Toro Multi-Pro 5800 User manual

FormNo.3394-879RevA
StepKit
Multi-Pro5800TurfSprayer
ModelNo.130-8230
ModelNo.130-8231
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
Figure1
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescriptionQty.Use
Spacerbracket1
Stepmount(Model130-8231)1
Hex-headbolt(1/2x6inch)1
Locknut(1/2inch)1
1
Washer(1/2inch)1
Installtheleftstepmount.
Spacerbracket1
Stepmount(Model130-8230)1
Hex-headbolt(1/2x6inch)1
Locknut(1/2inch)1
2
Washer(1/2inch)1
Installtherightstepmount.
Step1
Hex-headbolt(1/4x2-1/4inch)2
Flangenut(1/4inch)2
3Washer(1/4inch)2
Installthestep.
©2015—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3394-879*A

1
InstallingtheLeftStepMount
(Model130-8231)
Partsneededforthisprocedure:
1Spacerbracket
1Stepmount(Model130-8231)
1Hex-headbolt(1/2x6inch)
1Locknut(1/2inch)
1Washer(1/2inch)
Procedure
1.Atthefrontofthemachine,aligntheholesinthe
spacerbracketwiththeholesinthefrontframetube
(Figure2).
Figure2
1.Locknut(1/2inch)4.Stepmount
2.Spacerbracket5.Washer(1/2inch)
3.Front-frametube6.Hex-headbolt(1/2x6
inch)
2.Aligntheholesinthestepmountwiththeholesinthe
spacerbracketandtheframetube(Figure2).
3.Securethestepmountandthespacerbrackettothe
frametubewithahex-headbolt(1/2x6inch),lock
nut,andwasher(Figure2).
4.Torquethenutandboltto91to123N-m(67to83
lb-ft).
2
InstallingtheRightStepMount
(Model130-8230)
Partsneededforthisprocedure:
1Spacerbracket
1Stepmount(Model130-8230)
1Hex-headbolt(1/2x6inch)
1Locknut(1/2inch)
1Washer(1/2inch)
Procedure
Performsteps1through4from1InstallingtheLeftStep
Mount(Model130-8231)(page2)fortherightstepmount
(Model130-8231).
2

3
InstallingtheStep(Model
130-8230or130-8231)
Partsneededforthisprocedure:
1Step
2Hex-headbolt(1/4x2-1/4inch)
2Flangenut(1/4inch)
2Washer(1/4inch)
Procedure
1.Alignthe2holesinthestepwith2oftheholesinthe
endofthestepmount(Figure3).
Note:Youcaninstallthestepin1of5positionsto
bestsuityourpreference.
Note:Usetheouter-holepositionwhenthemachine
isequippedwiththecaboption.
Figure3
1.Hex-headbolts(1/4x
2-1/4inch)
4.Step
2.Washer(1/4inch)5.Flangenut(1/4inch)
3.Stepmount
2.Securethesteptothestepmountwith2hex-head
bolts(1/4x2-1/4inch),2angenuts,and2washers
(Figure3).
3.Torquetheboltsto1017to1243N-cm(90to110
lb-in).
3