Wren Kitchens TOWER UNIT User manual

TOWER UNIT
84”, 90” & 96”
Diag Corner Larder
with Wine Rack Cabinet
Assembly
Guide
For Internal Use: CON.INS.004.001_50-WKIN00007_TOWER45WineRack_Assembly_Rev3.indd
96” x 24”
84” x 24”
2 Door
70/30 Door
90” x 24”

TOWER UNIT
84”, 90” & 96”
Diag Corner Larder
with Wine Rack Cabinet
Assembly
Guide
Page 1
For Internal Use: CON.INS.004.001_50-WKIN00007_TOWER45WineRack_Assembly_Rev3.indd
(J) L Bracket SML
x6
(K) L Bracket LGE
x4
(B) x142
5/8”
Screw
(H) x6
1 1/4”
Screw
(S) Door Buer
x4
(O) Metal Shelf Peg
x56
Toe Kick Attachment
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Carcase RH
Right Hand
Carcase LH
Left Hand
Panel (Z)
x1 Top Panel
Frontals
2Dr or 70/30
Frontal
Toe Kick
x2
Cabinet
Toe Kick
x1
Hinge Mounting Plate
Inc Screws
Hinge
Inc Screws
Fixing Plate (Ff)
x19
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
70/30
OPTION
2Dr
OPTION
(Packed Seperately)
Legs
x10

Page 2
TOWER UNIT
84”, 90” & 96”
Diag Corner Larder
with Wine Rack Cabinet
Assembly
Guide
For Internal Use: CON.INS.004.001_50-WKIN00007_TOWER45WineRack_Assembly_Rev3.indd
RH
Fixing Plate diagram
View from Above
14 3/8”
6 11/16”
OUTSIDE
FACE
Z
Front
Step 1.
Lay both carcases LH & RH at as shown.
Secure 5 x xing plate (Ff) positioned onto outside
face of panel (Y) of carcase RH equally spaced
using 2 x 5/8” screws (B) as shown.
Step 2.
Using 2 x 5/8” screws (B) per plate secure
2 x xing plate (Ff) positioned onto outside
face of panel (Z) of carcase RH using
measurements shown.
B
B
B
B
Ff
View from above
Carcase RH
View from above
Carcase RH
Z
Y
Z
RH
LH Y
Ff
Z
Ff

TOWER UNIT
84”, 90” & 96”
Diag Corner Larder
with Wine Rack Cabinet
Assembly
Guide
Page 3
For Internal Use: CON.INS.004.001_50-WKIN00007_TOWER45WineRack_Assembly_Rev3.indd
Step 3.
Secure leg base into place with
2 x 5/8” screws (B) per leg as shown.
Ensure legs are rotated to also provide
support to the end panels (Y).
Front legs should have at edge to the
front.
B
Step 5.
Push leg rmly down into leg base.
Adjust legs to 4 1/2” before turning both carcase upright.
Once in situ level accordingly.
It is important to lift unit onto its legs. Do
not tilt as depicted in image.
X
YY
Front
RH X
FrontFrontFront
LH X
Leg position diagram
View From Underside
Y
B
Step 4.
Lightly hit centre peg of leg
base with hammer until ush.
X
Y
X
Y

For Internal Use: CON.INS.004.001_50-WKIN00007_TOWER45WineRack_Assembly_Rev3.indd
Page 4
Step 6.
Position carcase LH and carcase RH together as shown.
Ensure carcases are ush & square.
View from rear of unit
Step 8.
Align 2 x L bracket SML (J) combined with
2 x 5/8” screws (B) per bracket as shown.
Secure carcase from inside the cabinet as shown.
Step 7.
Screw through xing plate (Ff)
into adjoining carcase LH using
2 x 5/8” screws (B) to secure both
carcases together.
Repeat per xing plate (Ff).
L
B
B
TOWER UNIT
84”, 90” & 96”
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide
Ff
Ff
Ff
Ff
Ff
Ff
Ff
LH
RH
Front
Front
Front
LH
RH
LH
RH
BB
BB
B
B
Ff
Ff
Ff
Ff
Ff
J

