Wren Kitchens BASE UNIT 600 User manual

BASE UNIT
600 - 1000 Hob
2/3 Drawer
Assembly Guide
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_2-3Drw_Hob_Rev1.indd
1000
3 Drawers
800
2 Drawers
600
2 Drawers

BASE UNIT
600 - 1000 Hob
2/3 Drawer
Carcass Assembly
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_2-3Drw_Hob_Rev1.inddPage 1
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Standard Drawer (Packed Separately)
Fitting Pack Contents
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
DRAWER
COVER
CAP
x2
DRAWER
COVER
CAP
x2
METAL BACK PANEL
x 1
DRAWER SIDE
x1 Right Hand
DRAWER SIDE
x1 Right Hand
DRAWER SIDE
x1 Left Hand
DRAWER SIDE
x1 Left Hand
DRAWER
FRONT
FIXING
x 2
DRAWER
FRONT
FIXING
x 2
Deep Drawer (Packed Separately)
Fitting Pack Contents
(Y) x2
Gallery
Head
(J) x16
Drawer Runner
16mm Screws
(J) x16
Drawer Runner
16mm Screws
(N) x1
Door Buer
(N) x1
Door Buer
(Q) x4
21mm
Screw
(Q) x4
21mm
Screw
(L) x2
15mm
Screw
METAL BACK PANEL
x 1
DRAWER
BASE
x 1
DRAWER
BASE
x 1
DRAWER RUNNER
x 1 Right Hand
DRAWER RUNNER
x 1 Right Hand
FRONTAL
(Supplied separately)
FRONTAL
(Supplied separately)
DRAWER RUNNER
x 1 Left Hand
DRAWER RUNNER
x 1 Left Hand
GALLERY
RAIL
x 2
Fixing
clip
& (Q)

BASE UNIT
600 - 1000 Hob
2/3 Drawer
Standard Drawer
Assembly
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_2-3Drw_Hob_Rev1.indd Page 2
Step 2.
Clip on metal back
panel to drawer base
& drawer sides.
Step 3.
Screw back panel in position
using 2 x 16mm screws 
to drawer base in holes
provided.
Step 1.
Secure drawer base to drawer side using 4 x 16mm
drawer runner screws (J) in holes provided.
Seat the edge of drawer base tight
into corner of casing, as shown.
The decorative face of drawer base
to be positioned as shown.
View from
back
Front of drawer
View on side of drawer side
Decorative
face
Drawer
base
1
3
2b
2a
Metal back
panel
Metal back
panel
Drawer base
white decorative
face up
J
J
J
J
J
J
J
J
J
J
Step 4.
Frontal Attachment
Secure drawer side xing clips
using 2 x 21mm screws (Q) in
pilot holes provided as shown.
Step 5.
Draw Adjustment
Screw point 1as shown
to adjust drawer
frontal right & left.
Drawer
base
Fixing
clip
& (Q)
Fixing
clip
& (Q)
Standard
drawer
Step 6.
Fit Drawer Cover Caps
over drawer side adjustment.
Screw point 2a as
shown to adjust
drawer frontal
up & down.
Tighten 2b
once in position.
Releasing  Screw
point 3whilst applying
downward pressure as
shown to release.
Drawer
Cover Cap
Fixing
clip
Drawer Frontal Adjustment
Drawer
frontal
Drawer
side
Drawer side
xing clip
Q
Q
J
Drawer
frontal
Repeat step 1 so both drawer
sides are attached to drawer base.
99mm
67mm
99mm
67mm

BASE UNIT
600 - 1000 Hob
2/3 Drawer
Deep Drawer
Assembly
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_2-3Drw_Hob_Rev1.inddPage 3
Step 1.
Secure drawer base to drawer side using
4 x 16mm drawer runner screws (J) in
holes provided.
Seat the edge of drawerbase tight
into corner ofcasing, as shown.
The decorative face of drawer base
to be positioned as shown.
J
J
J
J
J
J
Drawer
base
Fixing
clip
& (Q)
Fixing
clip
& (Q)
Drawer
side
Drawer side
xing clip
Q
Q
2
1
J
JStep 2.
Clip on metal back
panel to drawer base
& drawer sides.
Y & L Y & L
Step 5.
Draw Adjustment
Screw point 1as shown to
adjust drawer frontal
right & left.
Step 6.
Fit Gallery Rail into the
top corners of Metal
BackPanel.
Locate front end of the
Gallery Rail into the
opening of the gallery
Head, which is secured to
the frontal as shown
Step 7.
Fit Drawer Cover Caps
over drawer side adjustment.
Drawer Cover Cap
Drawer Frontal
Adjustment
Screw point 2a
as shown to adjust
drawer frontal up & down.
Tighten 2b
once in position.
Releasing 
Screw point 3
whilst applying downward pressure as
shown to release. View on side of drawer side
Deep
drawer
Front of drawer
Decorative
face
Drawer
base
J
JMetal back
panel
Drawer base
white decorative
face up
Step 3.
Screw back panel in position using
2 x 16mm screws to drawer base in holes provided.
Step 4.
Frontal Attachment
Secure 
using 2 x 21mm screws (Q) in pilot holes provided as
shown.
Fixing clip
Gallery Head
Repeat step 1 so both drawer
sides are attached to drawer base.
Drawer
frontal
Drawer
frontal
View from
back
Metal
back
panel
J
231mm
99mm
67mm
231mm
99mm
67mm

