Wren Kitchens Vogue BASE UNIT 500 3 Drawer User manual

BASE UNIT
500 3/4 Drawer Assembly Guide
For Internal Use: FI.WR.INS.028_WKIN00109_BASE_500_3_4Drawer_Rev6.indd
500
4 Drawer
500
3 Drawer

Page 1
BASE UNIT
500 3/4 Drawer Assembly Guide
Standard Drawer (Packed Separately)
Fitting Pack Contents
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
DRAWER
COVER CAP
x2
DRAWER
COVER CAP
x2
DRAWER SIDE
x1 Right Hand
DRAWER SIDE
x1 Right Hand
DRAWER SIDE
x1 Left Hand
DRAWER SIDE
x1 Left Hand
DRAWER
FRONT
FIXING
x 2
DRAWER
FRONT
FIXING
x 2
Deep Drawer (Packed Separately)
Fitting Pack Contents
(Y) x2
Gallery
Head
(J) x16
Drawer Runner
16mm Screws
(J) x16
Drawer Runner
16mm Screws
(N) x1
Door Buer
(N) x1
Door Buer
(Q) x4
21mm
Screw
(Q) x4
21mm
Screw
(L) x2
15mm
Screw
METAL BACK
PANEL
x 1
METAL BACK
PANEL
x 1
DRAWER
BASE
x 1
DRAWER
BASE
x 1
DRAWER
RUNNER
x 1 Right Hand
DRAWER
RUNNER
x 1 Right Hand
FRONTAL
(Supplied separately)
FRONTAL
(Supplied separately)
DRAWER
RUNNER
x 1 Left Hand
DRAWER
RUNNER
x 1 Left Hand
GALLERY
RAIL
x 2
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.028_WKIN00109_BASE_500_3_4Drawer_Rev6.indd
Step 2.
Clip on metal back panel to drawer base &
drawer sides.
Step 3.
Screw back panel in position using 2 x 16mm screws (J)
to drawer base in holes provided.
Step 1.
Secure drawer base to drawer side using 4 x 16mm
drawer runner screws (J) in holes provided.
Seat the edge of drawer base tight
into corner of casing, as shown.
The decorative face of drawer base
to be positioned as shown.
Metal back
panel
View from back
Metal
back
panel Drawer base
white
decorative
face up
J
J
J
J
J
J
J
J
J
Decorative
face
Drawer
base
J
Step 4.
Frontal Attachment
Secure drawer side xing clips using 2 x 21mm
screws (Q) in pilot holes provided as shown.
Drawer
base
Fixing
clip
& (Q)
Fixing
clip
& (Q)
Standard
drawer
Step 6.
Fit Drawer Cover Caps
over drawer side adjustment.
Drawer
Cover Cap
Drawer
frontal
Drawer side
J
Fixing
clip
Drawer side
xing clip
Q
Q
Drawer
frontal
Repeat step 1 so both drawer
sides are attached to drawer base.
View of drawer side
1
3
2b
2a
Step 5.
Draw Adjustment
Screw point 1as shown
to adjust drawer
frontal right & left.
Screw point 2a as
shown to adjust
drawer frontal
up & down.
Tighten 2b
once in position.
Releasing xing clip. Screw
point 3whilst applying
downward pressure as
shown to release.
Front of drawer

Page 3
BASE UNIT
500 3/4 Drawer Assembly Guide
Fixing
clip
& (Q)
Fixing
clip
& (Q)
2
1
Y & L Y & L
Step 6.
Fit Gallery Rail into the top
corners of Metal Back Panel.
Locate front end of the
Gallery Rail into the opening
of the gallery Head, which
is secured to the frontal as
shown
Deep
drawer
J
JMetal
back
panel
Drawer base
white decorative
face up
Fixing clip
(Y) Gallery
Head
Drawer side
xing clip
Q
Q
Drawer
frontal
Drawer
side
Drawer
frontal
Step 7.
Fit Drawer Cover Caps
over drawer side adjustment.
Drawer
Cover Cap
Step 2.
Clip on metal back panel to drawer base &
drawer sides.
Step 3.
Screw back panel in position using 2 x 16mm screws (J)
to drawer base in holes provided.
Step 1.
Secure drawer base to drawer side using 4 x 16mm
drawer runner screws (J) in holes provided.
Seat the edge of drawer base tight
into corner of casing, as shown.
The decorative face of drawer base
to be positioned as shown.
View from back
Metal
back
panel
Front of drawer
Decorative
face
Drawer
base
J
J
JJ
JJ
Drawer
base
J
Repeat step 1 so both drawer
sides are attached to drawer base.
JJ
Step 5.
Draw Adjustment
Screw point 1as shown to
adjust drawer frontal
right & left.
Drawer Frontal
Adjustment
Screw point 2a
as shown to adjust
drawer frontal up & down.
Tighten 2b
once in position.
Releasing
xing clip.
Screw point 3
whilst applying
downward pressure
as shown to release. View of drawer side
13
2b
2a
Step 4.
Frontal Attachment
Secure drawer side xing clips using 2 x 21mm screws (Q)
&Gallery Head (Y) using 1 x 15mm screw (L) in pilot holes
provided as shown.

