Wren Kitchens BASE UNIT 1000 User manual

BASE UNIT
1000 2 Door
Assembly Guide
For Internal Use: FI.WR.INS.022_WKIN00104_BASE_1000_2Door_Rev3.indd

BASE UNIT
1000 2 Door
Assembly Guide
For Internal Use:FI.WR.INS.022_WKIN00104_BASE_1000_2Door_Rev3.indd
Page 1
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
L Bracket
x2
Hinge Mounting Plate
x4 Inc Screws
Hinge
x4 Inc Screws
Space Plug
x2
Panel B
x2 End Panel
Panel E
x2 Rail
Panel C
x1 Base Panel
Shelf
x1
Legs
x5
Frontal
(Packed separately)
x2
Panel A
x1 Back Panel (Folded)
Panel D
x1 Muntin
(F) x12
Wooden Dowel
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x8
30mm
Screw
(J) x4
45mm
Screw Black
(L) x32
15mm
Screw
(N) x2
Door
Buer
(Z) x5
Shelf Peg
Plastic
(M) x4
Cover
Cap

BASE UNIT
1000 2 Door
Assembly Guide
For Internal Use: FI.WR.INS.022_WKIN00104_BASE_1000_2Door_Rev3.indd
Page 2
Step 1.
Seat dowel (F) into holes in
both end panels (B) as shown.
Step 2.
Seat cam dowel (G) into holes in
both end panels (B) as shown.
Step 3.
Attach panels (C) &(E) to
panels (B), using cam dowel
(G) & cam lock (H) (in blue),
and also using dowels (F) (in
orange) in positions as shown.
Step 4.
Join panels (C)&(E) to (B).
Insert cam lock (H).
Do NOT tighten until Step 6.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening.
Do NOT use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
GG
G
GF
F
FF
GG FF FF
B
B
G
GF
F
F F
Seat (G)
cam dowel
into hole as
shown.
B
B
C
E
E
B
B
View from underside View from underside
H
G
GH

BASE UNIT
1000 2 Door
Assembly Guide
For Internal Use:FI.WR.INS.022_WKIN00104_BASE_1000_2Door_Rev3.indd
Page 3
Step 7.
Secure back panel (A) with 4 x 30mm
screws (K) equally spaced at the
bottom of back panel (A) into base
panel (C), as shown.
Ensure you screw into the centre of the
base panels (C) (9mm from the edge).
Step 5.
Slide back panel (A) into
groove of end panels (B).
Once back panel (A) is in position, ensure
the panel is ush & square with bottom of
end panels (B).
Step 6.
Hand tighten all cam locks (H), this will
expand cam dowels (G) and tighten the
unit together.
Step 8.
Join muntin panel (D) to unit, use pilot
holes to align muntin. Join muntin panel
(D), base panel (C) & rail panel (E) using
4 x 45mm screws (J) as shown.
B
C
B
E
A
A
K
B
C
B
E
D
9mm
J
J
J
J

BASE UNIT
1000 2 Door
Assembly Guide
For Internal Use: FI.WR.INS.022_WKIN00104_BASE_1000_2Door_Rev3.indd
Page 4
Step 10.
Lightly hit centre peg of leg
base with hammer until ush.
Step 11.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning carcass
upright. Once in situ level accordingly.
Step 9.
Secure each of the legs into
place with 2 x 15mm screws
(L) per leg.
Ensure legs are rotated as shown so that part
of it is supporting the end panels (B).
Front legs should have at edge to the front.
Leg position diagram
C
B
B
Front
Front
C
C
B
B
C
B
Front
L
L
B

BASE UNIT
1000 2 Door
Assembly Guide
For Internal Use:FI.WR.INS.022_WKIN00104_BASE_1000_2Door_Rev3.indd
Page 5
Securing to Adjacent Units
Screw into any side units using the 30mm screws
(K) provided to secure to unit. Screw just to the rear
of the hinge plate at the top and bottom of both
sides of the unit, place a cover cap (M) on the head
to conceal it.
L Brackets
Use 2 x 15mm screws (L) to secure each
of the L brackets to the cabinets at either side.
Then screw up through into the worktop as shown.
Screws for attaching to worktop are not supplied as
these vary depending on worktop material and thickness.
Ensure appropriate xings for attaching worktop are
used. L brackets should only be tted for securing wood
and laminate worktops, please refer to the specialist
worktop supplier if these are required for solid surface
worktops.
Worktop
Screw up through the front rail
into your worktop to secure it in place.
Screws for attaching to worktop are not supplied as these vary
depending on worktop material and thickness. Ensure appropriate
xings for attaching worktop are used. Please refer to the specialist
worktop supplier if these are required for solid surface worktops.
Secure unit to wall using space plugs
Drill 2 pilot holes through the back brace into the wall and insert wall plugs.
Then unwind space plug until it contacts both surfaces. Finally, tighten the screws.
Screws for attaching to walls are not provided as these vary
depending on your wall material and construction. Ensure appropriate xings
for wall construction are used.
LL
K
Step 12.
Attach Hinge Mounting Plate
onto both End Panel or panels,(B) as shown, using Screws
which are already positioned within the Hinge Plates.
Hinge side or sides to be mounted in accordance to
customer kitchen plan.
126mm
126mm
94mm
94mm
B
from base
from top
Hinge Plates

BASE UNIT
1000 2 Door
Assembly Guide
For Internal Use: FI.WR.INS.022_WKIN00104_BASE_1000_2Door_Rev3.indd
Page 6
Step 13.
Insert hinge in top & bottom
holes as shown.
Step 14.
Secure hinges by
tightening
2 x screws with hinge
dowels attached. These
are already positioned
within the hinges.
Step 15.
Attach the door to unit
where required. Adjust
hinges to suit. See below.
To attach door
clip hinge onto hinge
plate and click to secure.
Hinge Cover Caps
Step 17.
Fit cover caps to hinge.
Adjust Softclose to suit.
Step 16.
Adjust hinge to suit. As shown below.
Hinge Plates
View from Inside of Carcass
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1- In - Out
Point 2- Left - Right
12
FRONTAL HINGE
ADJUSTMENT
To Release door
Pull catch as shown,
to release hinge
from the hinge
plate.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.