Wren Kitchens Vogue WALL UNIT 1000 Lift User manual

WALL UNIT
1000 Lift Assembly Guide
For Internal Use: FI.WR.INS.033_WKIN00122_WALL_1000_Lift_Extractor_Housing_Rev8.indd
288 x 1000
360 x 1000

Page 1
WALL UNIT
1000 Lift Assembly Guide
Panel A
x1 Back Panel
HANGING
BRACKET
x2 Inc Screws
(F) x8
Wooden
Dowel
REQUIRED TOOLS
NOT to be
used with
CAM DOWEL
& CAM LOCK
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x4
30mm
Screw
(L) x8
15mm
Screw
(S) x4
20mm
Screw
(M) x8
Cover Cap
(N) x1
Door
Buer
(T) x10
Back Panel
Support Clip
HANGING BRACKET
PLATE
x2 (Screws NOT
included)
HINGE MOUNTNG PLATE
x2 Inc Screws
HINGE
x2 Inc Screws
CORNER
GUSSET
x2
HANGING
BRACKET COVER
CAP
x2
LIFT HINGE
x2 Inc Screws
Panel B
x2 End Panel
Panel C
x2 Base Panel
Frontal
(packed separately)
x1
Muntin
x1
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.033_WKIN00122_WALL_1000_Lift_Extractor_Housing_Rev8.indd
Step 2.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
Step 3.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
Seat (G)
cam dowel
into hole as
shown.
Dowel (F)
& Cam Dowel (G)
location detail
G
G
F
F
F
F
G
G
B
Step 3.
Attach panels x2 (C) to panel
(B), using cam dowels (G)
(in blue) and also using
dowels (F) (in orange) in
positions as shown.
Step 4.
Slide panel (A) into the groove
of panels (B) and x 2 (C).
Step 5.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the cam
dowels (G) and tighten the
unit together.
All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
A
C
C
B
C
C
H
H
G
G
View from undersideView from underside

Page 3
WALL UNIT
1000 Lift Assembly Guide
Step 6.
Seat dowel (F) into holes in
both panels (B) as shown.
Step 7.
Seat cam dowel
(G) into holes in
both end panels (B)
as shown.
Step 8.
Attach panel (B) to panels
(C) using cam dowels (G)
(in blue) and also using
dowels (F) (in orange) in
positions as shown. Ensure
panel (A) is seated into the
groove of panel (B).
Step 9.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the
cam dowels (G) and tighten
the unit together.
All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
B
AC
H
H
C
B
C
C
H
H
G
G
View from undersideView from underside
Dowel (F)
& Cam Dowel (G)
location detail
G
G
F
F
F
F
G
G
B
Seat (G)
Cam Dowel
into hole as
shown.

Page 4
For Internal Use: FI.WR.INS.033_WKIN00122_WALL_1000_Lift_Extractor_Housing_Rev8.indd
Step 12.
Slide the back panel clips (T) into
the groove of both panels (B) &
(C). The back panel clips (T) should
be evenly spaced as shown and
positioned to allow the hanging
bracket and corner gussets to
be tted. Once in place, tighten
screw.
The side back panel Clips should
be disregarded for the 288 units.
Step 10.
Join muntin panel (D) to both panels (C) using
4 x 45mm screws (P), through pilot holes provided.
Step 11.
Ensure unit is square.
P
P
A
TAT
C
C
D
B
A
C

Page 5
WALL UNIT
1000 Lift Assembly Guide
Step a
Insert hanging
bracket into pre-drilled holes
Step c
Secure with provided
2 x 20mm screws (S) per bracket
Step b
Rotate locking
lever 180 degrees
Detail A Detail A
S
S
Detail A
Step 13. Hanging Brackets steps a,b & c to be carried out on both sides as shown
A
B
Step 14.
Secure corner gussets to the bottom left and right hand
side of the wall unit using 4 x 15mm screws (L) per plate.
LL
LL
Detail B
View though
Back Panel
Pilot
hole
M
Detail B
Step 15.
Drill a small pilot hole through the centre of the corner
gussets. Use this hole at the end of the process to screw
through and into the wall. Cover the screw heads using the
cover caps (M) provided.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction. Ensure
appropriate xings for wall constructions are used.

Page 6
For Internal Use: FI.WR.INS.033_WKIN00122_WALL_1000_Lift_Extractor_Housing_Rev8.indd
C
16. Hinge Plate.
Using a 5mm Drill bit, drill into Top xed shelf (C) using measurements as shown. Attach Hinge
Mounting Plate onto top xed shelf (C) using screws which are already positioned within the
Hinge Plates.
N.B. for Shaker 5 Piece Frontals, use 35mm measurement (M.
Hinge Plate
B
B
18mm
50mm
35mm
18mm
50mm
35mm
TOP FIXED SHELF
INSIDE FACE
C
Front
92mm 92mm
Shaker
5 Piece
Frontal
ONLY
Shaker
5 Piece
Frontal
ONLY
MEASUREMENTS
FROM INSIDE OF
UNIT

Page 7
WALL UNIT
1000 Lift Assembly Guide
192mm
160mm
Top Top
Front Front
37mm
LEFT HAND RIGHT HAND
B B Removed from lift hinge
142mm 142mm
110mm 110mm
Back
Back
Left
Right 30mm 30mm
FRONTAL
Step 20.
Secure hinges by tightening 2 x screws with hinge dowels
attached. These are already positioned within the hinges.
Step 19.
Insert hinges into holes provided.
Step 17.
Measure and attach lift hinge bracket with 2 x screws per bracket. The required screws are
included inside lift hinge pack.
Step 18.
Measure and attach lift hinge bracket to the frontal with 2 x screws per bracket. The required
screws are included inside lift hinge pack.
192mm
160mm
37mm

Page 8
For Internal Use: FI.WR.INS.033_WKIN00122_WALL_1000_Lift_Extractor_Housing_Rev8.indd
Care to be taken. Hanging procedure is necessary for a safe installation.
Step 21.
Measure appropriately and
attach the 2 x hanging bracket
plates onto the wall screwing
through the provided holes into
your wall.
Step 22.
Hang the unit using the
brackets to hook onto the
plate as shown
Hanging Bracket
Plate
Step 23.
Using points a, b & c adjust the unit to suit.
Step a.
Rotate the screw clockwise
to move the unit up.
Anti-clockwise for down.
Step b.
Adjust the depth using
centre screw.
Step c.
Screw the red screw until it
touches the plate to lock
in position.
Hanging
Bracket
viewed through
Back Panel
b
C
c
a
a
b
KStep 24 .
Screw into any side units using the provided 2x 30mm screws (K) to secure the
unit. Screw just to the rear of the hinge plate then place a cover caps (M) on the
head to conceal it.
Screws for attaching to walls are not provided as these vary depending on materials,
thickness and construction. Ensure appropriate xings for wall construction are used.

Page 9
WALL UNIT
1000 Lift Assembly Guide
Step 25.
Clip hinges into hinge mounting plates on
the unit.
Step 26.
Clip lift hinge mechanisms into each
bracket.
Step 27.
Use a 4mm allen key to adjust
the strength of the lift hinge for
the frontal weight.
Hinge Cover Caps
Step 28.
Fit cover caps to hinge. Adjust Softclose to suit.
The left and right hinges MUST be adjusted to the
SAME STRENGTH.
The top and bottom hinges
MUST be adjusted to the
SAME STRENGTH.
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1- In - Out
Point 2- Left - Right
1
2
FRONTAL HINGE
ADJUSTMENT
View from Inside of unit
To release door,
pull catch as shown,
to release hinge from
the hinge plate.