Wren Kitchens Vogue WALL UNIT 600 Lift User manual

WALL UNIT
600 - 800 Lift Assembly Guide
For Internal Use: FI.WR.INS.032_WKIN00121_WALL_600_800_Lift_Rev7
288 x 600
360 x 600
288 x 800
360 x 800

Page 1
WALL UNIT
600 - 800 Lift Assembly Guide
Panel A
x1 Back Panel
Hanging Bracket
X2 Inc Screws
(F) x8
Wooden
Dowel
REQUIRED TOOLS
NOT to be
used with
CAM DOWEL
& CAM LOCK
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x4
30mm
Screw
(L) x8
15mm
Screw
(S) x4
20mm
Screw
(M) x8
Cover Cap
(N) x1
Door
Buer
(T) x10
Back Panel
Support Clip
Hanging Bracket
Plate
X2 (Screws Not
Included)
Hinge Mounting
Plate X2 Inc Screws
Hinge
X2 Inc Screws
Corner
Gusset
X2
Hanging Bracket
Cover Cap
X2
Lift Hinge
X2 Inc Screws
Panel B
x2 End Panel
Panel C
x2 Base Panel
Frontal
(packed separately)
x1
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.032_WKIN00121_WALL_600_800_Lift_Rev7
Step 3.
Attach panels x2 (C) to panel
(B), using cam dowels (G)
(in blue) and also using
dowels (F) (in orange) in
positions as shown.
Step 4.
Slide panel (A) into the groove
of panels (B) and x 2 (C).
Step 5.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the
cam dowels (G) and tighten
the unit together.
All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
G
G
F
F
F
F
G
G
B
A
C
C
B
BB
CC
H
H
G
G
View from underside View from underside
Step 1.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
Step 2.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
Seat (G)
cam dowel
into hole as
shown.

Page 3
WALL UNIT
600 - 800 Lift Assembly Guide
Step 8.
Attach panel (B) to panels
(C) using cam dowels (G)
(in blue) and also using
dowels (F) (in orange) in
positions as shown. Ensure
panel (A) is seated into the
groove of panel (B).
Step 9.
Cam Lock (H)
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the
cam dowels (G) and tighten
the unit together.
All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
Seat (G)
Cam Dowel
into hole as
shown.
G
G
F
F
F
F
G
G
B
BB
CC
H
H
G
G
View from underside View from underside
B
B
A
C
H
H
C
G
G
Step 6.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
Step 7.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.

Page 4
For Internal Use: FI.WR.INS.032_WKIN00121_WALL_600_800_Lift_Rev7
Step 11.
Slide the back panel clips (T) into the groove of both panels (B) & (C). The back panel clips (T) should be evenly
spacedasshownandpositionedtoallowthehangingbracketandcornergussetstobetted.Onceinplace,
tighten screw.
The side back panel Clips should be disregarded for the 288 units.
Step 10.
Ensure unit is square.
BA
C
A
T
A
T

Page 5
WALL UNIT
600 - 800 Lift Assembly Guide
Step a
Insert Hanging
Bracket into pre-drilled holes
Step c
Secure with provided
2 x 20mm screws (S) per bracket
Step b
Rotate locking
lever 180 degrees
Detail A Detail A
S
S
Detail A
Step 12. Hanging Brackets steps a,b & c to be carried out on both sides as shown
A
B
Step 13.
Secure corner gussets to the bottom left and right hand
side of the wall unit using 4 x 15mm screws (L) per plate.
LL
LL
Detail B
View though
Back Panel
Pilot
hole
M
Detail B
Step 14.
Drill a small pilot hole through the centre of the Corner
Gussets. Use this hole at the end of the process to screw
through and into the wall. Cover the screw heads using the
cover caps (M) provided.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction. Ensure
appropriate xings for wall constructions are used.

Page 6
For Internal Use: FI.WR.INS.032_WKIN00121_WALL_600_800_Lift_Rev7
18mm
50mm
35mm
18mm
50mm
35mm
TOP FIXED SHELF
INSIDE FACE
C
Front
92mm 92mm
Shaker
5 Piece
Frontal
ONLY
Shaker
5 Piece
Frontal
ONLY
Step 15.
Measureandattachhingemountingplateontoxedshelf(C) as shown, using screws which are already
positioned within the hinge plates.
Step 16.
Measure and attach lift hinge
brackets with 2 x screws per
brackets. The required screws are
included inside lift hinge pack.
Step 19.
Secure hinges by tightening 2 x screws with hinge dowels attached. These are
already positioned within the hinges.
Step 18.
Insert hinges into holes provided.
142142
110110
BackBack
Left
Right 3030
FRONTAL
Removed from lift hinge
B
B
C
Step 17.
Measure and attach lift hinge brackets to the frontal with 2 x screws per bracket.
The required screws are included inside lift hinge pack.
192 192
160 160
Top Top
Front Front
37 37
LEFT HAND RIGHT HAND
B B
Hinge Plates
MEASUREMENTS
FROM INSIDE OF
UNIT

Page 7
WALL UNIT
600 - 800 Lift Assembly Guide
Care to be taken. Hanging procedure is necessary for a safe installation.
Step 20.
Measure appropriately and
attach the 2 x hanging bracket
plates onto the wall screwing
through the provided holes into
your wall.
Step 21.
Hang the unit using the
brackets to hook onto the
plate as shown
Hanging Bracket
Plate
Step 22.
Using points a, b & c adjust the unit to suit.
Step a.
Rotate the screw clockwise
to move the unit up.
Anti-clockwise for down.
Step b.
Adjust the depth using
centre screw.
Step c.
Screw the red screw until it
touches the plate to lock
in position.
Hanging
Bracket
viewed through
Back Panel
b
C
c
a
a
b
KStep 23.
Screw into any side units using the provided 2x 30mm screws (K) to secure the
unit. Screw just to the rear of the hinge plate then place a cover cap (M) on the
head to conceal it.
Screws for attaching to walls are not provided as these vary depending on materials,
thicknessandconstruction.Ensureappropriatexingsforwallconstructionareused.

Page 8
For Internal Use: FI.WR.INS.032_WKIN00121_WALL_600_800_Lift_Rev7
Step 24.
Clip hinges into hinge mounting plates on
the unit.
Step 25.
Clip lift hinge mechanisms into each
bracket.
Step 26.
Use a 4mm allen key to adjust
the strength of the lift hinge for
the door weight.
Hinge Cover Caps
Step 27.
Fit cover caps to hinge. Adjust Softclose to suit.
The left and right hinges MUST be adjusted to the
SAME STRENGTH.
The top and bottom hinges
MUST be adjusted to the
SAME STRENGTH.
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1-In-Out
Point 2- Left - Right
1
2
FRONTAL HINGE
ADJUSTMENT
View from Inside of unit
To release door,
pull catch as shown,
to release hinge from
the hinge plate.

Page 9
WALL UNIT
600 - 800 Lift Assembly Guide