Page 4
For Internal Use: FI.WR.INS.028_WKIN00109_BASE_500_3_4Drawer_Rev6.indd
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
Panel A
x1 Back Panel
Panel B
x2 End Panel
Panel E
x2 Rail Panel
Panel C
x1 Base Panel
(F) x12
Wooden
Dowel
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x7
30mm
Screw
(L) x28
15mm
Screw
(M) x4
Cover Cap
L Bracket LGE
x2
Space Plug
x1
500 Drawer Unit Contents
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 5
BASE UNIT
500 3/4 Drawer Assembly Guide
3 drawer
4 drawer
Step 1.
To attach drawer runner, screw into end panels (B) using 2 x 16mm
screws (J) per drawer rail, into pilot holes provided, 3rd hole from
front, as shown.
B
B
646mm
74mm
74mm
503mm
360mm
646mm
360mm
J
J
From Front
From Front
From Bottom
From Bottom
JJ
B
B

Page 6
For Internal Use: FI.WR.INS.028_WKIN00109_BASE_500_3_4Drawer_Rev6.indd
Step 4.
Attach panels (C) & (E) to panels (B),
using cam dowel (G) (in blue),and also
using dowels (F) (in orange) in positions
as shown.
Step 5.
Insert cam lock (H).
Do NOT tighten until Step 7.
NB. All cam locks (H) are to be positioned facing the
outside of the unit e, for ease of tightening. Do not use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
G GF
FG
GF
F
FF
FF
GG
FF FF GG
BB
B
B
E
C
B
B
C
C
View from underside View from underside
H
G
G
H
Step 2.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
Step 3.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
Seat (G)
cam dowel
into hole as
shown.

Page 7
BASE UNIT
500 3/4 Drawer Assembly Guide
Step 6.
Slide back panel (A) into
groove of end panels (B).
Once back panel (A) is in position, ensure
the panel is ush & square with bottom of
end panels (B).
Step 7.
Hand tighten all cam locks (H), this will
expand cam dowels (G) and tighten the
unit together.
Step 8.
Ensure unit is square. Secure back panel (A)
with 3 x 30mm screws (K) equally spaced at
the bottom of back panel (A) into
base panel (C), as shown.
Ensure you screw into the centre of base
panel (C) (9mm from bottom edge).
B
C
B
E
A
C A
K
K
K
9mm

Page 8
For Internal Use: FI.WR.INS.028_WKIN00109_BASE_500_3_4Drawer_Rev6.indd
Step 9.
Position legs as shown. Ensure legs are rotated to
also provide support to the end panels (B).
B
B
Front Front
C
Leg position diagram
Step 10.
Secure each of the legs into place with 4 x 15mm screws (L)
per leg.
L
L
L
L
B
C
B
Step 11.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning unit upright. Once in situ
level accordingly.
C

Page 9
BASE UNIT
500 3/4 Drawer Assembly Guide
Use 2 x 15mm screws (L) to secure each
of the L brackets LGE to the unit at either side.
Then screw up through into the worktop as
shown.
Screw up through the front rail into your worktop to secure it in place.
L
L
Screw into any side units using the 30mm screws (K) provided to secure to
the unit. Screw just to the rear of the indentations at the top and bottom on
sides of the unit where applicable. Place a cover caps (M) on the head of the
screws to conceal them. K
Screws for attaching to walls and worktop are not provided as these vary depending
on materials, thickness and construction. Ensure appropriate xings for wall and
worktop construction are used. Please refer to the specialist worktop supplier if
these are required for solid surface worktops.
Drill pilot holes through the back rail into the wall and
insert wall plugs. Then unwind space plugs until it
contacts both surfaces. Finally, tighten the screws.