TOWER UNIT
84”, 90” & 96”
Diag Corner Larder
with Wine Rack Cabinet
Assembly
Guide
Page 5
For Internal Use: CON.INS.004.001_50-WKIN00007_TOWER45WineRack_Assembly_Rev3.indd
Step 9.
Use 2 x 5/8” screws (B) to secure each of the
4 x L brackets LGE (K) to both carcases positioned as shown.
B
B
Step 10.
Screw through into the wall as shown.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction.
Ensure appropriate xings for wall constructions are used.
K
Fixings
to Wall
Front Front

For Internal Use: CON.INS.004.001_50-WKIN00007_TOWER45WineRack_Assembly_Rev3.indd
Page 6
Step 11.
When combined cabinet is secured in position, attach top Panel (Z),
using 4x xing plates (Ff) combined with 4 x 5/8” screws (B) per plate,
positioned as shown.
Step 12.
Measure toe kick and cut to suit the width of carcase (LH) and again for (RH).
Mark clip positions by aligning toe kick sections to legs. Use 2 x 5/8” screws (B) as shown to x clip to toe kick.
Detach the leg clip from the toe kick clip. Slide leg clip into toe kick clip as shown.
Top Panel Z
Ff & B
Ff & BFf & B
Ff & B
Toe Kick
Toe Kick
Leg
Brace
BB
Step 13.
Secure plinth by pushing clip rmly onto legs, as shown.
Toe Kick
Toe Kick
TOWER UNIT
84”, 90” & 96”
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide
LH RH
INSIDE
FACE

For Internal Use: CON.INS.004.001_50-WKIN00007_TOWER45WineRack_Assembly_Rev3.indd
TOWER UNIT
84”
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide
Page 7
70/30
HINGE
POSITION
70/30 2 Dr
Door
YY
From Bottom From Bottom
From Top From Top
2 Door
HINGE
POSITION
BB
BB
B
B
B
B
B
B
B
B
B
BB
B
B
B
76 7/16”
26 15/16”
34 3/16”
55 5/16”
45 11/16”
41/4”
75 3/16”
25 11/16”
32 15/16”
54 1/16”
44 7/16”
3”
Step 14.
Attach hinge plates onto end panels (Y) to suit as
shown using 2 x 5/8” screws (B) included per plate.
Hinge side to be mounted in accordance to
customer kitchen plan.
Front Front
76 7/16”
75 3/16”
41/4”
3”
35”
33 3/4”
YY
INSIDE
FACE
INSIDE
FACE

For Internal Use: CON.INS.004.001_50-WKIN00007_TOWER45WineRack_Assembly_Rev3.indd
Page 8
70/30
HINGE
POSITION
70/30
Y
YY
B
B
B
B
B
B
B
B
B
B
82 7/16”
32 15/16”
57 1/16”
26 15/16”
81 3/16”
34 3/16”
58 5/16”
25 11/16”
w
TOWER UNIT
90”
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide
From Bottom
From Top
Front
Step 14.
Attach hinge plates onto end panels (Y) to suit as
shown using 2 x 5/8” screws (B) included per plate.
Hinge side to be mounted in accordance to
customer kitchen plan.
2 Door
HINGE
POSITION
B
B
B
B
B
B
B
48 11/16”
47 7/16”
Y
From Bottom
From Top
Front
2 Dr
Door
B
41/4”
3”
41/4”
3”
82 7/16”
81 3/16”
36 3/4”
38”
INSIDE
FACE
INSIDE
FACE

For Internal Use: CON.INS.004.001_50-WKIN00007_TOWER45WineRack_Assembly_Rev3.indd
TOWER UNIT
96”
Diag Corner Larder
with Wine Rack Cabinet
Assembly Guide
Page 9
70/30
HINGE
POSITION
70/30 2 Dr
Door
YY
From Bottom From Bottom
From Top From Top
2 Door
HINGE
POSITION
B
B
B
B
B
B
B
B
88 7/16”
26 15/16”
34 3/16”
61 5/16”
51 11/16”
41/4”
87 3/16”
25 11/16”
32 15/16”
60 1/16”
50 7/16”
3”
Step 14.
Attach hinge plates onto end panels (Y) to suit as
shown using 2 x 5/8” screws (B) included per plate.
Hinge side to be mounted in accordance to
customer kitchen plan.
Front Front
88 7/16”
87 3/16”
41/4”
3”
B
B
B
B
B
B
B
B
B
B
41”
39 3/4”
YY
INSIDE
FACE
INSIDE
FACE