Wren Kitchens BASE UNIT 600 User manual

300 600
300
TALL
500
TALL
600
TALL
500
For Internal Use: FI.WR.INS.040_WKIN00140_Tower_300-600_2Dr6Shelf_Rev5.indd
TOWER UNIT
300-600 2 Door 6 Shelf
Assembly Guide

LGE L Bracket
x2
Hinge Mounting Plate
x4 Inc Screws
Hinge
x4 Inc Screws
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
(F) x16
Wooden Dowel
(L) x24
15mm
Screw
(G) x12
Cam Dowel
(Expanding)
(H) x12
Cam lock
(M) x4
Cover Cap
(K) x10
30mm
Screw
(N) x2
Door Buer
(Z) x24
Shelf Peg
Plastic
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
Panel A
x1 Back Panel
Panel B
x2 End Panel
Panel C
x2 Base Panel
Panel E
x2 Rail
Shelf
x6
Legs
x5
Frontal (packed separately)
x2
600 tower shown for
illustration purpose.
(U) x2
Fixing Plate
For Internal Use: FI.WR.INS.040_WKIN00140_Tower_300-600_2Dr6Shelf_Rev5.indd
Page 1
TOWER UNIT
300-600 2 Door 6 Shelf
Assembly Guide

B
B
C
C
View from underside View from underside
H
G
G
H
Step 1.
Seat dowel (F) into holes in
both end panels (B) as shown.
Step 2.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
DOWEL (F)
& CAM DOWEL (G)
LOCATION DETAIL
Step 3.
Attach panels (C) & (E) to panels (B),
using cam dowel (G) & cam lock (H) (in blue),
and also using Dowels (F) (in orange) in positions as shown.
NB. All CAM LOCK (H) are to be positioned facing
the outside of the unit carcass, for ease of tightening.
Step 4.
Join panels (C) & (E) to (B).
Insert cam lock (H).
Do NOT tighten until Step 6.
Seat (G)
cam dowel
into hole
as shown
Do not use power tools with
cam dowel (G) or cam lock (H)
B
E
E
C
B
C
GFF G
G F F G
B
GFFG
GFFG
B
G
F
F
G
F
F
G
F
F
G
F
F
For Internal Use: FI.WR.INS.040_WKIN00140_Tower_300-600_2Dr6Shelf_Rev5.indd
Page 2
TOWER UNIT
300-600 2 Door 6 Shelf
Assembly Guide

Step 5.
Slide back panel (A) into groove of end panels (B).
Once back panel (A) is in position,
ensure the panel is ush & square
with bottom of end panels (B).
Step 6.
Hand tighten all cam locks (H),
this will expand cam dowels (G)
and tighten the unit together.
9mm
9mm
B
B
E
E
KA
A
C
C
K
Step 7.
Ensure carcass is square. Secure back
panel (A) with 6 x 30mm screws (K)
equally spaced at the top & bottom of
back panels (A) into base panels (C),
as shown.
Ensure you screw into the centre of base
panel (C) (9mm from the top or bottom
edge where applicale).
For Internal Use: FI.WR.INS.040_WKIN00140_Tower_300-600_2Dr6Shelf_Rev5.indd
Page 3
TOWER UNIT
300-600 2 Door 6 Shelf
Assembly Guide

Step 8.
Secure each of the legs into place with 2
x 15mm screws (L) per leg
Step 10.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning carcass
upright. Once in situ level accordingly.
Step 9.
Lightly tap centre peg of leg base with hammer
until ush.
Ensure legs are rotated as shown so that part
of it is supporting the end panels (B).
Front legs should have at edge to the front.
C
C
C
L
L
C
B
B
B
B
B
Front
Front
C
Leg position diagram
B
For Internal Use: FI.WR.INS.040_WKIN00140_Tower_300-600_2Dr6Shelf_Rev5.indd
Page 4
TOWER UNIT
300-600 2 Door 6 Shelf
Assembly Guide

2070
Step 11.
Attach hinge plates onto end panels (B) In
locations shown using 8 x 15mm screws (L)
Hinge side to be mounted in accordance
to customer kitchen plan.
Secure tower to the wall using L brackets.
Use 2 x 15mm screws (L) to secure each of the
L brackets to the cabinets at either side. Then
screw through into the wall as shown.
Screws for xing to walls are not provided as
these vary depending on your wall material and
construction. Ensure appropriate xings for
wall constructions are used.
Secure tower to the
wall using screws through
rail panel (E) into the wall as shown.
Screws for xing to walls are not provided as these vary depending on
your wall material and construction. Ensure appropriate xings for wall
constructions are used.
See Customer Specic Kitchen Plan
For Tower Frontals
Screw into any side units
using the 30mm
screws (K) provided to
secure to unit.
Screw just to the rear
of the Hinge Mounting
Plate, at the top and
bottom of both sides of
the unit, place a cover
cap on the head to
conceal it.
E
E
2006mm
846mm
626mm
126mm
1974mm
814mm
594mm
94mm L
From Base
1826mm
846mm
626mm
126mm
1794mm
814mm
594mm
94mm
LL
L
LL
L
L
From Base
TALL 2250
2070
B
B
L
L
K
For Internal Use: FI.WR.INS.040_WKIN00140_Tower_300-600_2Dr6Shelf_Rev5.indd
Page 5
TOWER UNIT
300-600 2 Door 6 Shelf
Assembly Guide

Hinge cover caps
U
U
See Customer Specic Kitchen Plan
For Tower Frontals
Fixing plates
Step 14.
Align doors to join together using 2 x xing plates (U) to the back
of both frontals ensure a 3mm gap is maintained between each
frontal once xed together.
Screw in place using 4 x 15mm screws per xing plate.
Step 12.
Insert hinge where required
in holes as shown.
Step 13
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 16.
Fit cover caps to hinge.
Adjust Softclose to suit.
Step 15.
Adjust hinge to suit. As shown below.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
View from Inside of Carcass
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1- In - Out
Point 2- side - side
12
FRONTAL HINGE
ADJUSTMENT
To Release door
Pull catch as shown,
to release hinge
from the hinge
plate.
For Internal Use: FI.WR.INS.040_WKIN00140_Tower_300-600_2Dr6Shelf_Rev5.indd
Page 6
TOWER UNIT
300-600 2 Door 6 Shelf
Assembly Guide