Wren Kitchens BASE UNIT 150 User manual

BASE UNIT
150-200 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.019_WKIN00100_BASE_150-200_1Dr_Rev4.indd
150
200

BASE UNIT
150-200 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.019_WKIN00100_BASE_150-200_1Dr_Rev4.indd
Page 1
(F) x12
Wooden Dowel
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x7
30mm
Screw
(L) x28
15mm
Screw
(N) x1
Door
Buer
(Z) x4
Shelf Peg
Plastic
(M) x4
Cover
Cap
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Panel B
x2 End Panel Panel C
x2 Fixed Panel
Shelf
x1
Legs
x4
Frontal
(Packed separately)
x1
Panel A
x1 Back Panel
REQUIRED TOOLS
NOT to be used with
CAM DOWEL & CAM
LOCK
L Bracket
x2
Hinge Mounting Plate
x2 Inc Screws
Hinge
x2 Inc Screws

BASE UNIT
150 -200 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.019_WKIN00100_BASE_150-200_1Dr_Rev4.indd
Page 2
Step 1.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
Step 2.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
Step 3.
Attach panels (C) to panels
(B), using cam dowel (G)
& cam lock (H) (in blue),
and also using dowels (F)
(in orange) in positions as
shown.
Step 4.
Join panels (C) to (B).
Insert cam lock (H).
Do NOT tighten until Step 6.
Do not use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
G GF F
B
B B
B
C
C
B
B
View from underside View from underside
H
G
G
H
Seat (G)
cam dowel
into hole as
shown.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
G GF
F
G F F G G F F F

BASE UNIT
150-200 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.019_WKIN00100_BASE_150-200_1Dr_Rev4.indd
Page 3
Step 5.
Slide back panel (A) into groove of
end panels (B).
Once back panel (A) is in position,
ensure the panel is ush & square
with bottom of end panels (B).
Step 6.
Hand tighten all cam locks (H), this
will expand cam dowels (G) and
tighten the unit together.
Step 7.
Ensure carcase is square. Secure
back panel (A) with 2 x 30mm
screws (K) at the top & bottom
of back panel (A) into both xed
panels (C), as shown.
Ensure you screw into the centres
of the base panels (C) (9mm from
the edge).
B
C
A
A
C
K
K
B
B9mm
9mm

BASE UNIT
150 -200 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.019_WKIN00100_BASE_150-200_1Dr_Rev4.indd
Page 4
Step 8.
Secure each of the legs into place
with 2 x 15mm screws (L) per leg.
Step 9.
Lightly tap centre peg of leg
base with hammer until ush.
Step 10.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning carcase
upright. Once in situ level accordingly.
Ensure legs are rotated as shown so that part
of it is supporting the end panels (B).
Front legs should have at edge to the front.
C
C
B
B
C
B
Front
Front
Front
C
L L
B
Leg position diagram
B
B

BASE UNIT
150-200 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.019_WKIN00100_BASE_150-200_1Dr_Rev4.indd
Page 5
L Brackets
Use 2 x 15mm screws (L) to secure each
of the L brackets to the cabinets at either
side. Then screw through into the wall
as shown.
Screws for attaching to walls are
not provided as these vary
depending on your wall material and
construction. Ensure appropriate
xings for wall construction are used.
Worktop
Screw up through panel (C) into
your worktop to secure it in place.
Screws for attaching to worktop are
not supplied as these vary depending
on worktop material and thickness. Ensure
appropriate xings for attaching worktop are
used. Please refer to the specialist worktop
supplier if these are required for solid surface
worktops.
Securing to Adjacent Units
Screw into any side units using
the 30mm screws (K) provided to
secure to unit. Screw just to the rear of
the hinge plate at the top and bottom
of both sides of the unit, place a cover
cap (M) on the head to conceal it.
L
L
K
Step 11.
Attach hinge mounting plate onto both End Panel or panels,
(B) as shown, using Screws which are already positioned within
the Hinge Plates.
Hinge side or sides to be mounted in accordance to
customer kitchen plan.
Hinge Plates
126mm
126mm
94mm
94mm
B
from base
from top

BASE UNIT
150 -200 1 Door
Assembly Guide
For Internal Use: FI.WR.INS.019_WKIN00100_BASE_150-200_1Dr_Rev4.indd
Page 6
Step 12.
Insert hinge in top & bottom
holes as shown below.
Step 13.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 14.
Attach the door to unit
where required. Adjust
hinges to suit. See below.
To attach door,
clip hinge onto hinge
plate and click to secure.
Hinge Cover Caps
Step 16.
Fit cover caps to hinge.
Adjust Softclose to suit.
Step 15.
Adjust hinge to suit. As shown below.
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1- In - Out
Point 2- Left - Right
12
FRONTAL
HINGE
ADJUSTMENT
Hinge Plates
View from inside of Carcase
To release door,
pull catch as shown,
to release hinge from
the hinge plate.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.