Wren Kitchens BASE UNIT 600 User manual

WALL UNIT
600 Adjustable Corner Assembly Guide
For Internal Use: FI.WR.INS.037_WKIN00127_WALL_600_AdjCnr_Rev6.indd

Page 1
WALL UNIT
600 Adjustable Corner Assembly Guide
Panel A
x1 Back Panel
REQUIRED TOOLS
NOT to be
used with
CAM DOWEL
& CAM LOCK
Panel B
x2 End Panel
Panel C
x2 Base Panel
Frontal
(packed separately)
x1
Blanking Panel
x1
Loose Shelf
x2
Hanging Bracket
x2 Inc Screws
Hanging Bracket Plate
x2
(Screws Not Included)
Hinge Mounting Plate
x2 Inc Screws
Hinge
x2 Inc Screws
Corner Gusset
x2
Hanging Bracket
Cover cap
x2
(F) x8
Wooden
Dowel
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x4
30mm
Screw
(L) x21
15mm
Screw
(S) x4
20mm
Screw
(M) x2
Cover Cap
(FF) x2
L Bracket
SML
(N) x1
Door
Buer
(Z) x8
Shelf Peg
Plastic
(T) x10
Back Panel
Support Clip
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.037_WKIN00127_WALL_600_AdjCnr_Rev6.indd
Step 1.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
Step 2.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
Seat (G)
Cam Dowel
into hole as
shown.
Step 3.
Attach panels x2 (C) to
panel (B), using cam
dowels (G) (in blue), and
also using dowels (F)
(in orange) in positions as
shown.
Step 4.
Slide panel (A) into the
groove of panels (B)
and x 2 (C).
Step 5.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the
cam dowels (G) and tighten
the unit together.
NB. All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
G
G
F
F
F
F
G
G
B
B
A
C
C
View from underside
B
CC
H
H
G
G
View from underside

Page 3
WALL UNIT
600 Adjustable Corner Assembly Guide
Dowel (F)
& Cam Dowel (G)
location detail
G
G
F
F
F
F
G
G
B
Step 6.
Seat dowel (F)
into holes in both
panels (B) as shown.
Step 7.
Seat cam dowel
(G) into holes in
both end panels (B)
as shown.
Step 8.
Attach panel (B) to panels
(C) using cam dowels (G)
(in blue) and also using
dowels (F) (in orange)
in positions as shown.
Ensure panel (A) is seated
into the groove of panel
(B).
Step 9.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the cam
dowels (G) and tighten the
unit together.
NB. All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
B
A
C
C
View from underside
B
CC
H
H
G
G
View from underside
Seat (G)
Cam Dowel
into hole as
shown.

Page 4
For Internal Use: FI.WR.INS.037_WKIN00127_WALL_600_AdjCnr_Rev6.indd
Step 11.
Slide the back panel clips (T) into the groove of both panels (B) &
(C)s. The back panel clips (T) should be evenly spaced as shown and
positioned to allow the hanging bracket and corner gussets to be
tted.Onceinplace,tightenscrew.
Step 10.
Ensure unit is square.
BA
C
A
T
126mm
126mm
94mm
94mm
from top
from base
Step 12.
Attach hinge mounting plates onto end panels (B) in locations
shown using screws already in the mounting plate.
Hinge side or sides to be mounted in accordance to Customer
Specic Kitchen Plan.
A
T
B

Page 5
WALL UNIT
600 Adjustable Corner Assembly Guide
B
AStep 14.
Secure corner gussets
to the bottom left and
right hand side of the
wall unit using
4 x 15mm screws (L) per
plate.
Step a
Insert hanging
bracket into pre-drilled holes
Step c
Secure with provided
2 x 20mm screws (S) per bracket
Step b
Rotate locking
lever 180 degrees
Detail A Detail A
S
S
Detail A
View through
Back Panel
Pilot
hole
M
Detail B
Step 13. Hanging Brackets steps a,b & c to be carried out on both sides as shown
Care to be taken. Hanging procedure is necessary for a safe installation.
L
L
L
L
Detail B
Step 15.
Drill a small pilot hole through the centre of the corner gussets,
through the back of the unit. Use this hole at the end of the
process to screw through and into the wall. Cover the screw
heads using the cover caps (M) provided.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction. Ensure
appropriate xings for wall constructions are used.

Page 6
For Internal Use: FI.WR.INS.037_WKIN00127_WALL_600_AdjCnr_Rev6.indd
WALL UNITS ONLY
Step 16.
Measure appropriately and
attach the 2 x hanging bracket
plates onto the wall screwing
through the provided holes into
your wall.
Step 17.
Hang the unit using the
brackets to hook onto the
plate as shown
Hanging Bracket
Plate
Step 18.
Using points a, b & c adjust the unit to suit.
Step a.
Rotate the screw clockwise
to move the unit up.
Anti-clockwise for down.
Step b.
Adjust the depth
using centre screw.
Step c.
Screw the red screw until it
touches the plate to lock in
position.
Hanging
Bracket
viewed through
Back Panel
b
C
c
a
a
b
KStep 19.
Screw into any side units using the provided 2 x 30mm screws (K) to secure the
unit. Screw just to the rear of the hinge plate then place a cover caps (M) on the
head to conceal it.
Screws for attaching to walls are not provided as these vary depending on materials,
thicknessandconstruction.Ensureappropriatexingsforwallconstructionareused.

Page 7
WALL UNIT
600 Adjustable Corner Assembly Guide
X
Y
Adjustable Corner Post Pack
Panel X
x1
Panel Y
x1
Step 19.
Attach panel (X) to panel (Y)usingappropriatexing.
Adapt panels (X) & (Y) where applicable to suit
Customer Specic Kitchen Plan.
Step 20.
Attach panels (X) & (Y)
to the unit using the
2 x L brackets SML (FF)
and the 4 x 15mm screws
(L) at the top and bottom.
Step 21.
Measure and cut down blanking panel to
required size. Attach to unit using 7 x 15mm
screws (L), evenly spaced as shown.
Ensure you screw through the blanking panel
9mminfromedgesintotheendpanelandxed
shelves to secure in place.
View from
inside
View from
inside
Y
X
FF
FF
L
L
XY
9mm
L
L
L
L
L
L
L

Page 8
For Internal Use: FI.WR.INS.037_WKIN00127_WALL_600_AdjCnr_Rev6.indd
Step 22.
Insert hinge in top & bottom
holes as shown below.
Step 23.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 24.
Attach the door to unit
where required. Adjust
hinges to suit. See below.
To attach door, clip hinge
onto hinge plate and click
to secure.
Hinge Cover Caps
Step 26.
Fit cover caps to hinge.
Adjust Soft close to suit.
Step 25.
Adjust hinge to suit. As shown below.
Hinge Plates
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
To adjust hinge using
a screw driver, tighten
or loosen as required at
points 1& 2.
Point 1-In-Out
Point 2- Left - Right
12
FRONTAL
HINGE
ADJUSTMENT
View from inside of unit
To release door,
pull catch as shown,
to release hinge from
the hinge plate.
To Move the
hinge up/down,
loosen screws
A + B,
Manoeuvre
the door, then
re-tighten the
screws
A
B

Page 9
WALL UNIT
600 Adjustable Corner Assembly Guide

Page 10
For Internal Use: FI.WR.INS.037_WKIN00127_WALL_600_AdjCnr_Rev6.indd