Wren Kitchens Vogue BASE UNIT 600 2 Drawers Dummy User manual

BASE UNIT
Hob 2 Drw, 3 Drw & 2 Drw inc Dummy Assembly Guide
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_HOB_Drw_Rev5
1000
3 Drawers
800
2 Drawers
600
2 Drawers
800 2 Drawer inc
Dummy Drawer
1000 2 Drawer inc
Dummy Drawer
600 2 Drawer inc
Dummy Drawer

Page 1
BASE UNIT
Hob 2 Drw, 3 Drw & 2 Drw inc Dummy Assembly Guide
Standard Drawer (Packed Separately)
Fitting Pack Contents
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
DRAWER
COVER CAP
x2
DRAWER
COVER CAP
x2
DRAWER SIDE
x1 Right Hand
DRAWER SIDE
x1 Right Hand
DRAWER SIDE
x1 Left Hand
DRAWER SIDE
x1 Left Hand
DRAWER
FRONT
FIXING
x 2
DRAWER
FRONT
FIXING
x 2
Deep Drawer (Packed Separately)
Fitting Pack Contents
(Y) x2
Gallery
Head
(J) x16
Drawer Runner
16mm Screws
(J) x16
Drawer Runner
16mm Screws
(N) x1
Door Buer
(N) x1
Door Buer
(Q) x4
21mm
Screw
(Q) x4
21mm
Screw
(L) x2
15mm
Screw
METAL BACK
PANEL
x 1
METAL BACK
PANEL
x 1
DRAWER
BASE
x 1
DRAWER
BASE
x 1
DRAWER
RUNNER
x 1 Right Hand
DRAWER
RUNNER
x 1 Right Hand
FRONTAL
(Supplied separately)
FRONTAL
(Supplied separately)
DRAWER
RUNNER
x 1 Left Hand
DRAWER
RUNNER
x 1 Left Hand
GALLERY
RAIL
x 2
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
BASE UNIT
Hob 2 Drw, 3 Drw & 2 Drw inc Dummy Assembly Guide
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_HOB_Drw_Rev5
99mm
67mm
99mm
67mm
Step 2.
Clip on metal back panel to drawer base &
drawer sides.
Step 3.
Screw back panel in position using 2 x 16mm screws (J)
to drawer base in holes provided.
Step 1.
Secure drawer base to drawer side using 4 x 16mm
drawer runner screws (J) in holes provided.
Seat the edge of drawer base tight
into corner of casing, as shown.
The decorative face of drawer base
to be positioned as shown.
Metal back
panel
View from back
Metal
back
panel
Drawer base
white
decorative
face up
J
J
J
J
J
J
J
J
J
Front of drawer
Decorative
face
Drawer
base
J
Step 4.
Frontal Attachment
Secure drawer side xing clips using 2 x 21mm
screws (Q) in pilot holes provided as shown.
Drawer
base
Fixing
clip
& (Q)
Fixing
clip
& (Q)
Standard
drawer
Step 6.
Fit drawer cover caps
over drawer side adjustment.
Drawer
Cover Cap
Drawer
frontal
Drawer side
J
Fixing
clip
Drawer side
xing clip
Q
Q
Drawer
frontal
Repeat step 1 so both drawer
sides are attached to drawer base.
View of drawer side
1
3
2b
2a
Step 5.
Draw Adjustment
Screw point 1as shown
to adjust drawer
frontal right & left.
Screw point 2a as
shown to adjust
drawer frontal
up & down.
Tighten 2b
once in position.
Releasing xing clip. Screw
point 3whilst applying
downward pressure as
shown to release.

Page 3
BASE UNIT
Hob 2 Drw, 3 Drw & 2 Drw inc Dummy Assembly Guide
Fixing
clip
& (Q)
Fixing
clip
& (Q)
2
1
Y & L Y & L
Step 6.
Fit gallery rail into the top
corners of metal back panel.
Locate front end of the
gallery rail into the opening
of the gallery head, which
is secured to the frontal as
shown
Deep
drawer
J
JMetal
back
panel
Drawer base
white decorative
face up
Fixing clip
(Y) Gallery
Head
Drawer side
xing clip
Q
Q
Drawer
frontal
Drawer
side
Drawer
frontal
Step 7.
Fit drawer cover caps
over drawer side adjustment.
Drawer
Cover Cap
Step 2.
Clip on metal back panel to drawer base &
drawer sides.
Step 3.
Screw back panel in position using 2 x 16mm screws (J)
to drawer base in holes provided.
Step 1.
Secure drawer base to drawer side using 4 x 16mm
drawer runner screws (J) in holes provided.
Seat the edge of drawer base tight
into corner of casing, as shown.
The decorative face of drawer base
to be positioned as shown.
View from back
Metal
back
panel
Front of drawer
Decorative
face
Drawer
base
J
J
JJ
JJ
Drawer
base
J
Repeat step 1 so both drawer
sides are attached to drawer base.
JJ
Step 5.
Draw Adjustment
Screw point 1as shown to
adjust drawer frontal
right & left.
Drawer Frontal
Adjustment
Screw point 2a
as shown to adjust
drawer frontal up & down.
Tighten 2b
once in position.
Releasing
xing clip.
Screw point 3
whilst applying
downward pressure
as shown to release. View of drawer side
13
2b
2a
Step 4.
Secure drawer side xing clips using 2 x 21mm screws (Q)
& gallery head (Y) using 1 x 15mm screws (L) in pilot holes
provided as shown.

