Westomatic primo MINI User manual

SERVICE MENU
MINI/MIDI
MINI/MIDI

SERVICE MENU
The service menu allows
engineers to access drink and
machine settings.
01. INGREDIENTS
02. RECIPES
03. SETTINGS
04. COUNTERS
05. SERVICE NOTIFICATIONS
06. HARDWARE
07. ERROR MESSAGES
08. SOFTWARE
09. CHANGE PIN CODES
10. RINSE & CLEAN MESSAGES

1.INGREDIENTS
You can customise your machine
to suit your requirements using
the service menu.
Selection 1 is for canister content
and calibration.
01. CANISTER CONTENT
02.INGREDIENT CALIBRATION
03. CANISTER EMPTY SIGNALLING

3 options to choose
from:
Canister Content,
Ingredient calibration,
almost empty?
01. CANISTER CONTENT
Each instant product
has its own specific
weight. These must be
set to use the empty
signal.
02. INGREDIENT
CALIBRATION
Calibration must be
done to ensure correct
product dispense.
The rest weight counts
down after each drink
dispensed. When it
reaches 0 the drink
will not dispense.
Select ingredient, the
estimated weight is
shown.
Place an empty cup on
the scales and press
Tare.

11
Hold the cup under the
canister chute and
press ACTIVATE. Collect
the ingredient, and
repeat 2 more times.
Weigh the ingredients
and divide by 3.
Correct the measured
weight from the
selected product
canister and press
SAVE.
03. ALMOST EMPTY
SIGNALLING
Activate the canister
empty - ON/OFF
Ingredient Almost out:
- levels at 20%
Ingredient out: - levels
at 10% (recipes are
disabled)
When switched ON, an
extra button is shown
at the top of the
screen. Press the
button to open
canister refill screen
12

13
Fill the canisters up completely.
Select the canister you filled up by pressing
the picture. Swipe to reach all canisters.
Press confirm refill button to SAVE the
canister refill.
Relevant recipes are enabled again.

2.RECIPES
This section allows you to set up
drink recipes.
01. POSITION SCREEN - used to
assign recipes to the desired
screen position.
02. QUICK RECIPE PRO - fine tune
your drink, cup volume, taste
strength etc
03. RECIPE OPTIONS - additional
settings, like prices, multi-cup,
recipe name etc
04. RECIPE SETTINGS - access to
all the recipe parameters

01. POSITION SCREEN.
This allows you to assign
a recipe to a screen
position.
Select a screen - swipe
to screen 1, 2 or 3.
Select an empty
position (+)
The recipe is then
assigned to the selected
screen position 8.
Select a recipe from
the list and press ADD
to confirm.
*scroll the list up and
down to find your
recipe
To remove a recipe -
select the recipe you
want to remove.
Press REMOVE.
Then press SAVE to
accept the changes

11
Select the drink you
want to fine tune.
02. QUICK RECIPE PRO
Set +/- here:
COFFEE (gr)
TOPPING (gr)
CUP VOLUME (ml)
TEST the drink
SAVE settings
(screen 2)
DISTRIBUTION WATER
TEST the drink
SAVE settings
MIXER SPEED
Speed 1 = start speed
Speed 2 = end speed
Speed Ratio = ratio speed
1&2
03. RECIPE OPTIONS
Use this option to set
special options per
recipe.
TEST your recipe
SAVE your settings
12

RECIPE ACTIVE - sliding
ON/OFF
RECIPE DISABLED -
recipe button does not
work, and recipe button
is dimmed dark.
CUP VOLUME & PRICE
Number of cup sizes per
recipe (3 max)
Cup volume (small -
normal - big)
Price high - normal price
Price Low - discount
price (for special times
of day/week)
Test - recipe/cup sizes
Save - settings
13
14
15
Activate the Cup Size
function to use different
cup/jug sizes
16
2 Cup sizes -
normal/large
3 Cup sizes -
small/normal/large
2 jug sizes - 1/2 &
Full
17
A jug recipe is a recipe
which is repeated. The
jug volume = cup volume
x multicup.
18

Jug dispensing options:
PIN code 11111
Jug volume/coffee
strength adjustment slide
Leak out time - the time
that the product
continues to run out of
the mixer. After this time
a new drink selection
can be made.
Push & Hold (On/Off)
The drink is only
dispensed when the
recipe button is pressed.
Only for Hot & Cold
water.
19
20
21
Allergens Info.
Per recipe user can be
warned about Lactose/
Soy/Gluten/Wheat. Info
displayed after recipe
screen.
Now ACTIVATE this
function. Select the
Operator menu,
05. SOUND & VISION.
Select the ingredients
you want to display.
SAVE the settings
Repeat this with each
recipe.
24
22
23

05. ALLERGENS INFO
Slide to switch on,
SAVE changes
05. ALLERGENS INFO
The start screen shows
you in orange text the
ingredients you selected.
POSITION LOGO ON CUP
Use to reposition your
own cup logo.
25
26
27
POSITION LOGO ON CUP
Horizontal / vertical
position adjustment
SAVE settings
ALTERNATIVE RECIPE
NAME.
Select left side to show
keyboard. Active switch
on and SAVE changes.
30
28
29
For capitals
For small letters
?!# to use symbols
To create second line
123 to use numbers
SAVE settings

ALTERNATIVE RECIPE
NAME:
CAPPUCCINO SPECIAL
Extra Long
LOAD DEFAULTS
Select this if you want to
load factory recipe.
You will loose all
personal settings.
RECIPE OPTIONS
Referral recipes - to
activate recipe option
ADDITION SUGAR MILK.
Switch ON
SAVE settings
REFERRAL RECIPES
Select the recipe COFFEE
Selecting milk/sugar
strength option the recipe
automatically changes
into COFFEE MILK/SUGAR
LOAD DEFAULT VALUES
Select this item to reset
your personal settings.
Personal settings will be
lost.
31
32
33 36
34
35
Yes to confirm
No to exit out without
loading settings.

UNIT 1/2/3
Dosing Valve
Delay time - water
supply towards
mixer
Dosing Valve -
dispensed water
volume to Mixer.
When drink uses
water from diff. units -
must always be 100ml
COFFEE DELAY TIME -
time before ingredient
starts.
STEPS - pause in
ingredient dispense
SUGAR DELAY TIME -
before ingredient
dispense starts
STEPS - pause in
ingredient dispense.
04. RECIPE SETTINGS
All the parameters for
"building" the perfect
drink. All parameters
based on 100ml drink
37
38
39 42
40
41
MIXER SETTINGS
Mixer delay - time
before mixer starts.
Running time mixer -
time miser runs for a
drink 100ml

OTHER VALUES:
Hot water / cold
water delay times.
INGREDIENT RANGE
Adjust percentage
volumes of drinks in
each drink.
Speed 1 - start speed
Speed 2 - end speed
Speed Ratio - ratio
speed 1 & 2
Test your drink
SAVE settings
43
38
39

3.SETTINGS
You can adjust the settings to suit
your requirements using the
SETTINGS menu.
01. LANGUAGE
02. TEMPERATURE
03. DISPLAY
04. FAN
05. PAYMENT & TELEMETRY
06. OPERATOR SETTINGS
07. DEMO MODE
08. DRIP TRAY SIGNAL
09. GENERAL RECIPE OPTIONS
10. DEALER INFO

01. LANGUAGE
Select the language and
press SAVE.
02. TEMPERATURE
Temp boiler - Set boiler
temp 85°C
Dispense release - Set
boiler temp to allow
dispense again 83°C
Stand-by Temp - factory
setting is OFF. Boiler
temp during stand-by.
Extended Heating time -
factory setting 5 sec.
Dispense blocking - set
boiler temp disables
dispensing 78°C
Hysteresis - if the temp
drops, what point the
boiler reheats 0°C
03. DISPLAY
Show clock - ON/OFF
Daylight Saving - ON/OFF
Time Zone - EU/USA
Time diff - +1 DST
Brand Name display - can
write own name and
display it
Time finished - 0ff 2-5 sec
Recipe Icon - Normal/
large.

11
04. FAN
Speed during rest - 61%
(off / 40-100%)
Speed recipe
preparation - 76%
(40-100%)
Running time after
preparation - 60sec (0-
300sec)
05. PAYMENT &
TELEMETRY
General Settings
Visualisation
Telemetry
General Settings:
Payment System
connected - ON/OFF
External Release -
ON/OFF
Purchase Obligation -
ON/OFF
PRE PAY - ON/OFF
Cash & Card - ON/OFF
Single Vend - ON/OFF
Show Credit - ON/OFF
Payment Status:
Free/paid
Decimal position - 2
Cashless payment
timeout - 20sec
Max Coin - £3
12

Add in Dealer Name /
Phone Number / E-mail.
Currency Symbol -
ON/OFF
Position Symbol
before/after amount
SAVE settings
External Release -
ON/OFF
On - informs of an
external release signal
Release Time - 20secs
Visualisation - ON/OFF
When switched on there
will be a second
instruction screen
displayed when selected.
13
14
15
09. GENERAL RECIPE
OPTIONS - ON/OFF
16
Addition Sugar / Milk
Add in the sliders for
the options of milk
or sugar.
Press START
17
18

4.COUNTERS
You can receive audit information
for Cleaning/Rinsing/ Operating
and Recipe dispenses.
01. RINSE HISTORY
02. CLEANING HISTORY
03. RECIPE COUNTERS
04. OPERATING HOURS
05. RESET HISTORY