Wren Kitchens Vogue BASE UNIT 150 1 Door User manual

BASE UNIT
150 - 200 1 Door Assembly Guide
For Internal Use: FI.WR.INS.019_WKIN00100_BASE_150-200_1Dr_Rev7.Indd
150
200

Page 1
BASE UNIT
150 - 200 1 Door Assembly Guide
(F) x12
Wooden
Dowel
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x7
30mm
Screw
(L) x28
15mm
Screw
(N) x1
Door Buer
(Z) x4
Shelf Peg Plastic
(M) x4
Cover Cap
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Panel B
x2 End Panel Panel C
x2 Fixed Panel
Shelf
x1
Legs
x4
Frontal
(Packed separately)
x1
Panel A
x1 Back Panel
REQUIRED TOOLS
NOT to be
used with CAM
DOWEL & CAM
LOCK
L Bracket
x2
Hinge Mounting Plate
x2 Inc Screws
Hinge
x2 Inc Screws

Page 2
For Internal Use: FI.WR.INS.019_WKIN00100_BASE_150-200_1Dr_Rev7.Indd
Step 1.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
Step 2.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
Step 3.
Attach panels (C) to panels (B),
using cam dowel (G) (in blue), and
also using dowels (F) (in orange)
in positions as shown.
Step 4.
Insert cam lock (H).
Do NOT tighten until Step 6.
Do not use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
G GF F
B
B B
B
C
C
B
B
View from underside View from underside
H
G
G
H
Seat (G)
Cam Dowel
into hole as
shown.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
G GF
F
G F F G G F F F

Page 3
BASE UNIT
150 - 200 1 Door Assembly Guide
Step 5.
Slide back panel (A) into groove of
end panels (B).
Once back panel (A) is in position,
ensure the panel is ush & square
with bottom of end panels (B).
Step 6.
Hand tighten all cam locks (H), this
will expand cam dowels (G) and
tighten the unit together.
Step 7.
Ensure unit is square. Secure back
panel (A) with 2 x 30mm screws (K)
at the top & bottom of back panel
(A) into both xed panels (C), as
shown.
Ensure you screw into the centres
of the base panels (C) (9mm from
the edge).
B
C
A
A
C
K
K
B
B9mm
9mm

Page 4
For Internal Use: FI.WR.INS.019_WKIN00100_BASE_150-200_1Dr_Rev7.Indd
Front
Front
C
Leg position diagram
B
B
Step 9.
Secure each of the legs into place with
4 x 15mm screws (L) per leg.
Step 8.
Position legs as shown. Ensure legs are rotated to also
provide support to the end panels (B).
L
L
L
L
B
B
Step 10.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning unit
upright. Once in situ level accordingly.
C
C

Page 5
BASE UNIT
150 - 200 1 Door Assembly Guide
L Brackets
Use 2 x 15mm screws (L) to secure each
of the L brackets to the unit at either
side. Then screw through into the wall as
shown.
Worktop
Screw up through panel (C) into your worktop to secure it in place.
Securing to Adjacent Units
Screw into any side units using the 30mm screws (K) provided to secure
to unit. Screw just to the rear of the hinge plate at the top and bottom of
both sides of the unit, place a cover cap (M) on the head to conceal it.
L
L
K
Step 11.
Attach hinge mounting plate onto both End Panel or panels,
(B) as shown, using Screws which are already positioned within
the Hinge Plates.
Hinge side or sides to be mounted in accordance to
Customer Specic Kitchen Plan.
Hinge Plates 126mm
126mm
94mm
94mm
B
From Bottom
From Top
Screws for attaching to walls and worktop are not provided as these vary depending on materials,
thickness and construction. Ensure appropriate xings for wall and worktop construction are used.
Please refer to the specialist worktop supplier if these are required for solid surface worktops.

Page 6
For Internal Use: FI.WR.INS.019_WKIN00100_BASE_150-200_1Dr_Rev7.Indd
Step 12.
Insert hinge in top & bottom
holes as shown below.
Step 13.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 14.
Attach the door to unit
where required.
To attach door, clip hinge
onto hinge plate and click
to secure.
Hinge Cover Caps
Step 16.
Fit cover caps to hinge.
Adjust Soft close to suit.
Step 15.
Adjust hinge to suit. As shown below.
To adjust hinge using
a screw driver, tighten
or loosen as required
at points 1 & 2.
Point 1- In - Out
Point 2- Left - Right
12
FRONTAL
HINGE
ADJUSTMENT
Hinge Plates
View from inside of Unit
To release door,
pull catch as shown,
to release hinge from
the hinge plate.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
To Move the
hinge up/down,
loosen screws
A + B,
Manoeuvre
the door, then
re-tighten the
screws
A
B