Wren Kitchens Vogue 600 User manual

TOWER UNIT
600 Double Appliances Inc Dr + Drw Assembly Guide
For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw.Rev7
2070 x 600
600 + 450 Appliance
2250 x 600 Tall
600 + 450 Appliance

Page 1
TOWER UNIT
600 Double Appliances Inc Dr + Drw Assembly Guide
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
DRAWER
COVER
CAP
x2
DRAWER SIDE
x1 Right Hand
DRAWER SIDE
x1 Left Hand
DRAWER
FRONT
FIXING
x 2
Deep Drawer (Packed Separately)
Fitting Pack Contents
(Y) x2
Gallery
Head
(J) x16
Drawer Runner
16mm Screws
(N) x1
Door Buer
(Q) x4
21mm
Screw
(L) x2
15mm
Screw
METAL BACK PANEL
x 1
DRAWER
BASE
x 1
DRAWER RUNNER
x 1 Right Hand
FRONTAL
(Supplied separately)
DRAWER RUNNER
x 1 Left Hand
GALLERY
RAIL
x 2
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw.Rev7
Fixing
clip
& (Q)
Fixing
clip
& (Q)
2
1
Y & L Y & L
Step 6.
Fit Gallery Rail into the top
corners of metal back panel.
Locate front end of the
gallery rail into the opening
of the gallery head, which
is secured to the frontal as
shown
Deep
drawer
J
JMetal
back
panel
Drawer base
white decorative
face up
Fixing clip
(Y) Gallery
Head
Drawer side
xing clip
Q
Q
Drawer
frontal
Drawer side
Drawer
frontal
Step 7.
Fit drawer cover caps
over drawer side adjustment.
Drawer
Cover Cap
Step 3.
Screw back panel in position using 2 x 16mm screws (J)
to drawer base in holes provided.
Step 1.
Secure drawer base to drawer side using 4 x 16mm
drawer runner screws (J) in holes provided.
Seat the edge of drawer base tight
into corner of casing, as shown.
The decorative face of drawer base
to be positioned as shown.
View from back
Metal
back
panel
Front of drawer
Decorative
face
Drawer
base
J
J
JJ
JJ
Drawer
base
J
Repeat step 1 so both drawer
sides are attached to drawer base.
JJ
Step 5.
Draw Adjustment
Screw point 1as shown to
adjust drawer frontal
right & left.
Drawer Frontal
Adjustment
Screw point 2a
as shown to adjust
drawer frontal up & down.
Tighten 2b
once in position.
Releasing
xing clip.
Screw point 3
whilst applying
downward pressure
as shown to release. View of drawer side
13
2b
2a
Step 4.
Frontal Attachment
Secure drawer side xing clips using 2 x 21mm screws (Q)
& gallery head (Y) using 1 x 15mm screws (L) in pilot holes
provided as shown.

Page 3
TOWER UNIT
600 Double Appliances Inc Dr + Drw Assembly Guide
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
(F) x24
Wooden
Dowel
(J) x24
16mm
Screw
(G) x20
Cam Dowel
(Expanding)
(H) x20
Cam lock
(M) x4
Cover Cap
(K) x16
30mm
Screw
(R) x30
19mm
Screw
(N) x2
Door Buer
(U) x2
Fixing Plate
(Z) x12
Shelf Peg
Plastic
L BRACKET LGE
x2
L BRACKET SML
(FF) x4
HINGE MOUNTING PLATE
x2 Inc Screws
HINGE
x2 (Inc Screws)
Panel B
x2 End Panel
Panel A
x2 Back Panel
Panel E
x2 Rail
Appliance Shelf
x1
Legs
x5
Frontal
x1 (Packed separately)
Panel C
x4 Base Panel
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 4
For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw.