Westomatic EVOLVE User manual

Technical
Manual
Part Number: 350090

Receiving your Machine1.
Westomatic will deliver your machine and assist with the initial
installation and training.
Your machine will already be set up to your specifications - taken
from your order.
When you receive your machine it's important that you check for
any damage in transit - please report these directly to Westomatic
HQ as soon as possible.
The Evolve is intended to deliver drinks at <5°C into the customers
own reusable bottle.
The water is triple filtered using sediment, UV and 0.1 micron
filters.
Drink options include, but are not limited to Protein powders /
BCAA's / Pre-Workout / Electrolytes / powdered Milkshakes.
This Technical manual provides guidance to operate and clean
your Evolve Nutrition Dispenser.
Version: 1.0 (August 2021)

2. External Features
D I G I T A L M E D I A S C R E E N
I L L U M I N A T E D D R I N K S M E N U
H O V E R S E L E C T B U T T O N S 1 , 2 , 3 , 4
L E D L I T B O T T L E S T A T I O N
S E C U R I T Y T L O C K
R E M O V A B L E S I D E / F R O N T K I C K P L A T E S
L C D D I S P L A Y
C A S H L E S S B L A N K I N G P L A T E
B O T T L E S E N S O R
I R R E M O T E C O N T R O L
F O R M E D I A S C R E E N

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
3. Internal Features
*Also included (but not shown) is a Spare Sanitising bucket and Hygiene kit

4. Water Flow Diagram
24VDC - Controls when
water can enter machine.
Prevents continual mains
water pressure within the
machine
WATER INLET:
Controls incoming water
pressure to the required
flow rate.
Clockwise to increase
Counter-clockwise to
decrease
PRESSURE REGULATOR:
Sterilises the water supply to
remove any bacteria not
removed by the water filters.
Purifies at rate of 1 gallon
per minute
UV WATER FILTER:
Allows you to manually turn
off and isolate water supply.
Helps remove water and
pressure from the system
before changing the filters
Ensure water flush button is
pressed to run water out of
system
STOP VALVE:
Dual water filter removes
sediment / contaminants
down to 5 microns.
Water filter (blue) must be
fitted on the left
WATER FILTER:
Water chiller chills filtered
mains water to deliver cold
drinks between 3°C & 5°C.
WATER CHILLER:
FLOW CONTINUES TO
FLAVOUR DECK

5. Water Flow to Flavour Deck
Turns water on / off.
Allows flow to each
individual flavour.
SOLENOID VALVE:
Powder is dispensed from
canisters into bowl.
Timed water dispense to
assist mixing.
Individual bowls to prevent
cross - contamination.
Easily removed for cleaning.
MIXING BOWLS:
WATER FLOW FROM
CHILLER
4 individual motors.
Single speed mixer
motor to blend drink
in the mixing bowl.
MIXER MOTOR:
Mixer base & seal ensures
water does not leak.
Impeller attached to mixer
motor to blend the drink.
Both can be easily removed
for cleaning.
MIXER BASE & IMPELLOR:
Individual tubes ensure
contamination free drink
dispense.
4 separate nozzles fit into
dispense head.
Both can be easily removed
for cleaning.
DISPENSE TUBE & NOZZLE:

6. Installation
1 . C O M M I S S I O N I N G W A T E R
The Evolve is not suitable for outdoor use or for being jet
washed in any way.
Ensure there is a minimum of 100mm of free space behind
the machine to allow for ventilation of chiller.
The machine must be switched off before you begin.
Connect hose to mains water supply / potable water.
Min water pressure = 0.13-0.84 MPa / 1.4 - 8.4 Bar.
Check filters and fit them to the machine
NB. Sediment filter (blue) must be fitted on the left.
Turn water on and CHECK FOR LEAKS
Plug machine in and power on machine.
Prime filters by flushing water through. Repeat until the
water runs clear and all air is eliminated.

6. Installation
2 . L E V E L L I N G
Locate the machine on a stable, level surface.
You will need a spanner and a spirit level.
Incorrect levelling can lead to misalignment and
inconsistent bottle fill issues.
Using the spanner adjust the foot bolts to raise or lower the
machine.
Ensure you check side to side and front to back to ensure
machine is level in both planes.

6. Installation
3 . F I T T I N G T H E P L I N T H S
The Evolve comes with 2x side plinths, and 1x front - these
are packed up securely inside the machine for delivery.
Locate the machine into place before fitting the plinths.
The nuts will be pre-fitted - and must be facing the front
(ensuring the bolts are closer to the bottom of each plinth).
Plinths will have
nuts fitted
The nuts must be located
closer to the bottom
when fitting
The nuts fit
into a keyhole
connection with
the front plinth

Remove screws
Slide plinth into back
of machine first
Fit plinth to front
Replace screws
Repeat steps on other side
Remove the screws from the front legs of the machine.
Slide plinth into back first.
Fit the plinth to the front ensuring it lines up with holes
Replace screws & repeat on the other side.
1.
2.
3.
4.
F I T S I D E P L I N T H S
6. Installation