Page 4
BASE UNIT
Hob 2 Drw, 3 Drw & 2 Drw inc Dummy Assembly Guide
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_HOB_Drw_Rev5
(F) x8
Wooden Dowel
(G) x6
Cam Dowel
(Expanding)
(H) x6
Cam Lock
(K) x4
30mm
Screw
(L) x12
15mm
Screw
(M) x4
Cover
Cap
Panel B
x2 End Panel
Panel E
x1 Rail
Panel C
x1 Base Panel
Metal
Rail
x1
Legs
Qty as per order
Frontal
(Packed separately)
Qty as per order
Panel A
x1 Back Panel
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 5
BASE UNIT
Hob 2 Drw, 3 Drw & 2 Drw inc Dummy Assembly Guide
74mm
636mm
360mm
431mm
74mm
From Front
From Front
From Bottom
J
J
3 Drawer
- 2 Drawer
- 2 Drawer
inc Dummy
Drawer
from base
Step 1.
To attach drawer runner screw into end panels (B) using 2 x 16mm screws (J)
per drawer rail, into pilot holes provided, as shown.
Step 2.
Where applicable, secure dummy xing clip
parts (A) onto both End Panels (B) using 2
x15mm screws (L) each, as shown. The top
screw hole is to be positioned 52mm from the
top of the panel (marked by an indentation). Part A
Dummy Fixing Clip
Part B
Drawer runner bracket screw position
J J
37mm 261mm
Panel B
Panel B
L
Panel B
Panel B
E
Part A
52mm
Part A
Dummy Drawer
ONLY
From Top
2 Drawer
inc Dummy Drawer
3 Drawer
2 Drawer

Page 6
BASE UNIT
Hob 2 Drw, 3 Drw & 2 Drw inc Dummy Assembly Guide
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_HOB_Drw_Rev5
Step 3.
Seat dowel (F) into holes in
both end panels (B) as shown. Step 4.
Seat cam dowel (G) into holes in
both end panels (B) as shown.
Step 6.
Insert cam lock (H).
Do NOT tighten until Step 8.
All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening. Do NOT use power tools with
cam dowel (G) or cam lock (H)
Seat (G)
cam dowel
into hole as
shown.
B
B
E
C
B
B
View from underside View from underside
H
G
G
H
Metal Rail
Step 5.
Attach panels (C) & (E) to panels (B), using dowels (F)
(orange) and cam dowel (G) (blue) in positions shown.
Insert metal rail as shown & secure with 2 x 15mm
screws (L) into panels (B).
GG
G
GG
FF
FF
F
F
BB
Metal Rail
Insert
Metal Rail
Insert
Dowel (F), Cam Dowel (G)
& Metal Rail Screw
Location detail

Page 7
BASE UNIT
Hob 2 Drw, 3 Drw & 2 Drw inc Dummy Assembly Guide
9mm
Step 7.
Slide back panel (A) into groove of end panels (B).
The back panel (A) is to be modied accordingly
to suit Customer Requirements, prior to inserting
into unit.
Once back panel (A) is in position, ensure the
panel is ush & square with bottom of
end panels (B).
Step 8.
Hand tighten all cam locks (H), this will
expand cam dowels (G) and tighten the
unit together.
Step 9.
Ensure unit is square. Secure back panel (A) with
3 or 4 x 30mm screws (K) equally spaced at the
bottom of back panel (A) into base panel (C), as
shown.
Ensure you screw into the centre of the base
panels (C) (9mm from the edge).
B
E
C
A
K
K
K
B
CA
600 unit used for reference only

Page 8
BASE UNIT
Hob 2 Drw, 3 Drw & 2 Drw inc Dummy Assembly Guide
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_HOB_Drw_Rev5
It is important to lift the unit onto
its legs. Do not tilt as depicted in
the image.
Step 10.
Position legs as shown.
Ensure legs are rotated to also provide
support to the end panels (B).
600-800 width unit, 4 legs
1000 width units, 5 legs.
Step 11.
Secure each of the legs into place with 4 x 15mm screws (L)
per leg.
L
L
L
L
B
C
B
Step 12.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning unit upright. Once in situ
level accordingly.
C

Page 9
BASE UNIT
Hob 2 Drw, 3 Drw & 2 Drw inc Dummy Assembly Guide
Screw into any side units using the 30mm screws (K)
provided to secure to the unit. Screw just to the rear of
the indentations at the top and bottom on both sides of
the unit where applicable. Place cover caps (M) on the
heads of the screws to conceal them.
K
Screws for attaching to walls and worktop are not provided as these vary depending
on materials, thickness and construction. Ensure appropriate xings for wall and
worktop construction are used. Please refer to the specialist worktop supplier if
these are required for solid surface worktops.
Screw up through the metal rail into
worktop to secure it in place.
Secure unit to wall by screwing through the back rail
and into the wall.