Wren Kitchens WALL UNIT 672 L Corner User manual

WALL UNIT
672 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr_Rev4.indd

WALL UNIT
672 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr_Rev4.indd
Page 1
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Panel A
x1 Back Panel
Panel S
x1 Back Panel
Hanging Bracket
X3 Inc Screws
(F) x16
Wooden
Dowel
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
(G) x8
Cam Dowel
(Expanding)
(W) x8
Cam Dowel
(H) x16
Cam Lock
(K) x4
30mm
Screw
(L) x8
15mm
Screw
(P) x8
45mm
Screw
(S) x6
20mm
Screw
(M) x4
Cover Cap
(N) x2
Door
Buer
(Z) x12
Shelf Peg
Plastic
(T) x10
Back Panel
Support Clip
Hanging Bracket
Plate X3 (Screws Not
Included)
Hinge Mounting Plate
X4 Inc Screws
Hinge
X4 Inc Screws
Corner
Gusset
X2
Hanging
Bracket
Cover Cap
X3
Panel B
x2 End Panel
Panel C
x2 Fixed Shelf
(Top & Bottom)
Panel D
x2 Fixed Shelf
Loose Shelf
x2 Large
Loose Shelf
x2 Small
Corner Post
x1
(packed
separately)
Frontal
(packed
separately)
x2
(U) Fixing
Plate
X2

WALL UNIT
672 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr_Rev4.indd
Page 2
Corner Post
x1
(packed
separately)
Step 1.
Seat dowel
(F) into holes in
end panel (B) as
shown.
Step 2.
Seat cam dowel
(G) into holes in
end panel (B) as
shown.
Step 3.
Attach panels x2 (C) to panel
(B), using cam dowels (G)
& cam locks (H) (in blue),
and also using dowels (F)
(in orange) in positions as
shown.
Step 4.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the
cam dowels (G) and tighten
the unit together.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
C
C
Seat (G)
cam dowel
into hole as
shown.
Dowel (F)
& Cam Dowel (G)
location detail
G
G
F
F
F
F
G
G
B
View from underside
B
CC
H
H
G
G
View from underside

WALL UNIT
672 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr_Rev4.indd
Page 3
Step 5.
Seat dowel (F)
into holes in
both panels (B)
as shown.
Step 6.
Seat expanding
cam dowel (G) into
holes in
both end panels (B)
as shown.
Step 7.
Attach panel (B) to panels
(D) using cam dowels (G)
& cam lock (H) (in blue)
and also using dowels (F)
(in orange) in positions as
shown.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening. Do not use power tools with
cam dowel (G) or cam lock (H)
B
D
D
Dowel (F)
& Cam Dowel (G)
location detail
Seat (G)
cam dowel
into hole as
shown.
Step 8.
Insert cam lock (H).
Hand tighten all cam locks (H), this
will expand the cam dowels (G) and
tighten the unit together.
View from underside
B
CC
H
H
G
G
View from underside
G
G
F
F
F
F
G
G
B

WALL UNIT
672 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr_Rev4.indd
Page 4
Step 9.
Seat dowel (F) into holes
in both panels (D) as
shown.
Step 10.
Seat cam dowel (W)
into holes in panel (D)
as shown.
Step 12.
Insert and hand tighten
all cam locks (H).
Step 11.
Attach panels x 2 (D)
to panels (C) using cam
dowels (W) & cam lock (H)
(in blue) and also using
dowels (F) (in orange) in
positions as shown.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
B
C
D
D
C
C
C
D
C
H
HBB
D
D
Seat (W)
cam dowel
into hole as
shown.
W
W
FF

WALL UNIT
672 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr_Rev4.indd
Page 5
Step 13.
Slide back panel (S) into
groove of panels (C).
Step 14.
Slide back panel (A) into
groove of side panel (B) while
also allowing panel (S) slide
into the groove of panel (A).
Step 16.
Slide 9 x back panel clips
(T) into the groove of both
panels (A), (B) & (C).The
back panel clips (T) should
be evenly spaced as shown
and positioned to allow the
hanging bracket and corner
gussets to be tted. Once
in place, tighten screw.
Step 15.
Ensure all panels are
square. Screw back
panel (A) to panels (C)
& (D) with 8 x screws
(P) using provided pilot
holes.
B
B
C
C
A
S
S
T
A
T
A
P
S
A
C
D

WALL UNIT
672 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr_Rev4.indd
Page 6
Step 17.
Hanging Brackets steps a,b & c to be carried out on both
sides as shown.
Step a
Insert Hanging
Bracket into pre-drilled holes
Step c
Secure with provided
2 x 20mm screws (S) per bracket
Step b
Rotate locking
lever 180 degrees
S
S
Detail A Detail A Detail A
Step 18.
Secure Corner Gussets
to the bottom left and
right hand side of the
wall unit using
4 x 15mm screws (L)
per plate.
L
L
L
L
Detail B
A
B
Pilot
hole
M
Detail B
Step 19.
Drill a small pilot hole through the centre of the Corner Gussets.
Use this hole at the end of the process to screw through and
into the wall. Cover the screw heads using the cover caps (M)
provided.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction. Ensure
appropriate xings for wall constructions are used.
View through
back paanel
A
A
Care to be taken. Hanging procedure
is neccesary for a safe installation.

WALL UNIT
672 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr_Rev4.indd
Page 7
Step 22.
Using points a, b & c adjust the
Cabinet to suit.
Hanging
Bracket
viewed though
Back Panel
C
a
b
Step a.
Rotate the screw clockwise
to move the cabinet up.
Anti-clockwise for down.
Step b.
Adjust the depth
using centre
screw.
Step c.
Screw the red screw until it
touches the plate to lock
in position.
b
c
a
Step 23.
Screw into any side units using the provided 2x
30mm screws (K) to secure the unit. Screw just to the
rear of the hinge plate then place a cover cap on the
head to conceal it.
K
Step 20.
Measure appropriately and attach the 3 x hanging bracket plates onto the
wall screwing through the provided holes into your wall.
Screws for xing to walls are not provided as these vary depending
on your wall material and construction. Ensure appropriate xings for
wall construction are used.
Step 21.
Hang the cabinet using the brackets to hook onto
the plate as shown
Hanging Bracket
Plate

WALL UNIT
672 L Corner
Assembly Guide
For Internal Use: FI.WR.INS.038_WKIN00128_WALL720_672_LCnr_Rev4.indd
Page 8
Step 24.
Align corner post to frontal. Equally space
2 x xing plates (U) to the back of frontal
& corner post.
Ensure a 3mm gap is maintained
between frontal & post
once xed together.
Screw in place using
4 x 15mm screws (L)
per xing plate (U).
U
U
Step 25.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 26.
Attach the door to unit
where required.
To attach door
clip hinge onto hinge
plate and click to secure.
Hinge Cover Caps
Step 27.
Adjust hinge to suit. As shown below.
Hinge Plates
View from Inside of Carcass
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1 - In - Out
Point 2- Left - Right
12
FRONTAL HINGE
ADJUSTMENT
To Release door
Pull catch as shown,
to release hinge
from the hinge
plate.
L
L
L
L
L
L
L
L
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
Step 28
Fit cover caps to hinge.
Adjust Softclose to suit.

WALL UNIT
672 L Corner
Assembly Guide