BASE UNIT
600 - 1000 Hob
2/3 Drawer
Carcass Assembly
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_2-3Drw_Hob_Rev1.indd Page 4
Fixing
clip
& (Q)
Y & L
(F) x8
Wooden Dowel
(G) x6
Cam Dowel
(Expanding)

Cam Lock
(K) x4
30mm
Screw
(L) x12
15mm
Screw
(M) x4
Cover
Cap
Panel B
x2 End Panel
Panel E
x1 Rail
Panel C
x1 Base Panel
Shelf
x1
Sink
Rail
x1
Legs
x4 or 5
as req’d
Frontal
(Packed separately)
x1 or 2 as Req’d
Panel A
x1 Back Panel
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
sink rail +
screws



BEFORE YOU START
INSTALLATION

PERFORMED BY A
COMPETENT
PERSON ONLY.

BE DANGEROUS
IF INCORRECTLY
INSTALLED

BASE UNIT
600 - 1000 Hob
2/3 Drawer
Assembly Guide
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_2-3Drw_Hob_Rev1.indd
Page 5
2 drawer
3 drawer
Step 1.
To attach drawer runner
screw into end panels (B)
using 2 x 16mm screws (J)
per drawer rail, into
pilot holes provided,
3rd hole from front,
as shown.
In the case of a 140 Dummy
drawer, utilise secondary
drilling (blue)to secure
xing clips.
B
B
37mm 261mm
74mm
646mm
360mm
431mm
74mm
from front
from front
from base
Drawer runner bracket screw position
JJ
J
J
from base
636mm

BASE UNIT
600 - 1000 Hob
2/3 Drawer
Assembly Guide
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_2-3Drw_Hob_Rev1.indd
Page 6
Step 2.
Seat dowel (F) into holes in
both end panels (B) as shown.
Step 3.
Seat cam dowel (G) into holes in
both end panels (B) as shown.
Step 5.
Join panels (C) to (B).
Insert cam lock .
Do NOT tighten until Step 6.
All    are to be positioned facing the
outside of the unit carcass, for ease of tightening. Do NOT use power tools with
cam dowel (G) or cam lock 
Seat (G)
cam dowel
into hole as
shown.
B
B
C
B
B
View from underside View from underside

G
G

Sink Rail
Step 4.
Attach panels (C) & (E) to panels (B), using dowels (F)
(orange) and cam dowel (G) & cam lock  (blue) in
positions shown.
Insert sink rails as shown & secure with 2 x 15mm
screws (L) into panels (B).
GG
G
GG
FF
FF
F
F
BB
Sink Rail
Insert
Sink Rail
Insert
Dowel (F), Cam Dowel (G)
& Sink Rail Screw
Location detail

BASE UNIT
600 - 1000 Hob
2/3 Drawer
Assembly Guide
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_2-3Drw_Hob_Rev1.indd
Page 7
9mm
Step 6.
Slide back panel (A) into
groove of end panels (B).
The back Panel (A) is to be modied accordingly
to suit Customer Requirements,prior to inserting
into cabinet. for 1000 width cabinets,
the Back panel.
Once back panel (A) is in position, ensure the
panel is ush & square with bottom of
end panels (B).
Step 7.
Hand tighten all cam locks , this will
expand cam dowels (G) and tighten the
unit together.
Step 8.
Ensure carcass is square. Secure back panel (A)
with 3 or 4 x 30mm screws (K) equally spaced at
the bottom of back panel (A) into base panel (C),
as shown.
Ensure you screw into the centre of the base
panels (C) (9mm from the edge).
B
E
C
A
K
B
CA
600 Carcase used for example

BASE UNIT
600 - 1000 Hob
2/3 Drawer
Assembly Guide
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_2-3Drw_Hob_Rev1.indd
Page 8
Step 9.
Secure each of the legs into place
with 2 x 15mm screws (L).
600-800 Width Cabinets, 4 legs
1000 with Cabinets, 5 legs
Step 11.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning carcass
upright. Once in situ level accordingly.
Ensure legs are rotated as shown so that part
of it is supporting the end panels (B).
Front legs should have at edge to the front.
Leg position diagram
1000 Carcase used for example
C
C
B
L
L
B
B
B
Front
Front
Front
C
C
B
BStep 10.
Lightly hit centre peg of leg
base with hammer until ush.

BASE UNIT
600 - 1000 Hob
2/3 Drawer
Assembly Guide
For Internal Use: FI.WR.INS.058_WKIN00112_BASE_600-1000_2-3Drw_Hob_Rev1.indd
Page 9
Securing to adjacent units
Screw into any side units using the
30mm screws (K) provided to secure to
the unit. Screw just to the rear at the
top and bottom of both sides of the
unit, place a cover cap (M) on the head
to conceal it.
Worktop
Screw up through the front sink rail (and
additional rail where applicable) into worktop to
secure it in place.
Screws for attaching to worktop are
not supplied as these vary depending
on worktop material and thickness. Ensure

used. Please refer to the specialist worktop
supplier if these are required for solid
surface worktops.
K
Securing to Wall
Secure unit to wall using 2 Screws. Drill 2 pilot holes
through the back rail into the wall and insert wall plugs,
tighten the screws.
Screws for attaching to walls are not provided as these
vary depending on your wall material and construction.

used.