TOORX BRXOffice Compact User manual

Ed: 02/17 Rev : 00
MANUALE d’ISTRUZIONI

PRODUCT OVERVIEW
Meter
Upright
Right
Pedal
Lever Cover
Right Crank
Levering
Cap
Front Stabilizer
Top Cover
Back Cushion
Back
Support
Desktop
djustment Knob
Adjustment Knob
Seat
End Cap
Wheel
Rear Stabilizer
THEFOLLOWINGTOOLS ARE INCLUDED
Wrench:
FOR ASSEMBLY
Allen Wrench (5mm) w/ Screwdriver:
Meter
Back Frame

HARDWARE IDENTIFICATION CHART
Figure No.
Description Qty
D5
D8
Carriage Bolt (M8 * 1.25 * 60mm)
Carriage Bolt (M8 * 1.25 x*45mm)
4
2
D7 Bolt, Button Head (M6*1 *12mm) 4
D17 Screw, Round Head (M6* 12mm) 1
D22 Acorn Nut (M8*1.25) 4
D23 Arc Washer (M8) 4
D24 Washer (M8) 6
D25 Nut M8 2
D1 Adjustment Knob 2
D2
Pull Pin
1

A
AS SS SE EM MB BL LY Y I IN NS ST TR RU UC CT TI IO ON N
Place all parts from the box in a cleared area and position them on the floor in front of you.
Remove all packing materials from your area and place them back into the box. Do not
dispose of the packing materials until assembly is completed. Read each step carefully
before beginning.
STEP 1: Unfold the Rear Frame (A2) away from the Main Frame (A1). Locking the frame
assembly in unfold position by inserting the Pull PIN (D2) into the hole in the Rear Frame
(A2). Forward pushing Upright (A3) to the maximum angle and stepping down to fixed
the Lever Cover (B6).
STEP2: Attach the Rear Stabilizer (A10), the one with Transport Wheels (B19), to the Rear
Frame (A2) with the wheels facing backward. Secure with Carriage Bolts
(M8*1.25*60mm) (D5), Acorn Nuts (M8) (D23), and Arc Washers (M8*1.25) (D22).
STEP 3: Attach the Front Stabilizer (A5) to the Main Frame (A1) with Carriage Bolts
(M8*1.25*60mm) (D5), Acorn Nuts (M8) (D23), and Arc Washers (M8*1.25) (D22).
A.

A
AS SS SE EM MB BL LY Y I IN NS ST TR RU UC CT TI IO ON N
STEP 4: Attach the Seat (B24) to the Seat Post (A6) with Nylock Nuts (M8) (D25) and Washer
(M8) (D38). Insert the Seat Post (B24) into the Main Frame (A1) and secure with the
Adjustment Knob (D1).
NOTE:
1. Make sure that the pin on the Adjustment Knob (D1) is inserted into one of the holes in Seat
Post (B24).
2. The Adjustment Knob (D1) should be screwed in tight to make the Seat Post (B24) fit securely
in the Main Frame (A1).
STEP 5: Attach the Back Support (A7) and Back Frame (A6) by using Carriage Bolt
(M8*1.25*45mm) and Washer (M8) (D24).

A
AS SS SE EM MB BL LY Y I IN NS ST TR RU UC CT TI IO ON N
STEP 6: Attach the Desktop post (A4) to the Desktop (B10) with Button Head Bolts
(M8*1.25*12mm) (D14) and Washer (M8) (D24).
STEP7: Insert the Desktop Post (A4) into the Upright (A3) and secure with the Adjustment Knob
(D1). Bolt the Round Head Bolt (M6*1*12 mm) (D17) onto the Upright (A3) for security.
NOTE:
1. Make sure that the pin on the Adjustment Knob (D1) is inserted into one of the holes in
Desktop Post (A4).
2. The Adjustment Knob (D1) should be screwed in tight to make the Desktop Post (A4) fit
securely in the Upright (A3).
STEP8: Connecting Meter Transmission Wire (C2) into the Sensor Bracket (C13) .

STEP 9: Lock and tight the Left Pedal (B27) and Right Pedal (B28) on the Left Crank (B29) and
Right Crank (B30) by using the Wrench.
FUNCTION INSPECTION:
Visually inspect the Bike to verify that assembly is as shown in the above illustration.
Check the function of the Bike by turning the c rank s lowly through one complete revolution to
verify that the drive train functions properly. Adjust the Adjustment Knob (B32) and verify that it
functions properly and the resistance changes.

