(front and rear truss)
2
1/1
6
Top cover tension tube
A
12
1/1

W W W . T M G I N D U S T R I A L . C O M P 3 / 9 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
7
Top cover tension tube
B
2
1/1
8
Ratchets
18
1/1
9
Tie down straps
18
1/1
10
Hex bolt
M10x70mm
108
1/1
11
Locking bolt
M10x80mm
45
1/1
12
Top cover
1
1/1
13
Water plug
4
1/1
14
Braided rope
1
1/1
15
Scratch resistant tape
2
1/1
Step 2 : Place the containers making sure they are parallel and the correct width apart.
Make sure there is a gap of about 3 feet around the building. the center point of the round
pipe of the base is the reference point, and the diagonal X and Y must be equal. The base
plate shall be welded to the top of the container on the same horizontal plane to ensure that
the welding is firm and reliable. (refer to picture 1）
Components are :
(14) Middle truss baseplate (#5)
(2) Left corner baseplate (#5L)
(2) Right corner baseplate (#5R)

W W W . T M G I N D U S T R I A L . C O M P 4 / 9 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
Picture 1
Step 3 : Connect all trusses
Layout all truss components on the ground in the correct configuration before bolting them
together.
Components are :
(1x9) Peak arch tube (#1)
(2x9) Middle rafter tube (#2)
(2x9) Shoulder tube (#3)
(8x9) Hex bolt (#10)
(2) Scratch resistant tape (#15)

W W W . T M G I N D U S T R I A L . C O M P 5 / 9 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
There are total 9 trusses to build, use the hex bolt (#10) to connect all tubes together, wrap (#15)
around truss joints (refer picture 2 as below)
Picture 2
Step 4 : Put up all trusses
Install each truss on the base tube.Use hex bolt (#10) to secure the truss to the truss
baseplate. We recommend to use a crane or forklift to lift the truss and have 2 to 3 people
on site to work together. Please make sure it is safe and secure when while installation is
proceeding (refer picture 3 as below).

W W W . T M G I N D U S T R I A L . C O M P 6 / 9 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
Picture 3
Install purlin tubes (#4) and use locking bolts (#11) (refer picture 4 as below).
Components are :
(40) Purlin tube (#4)
(45) Locking bolt (#11)
Picture 4
Step 5 : Install the Ratchets.
Install the ratchets on the bottom plates on both sides. (refer Picture 5 as below).
Components are :
(18)Ratchets (#8)

W W W . T M G I N D U S T R I A L . C O M P 7 / 9 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
Picture 5
Overall structural inspection : check all components and trusses to ensure the entire structure
is rectangular as specified in (picture 1). All trusses must be 90 degrees straight up from the
container.
Secure and tighten all bolts and nuts on this step. But do not over tie! Otherwise you might
damage the tubes or components.
Step 6 : Install the cover
Pass the tie down straps (#9) through the top cover and tie it to the top cover tension tube and
pass the other end through the ratchet, adjust the ratchet to tighten. Pull the front cover and back
cover and tie them to the truss. All four sides must be firmly tied together at the same time to
ensure that it is square, smooth and straight. All grommets need to be fixed to the frame with
wavy lines. Finally, install the waterproof plugs to both ends of the top cover tension tube (see
picture 6 and picture 7 below).

W W W . T M G I N D U S T R I A L . C O M P 8 / 9 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
Components are :
(12) Top cover tension tube A (#6)
(2) Top cover tension tube B (#7)
(18) Tie down straps (#9)
(1) Top cover (#12)
(4) Water plug (#13)
(1) Braided rope (#14)
Picture 6

W W W . T M G I N D U S T R I A L . C O M P 9 / 9 T o l l F r e e : 1 - 8 7 7 - 7 6 1 - 2 8 1 9
Picture 7
After Installation
Walk around and inspect the building periodically to make sure the parts are firmly fixed
and the whole building is well supported. Check all bolts and hardware connectors to
make sure they are in place and tightened. Check the base plates, adjust the ropes if
necessary and clean the cover regularly.
Snow accumulating on the fabric cover must be removed as soon as possible. Ifsnow is
allowed to become solid ice on the cover, it could increase theweight on the roof and
collapse the buildingor reduce the life span.
We strongly recommend you remove any snow from the roof immediately. Do not leave any
snow load on the roof overnight. Keep 3 feet of clearance onall sides at all times. Do not allow
snow to accumulate and pile up on the sides of the building. Otherwise the pressure from the
sides will push inwards and could lead to a collapse.