Wren Kitchens BASE UNIT 600 User manual

WALL UNIT
600 Microwave Assembly Guide
For Internal Use: FI.WR.INS.056.WKIN00123_WALL720_600MW.Rev5

Page 1
WALL UNIT
600 Microwave Assembly Guide
Panel A
x1 Back Panel
Hanging Bracket
x2 Inc Screws
(F) x12
Wooden Dowel
REQUIRED TOOLS
(G) x12
Cam Dowel
(Expanding)
(H) x12
Cam Lock
(K) x6
30mm
Screw
(S) x4
20mm
Screw
(L) x2
15mm
Screw
(M) x4
Cover Cap
(N) x1
Door
Buer
(FF) x2
L Bracket
SML
(T) x4
Back Panel
Support Clip
Hanging Bracket Plate
x2 (Screws Not Included)
Hinge Mounting Plate
x2 Inc Screws
Hinge
x2 Inc Screws
Hanging Bracket
Cover Cap x2
Lift Hinge
x2 inc. Screws
Panel B
x2 End Panel
Panel C
x3 Base Panel
Frontal
(packed separately) x1
NOT to be used
with CAM DOWEL
& CAM LOCK
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.056.WKIN00123_WALL720_600MW.Rev5
Step 1.
Seat dowel (F) into holes in
end panel (B) as shown.
Step 2.
Seat cam dowel (G) into
holes in end panel (B) as
shown.
Step 3.
Attach panels x 3 (C) to
panel (B),using cam dowels
(G) (in blue), and also using
dowels (F) (in orange)
in positions as shown.
Step 4.
Slide panel (A) into the groove
of panel (B).
Step 5.
Insert cam lock (H).
Hand tighten all cam locks (H),
this will expand the
cam dowels (G) and tighten
the unit together.
All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
Seat (G)
cam dowel
into hole as
shown.
B
A
C
C
C
Dowel (F)
& Cam Dowel (G)
location detail
GFF G
B
GFF G
BB
CC
H
H
G
G
View from underside View from underside

Page 3
WALL UNIT
600 Microwave Assembly Guide
Step 9.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the cam
dowels (G) and tighten the
unit together.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
B
A
C
C
C
All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
Step 6.
Seat dowel (F) into holes in
end panel (B) as shown. Step 7.
Seat cam dowel (G) into holes
in end panel (B) as shown.
Step 8.
Attach panel (B) to
panels x 3 (C),using
cam dowels (G)
(in blue), and also
using dowels (F) (in
orange) in positions
as shown.
BB
CC
H
H
G
G
Seat (G)
cam dowel
into hole as
shown.
View from underside View from underside
Dowel (F)
& Cam Dowel (G)
location detail
G
G
F
F
F
F
G
G
B

Page 4
For Internal Use: FI.WR.INS.056.WKIN00123_WALL720_600MW.Rev5
B B
LEFT HAND RIGHT HAND
Step 10.
Ensure unit is square. Secure back panel
(A) with 4 x 30mm Screws (K) as shown.
Ensure you screw into centres of panel
(C) 9mm from the edge
Step 11.
Slide the back panel clips (T) into the
groove of both panels (B) & (C).
The back panel clips (T) should be evenly
spaced as shown and positioned to allow
the hanging bracket and corner gussets to
be tted. Once in place, tighten screw.
AB
T
T
T
TT
AB
T
Step 12.
Secure L bracket SML (FF) to bottom left and right of wall unit
using 1 x 15mm screws (L) per bracket, as shown.
L
L
FF
FF
A
B
K
K
K
K
9mm
9mm
Step 13.
Measure and attach
hinge mounting plate
onto xed shelf (C) as
shown, using screws
which are already
positioned within the
hinge plates.
192 192
160 160
Top Top
Front Front
37 37
Removed from lift hinge
Hinge Plates
Step 14.
Measure and attach
lift hinge bracket
with 2 x screws per
bracket. The required
screws are included
inside lift hinge pack.
18mm
50mm
35mm
18mm
50mm
35mm
TOP FIXED SHELF
INSIDE FACE
C
Front
92mm 92mm
Shaker
5 Piece
Frontal
ONLY
Shaker
5 Piece
Frontal
ONLY
MEASUREMENTS
FROM INSIDE OF
UNIT
B
B
C

Page 5
WALL UNIT
600 Microwave Assembly Guide
Step 16.
Measure appropriately and attach the 2
x hanging bracket plates onto the wall
screwing through the provided holes into
your wall.
Step 17.
Hang the unit using the
brackets to hook onto the
plate as shown
A
Step 18.
Secure to the wall using 1 x
appropriate screw through each
L brackets (FF).
Hanging Bracket
Plate
Screws for attaching to walls are not provided as these vary
depending on materials, thickness and construction. Ensure
appropriate xings for wall construction are used.
Step a
Insert hanging
bracket into pre-drilled holes
Step c
Secure with provided
2 x 20mm screws (S) per bracket
Step b
Rotate locking
lever 180 degrees
Detail A Detail A
S
S
Detail A
Step 15. Hanging brackets steps a,b & c to be carried out on both sides as shown
Care to be taken. Hanging procedure is necessary for a safe installation.

Page 6
For Internal Use: FI.WR.INS.056.WKIN00123_WALL720_600MW.Rev5
Step 19.
Using points a, b & c adjust the unit to suit.
Step 20.
Screw into any
side units using
the provided
2 x 30mm screws
(K) to secure the
unit. Place cover
caps (M) on the
head to conceal
it.
Removed from lift hinge
Step 23.
Secure hinges by tightening 2 x screws with hinge dowels attached.
These are already positioned within the hinges.
Step 22.
Insert hinges into holes as shown.
142142
110110
BackBack
Left
Right 3030
FRONTAL
Step 21.
Measure and attach lift hinge bracket to frontal with 2 x screw per
bracket. The required screws are included inside lift hinge pack.
K
Step a.
Rotate the screw clockwise
to move the unit up.
Anti-clockwise for down.
Step b.
Adjust the depth using
centre screw.
Step c.
Screw the red screw until
it touches the plate to
lock in position.
b
c
a
Hanging
Bracket
viewed through
Back Panel
C
a
b

Page 7
WALL UNIT
600 Microwave Assembly Guide
Step 24.
Clip hinges into hinge mounting plates on the unit.
Step 25.
Clip lift hinge
mechanisms into
each bracket.
Step 26.
Use a 4mm allen key to adjust the strength of the lift
hinge for the door weight.
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1 - In - Out
Point 2- Left - Right
1
2
FRONTAL HINGE
ADJUSTMENT
View from Inside of unit
To release door,
pull catch as shown,
to release hinge from
the hinge plate. Hinge Cover Caps
Step 27.
Fit cover caps to hinge. Adjust Softclose to suit.
The left and right hinges MUST be adjusted to the
SAME STRENGTH.
The top and bottom hinges
MUST be adjusted to the
SAME STRENGTH.