OPERATIONAL INSTRUCITONS
USING THE FITNESS METER
MODE: This key lets you to select and lock on to a pa ticula
function you want.
SET(IF HAVE) :To set the values of time. distance and calo ies
when not in scan mode.
RESET/CLEAR (IF HAVE): The key to eset the value to ze o by
p essing the key .
FUNCTIONS:
SCAN: Automatically scans each function of SPEED,
DISTANCE,TIME, ODOMETER, CALORIES and
PULSE. in sequence, display changes every six
seconds. Press and release the button until "SCAN"
appears on the display.
TIME: Displays the time f om one second up to 99:59 minutes.
SPEED : Displays the current speed from zero to 999.9 KM per hour.
DISTANCE : Displays the distance from zero to 999.9 KM.
CALORIES: Displays the calories burned from zero to 999.9 Kcal.
The calorie readout is an estimate for an average user. It should be used only as a
comparison between workouts on this unit.
ODOMETER : Displays the total accumulated distance you have traveled from zero to 9999 KM. The
total accumulated distance is retained when the meter is turned off.
PULSE: Displays your pulse rate in beats per minute. To display pulse, select the PULSE MODE and
grasp the pulse sensors on the Desktop, one in each hand. The heart icon will begin flashing
when the ELECTRONIC METER senses your pulse. Your pulse will be displayed approximately
five (5) seconds after the heart icon is displayed. If the heart icon does not appear, relax your
grip or change your grip on the pulse sensors.
NOTE:
1. NOTE: The meter will shut off automatically after four minutes of inactivity. All function values
will be kept. Press the button and hold it down for two seconds to reset all functions to zero, except
ODOMETER.
TIME
SCAN SPEED DISTANCE CALORIES ODO PULSE
MODE

HOW TO INSTALL AND REPLACE BATTERIES
1. Open the Meter (C1) by using the Shaped Wrench (D3).
D3
C1
2. The meter operates with two AAA batteries, the batteries are not included. After changing the batteries,
push the Meter (C1) back and press down to reset.
B10
C1 Front
A
B
Back
NOTE:
1. Do not mix a new battery with an old battery.
2. Use the same type of battery. Do not mix an alkaline battery with another type of battery.
3. Rechargeable batteries are not recommended.
4. Ultimate disposal of battery should be handled according to all state laws and regulations.
5. Do not dispose of batteries in fire.

B32
D1
A6
A1
A7
LOAD ADJUSTMENT
To increase the load, turn the 8 Section Adjustment Knob (B32) clockwise.
To decrease the load, turn the 8 Section Adjustment Knob (B32) counterclockwise.
There are eight levels for the load adjustment.
SEAT ADJUSTMENT
Proper seat adjustment is important.
1. Turn the Adjustment Knob (D1) to loosen, then pull the
Adjustment Knob (D1) to release the pin. Slide the Seat Post
(A6) until the Seat (A7) is at the proper height. Release the
Adjustment Knob (D1) making sure the pin catches in one of
the holes of the Seat Post (A6) and tighten the Adjustment
Knob (D1).
2. Sit on the seat and place your feet on the pedals. You
should be able to move through a complete pedal
stroke without locking your knees or shifting your hips
on the seat. The seat is too close to the pedals if you
have more than as light bend in your knees at the
bottom of the pedal stroke. The seat is too far from the
pedals if you have to completely straighten your knees
at the bottom of the pedal stroke. Refer to the
illustration.
CAUTION:
1. Do not attempt to adjust the seat while you are on
the BIKE.
2. Always tighten the Adjustment Knob (D1) after
adjusting the seat to a new position.

OPER
A
TIONALINSTRUCTIONS
STORAGE
• To store the BIKE, simply keep it in a clean dry place.
• To avoid damage to the electronics, remove the batteries before storing the BIKE for one year or more.
• Follow the illustrated process below to fold the BIKE.
Remove the Pull Pin (D2), fold the Rear Frame (A2) forward. Insert the Pull Pin (D2) back into the Rear
Frame (A2) after folding.
Remove the Pull Pin (D2) from the Rear Frame (A2).Fold the Rear Frame (A2) close to the Main
Frame (A1) and lock it in folded position with the Pull Pin (D2). And, folding down the Back Cushion
(B25).
NOTE: Make sure the Pull Pin (D2) goes through the holes on both sides of the Rear Frame (A2) and
the tube on the Main Frame (A1).
The safety and integrity designed into the BIKE can only be maintained when the BIKE is regularly
examined for damage and wear. Special attention should be given to the following:
1. Adjust the 8 Section Adjustment Knob (B32) and verify that it functions properly and the resistance
changes.
2. Use a wrench to verify that the pedals are tightened securely. If tightening is required, remember that
the left pedal has left hand threads and is tightened by turning counterclockwise.
3. Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts.
Tighten loose nuts and bolts.
4. It is the sole responsibility of the user/ owner to ensure that regular maintenance is performed.
5. Worn or damaged components shall be replaced immediately or the BIKE removed from service until
repair is made.
6. Keep your BIKE clean by wiping it off with an absorbent cloth after use.

OPER
A
TIONALINSTRUCTIONS
UPRIGHT ADJUSTMENT
Refer to the illustrations below.
The angle of the Meter (B10) can be set to different angles from Position 1 to Position 5.
Lift the Lever cover (B6) up using your right foot, adjust the UPRIGHT (A3)/ Meter (B10) to
desired position. Then press the Lever cover (B6) down to lock the UPRIGHT (A3)/ Meter
(B10) in position.

T
OCO
N
T
ACTCUS
T
OMERSERVICE
17

T
OCO
N
T
ACTCUS
T
OMERSERVICE
18
PARTS LIST
A. Welding Parts
No.
Description
QTY
A1 Main Frame 1
A2 Rear Frame 1
A3 Upright 1
A4 Table Support 1
A5 Front Stabilizer 1
A6 Seat Support 1
A7 Back Support 1
A9 Back Frame 1
A10 Rear Stabilizer 1
A11 Lever 1
A12 Magnetic Bracket 1
A13 Folding Axis 1
B. Plastic Parts
No.
Description
QTY
B1 Left Chain Cover 1
B2 Right Chain Cover 1
B3 Middle Cover 1
B4 Left Front Cover 1
B5 Right Front Cover 1
B6 Lever cover 1
B7 Hollow Cap 1
B8 Table Holder 1
B9 Table Holder Support 1
B10 Desktop 1
B11 Bottom Cap 2
B12 Sensor Bracket 1
B13 Bushing 1
B14 Plastic Bushing 6
B15 Oval Plug (20mm x 40mm) 2
B16 Plastic Washer Φ8.5*Φ20 2
B17 Rubber Cushion 1
B18 Leveling Cap 2
B19 Wheel 2
B21 Tube Bushing S30*30 1
B22 Tube Bushing S15*30 4
B23 Bumper 1
B24 Seat 1
B25 Back Cushion 1
B27 Left Pedal 1
B28 Right Pedal 1
B29 Left Crank 1
B30 Right Crank 1
B31 Crank Cap 2
B32 Adjustment Knob 1
B33 Adjustment Knob Bracket 1
B34 Line Clip 2

T
OCO
N
T
ACTCUS
T
OMERSERVICE
19
B35 Plastic Washer Φ10.2*Φ14 2
B37 Stopper 1
B38 End Cap 2
B39 Bearing Housing 2
B40 Hand grip 4
B44 Plug 1
C. Electrical parts
No.
Description
QTY
C1 Meter 1
C2 Connection Wire 1
C3 Folding Axis 1
C5 Left Crank 1
C6 Flywheel 1
C7 Flywheel 1
C8 V-ribbed Belt (230J) 1
C9 V-ribbed Belt (240J) 1
C10 Pulley W/Shaft 1
C11 Pulley Shaft 1
C12 Pulley 1
C13 Sensor 1
C14 Ball Bearing (6000ZZ) 2
C15 Ball Bearing (6200ZZ) 1
C16 Ball Bearing (6003ZZ) 2
C17 Idler Shaft 1
C18 Magnet 6
C19 Idler Shaft 1
C20 Magnet 1
C21 Pulse Sensor 4
C22 Hand pulse Line 1
D. Hardware
No.
Description
QTY
D1 Adjustment Knob 2
D2 Ball Pin 1
D3 Wrench 1
D4 Allen Wrench 1
D5 Carriage Bolt M8X60 4
D6 Hex Head Bolt M6X45 2
D7 Hex Head Round Bolt M8X40 4
D8 Carriage Bolt M8X48 2
D9 Hex Head Round Bolt M8X75 1
D10 Hex Head Round Bolt M8X20 2
D11 Eye Bolt M6 2
D12 Hex Head Bolt M8X55 2
D13 Hex Head Round Bolt M8X68 1
D14 Hex Head Round Bolt M8X12 3
D15 Screw, Round Head Self-Tapping ST4.2X16 17
D16 Bolt, Round Head M5X20 4
D17 Bolt, Round Head M6X12 10
D19 Wave Washer S10 1

T
OCO
N
T
ACTCUS
T
OMERSERVICE
20
D20 Screw, Round Head Self-Tapping ST4.2X25 2
D21 Flange Nut M10 x 1.25 2
D22 Acorn Nut M8 4
D23 Arc Washer M8 4
D24 Washer M8 11
D25 Nylock Nut M8 7
D26 Nut M10 2
D27 U-Shape Bracket 2
D28 Nylock Nut M6 2
D29 C Ring Φ17.0 6
D30 C Ring Φ10 2
D31 Wave Spring Washer S17 1
D32 Spring Washer (M8) 3
D33 Large Washer (ø8.2 x ø25 x 2mm) 2
D34 Nut M10 1
D35 Carriage Bolt M4X10 1
D36 Nylock Nut M10 1
D37 Nylock Nut M8 2
D38 Washer M8 3
D39 Nylock Nut (M6) 2
D40 Screw, Round Head Self-Tapping ST4.0X10 2
D41 Bearing Housing Cover 2
D42 Spring 1
D43 Bolt M5X55 1
D44 Washer (M5) 1

GARLANDO SPA
Via Regione Piemonte, 32 - Zona Industriale D1
15068 - Pozzolo Formigaro (AL) - Italy
www.toorx.it - [e-mail]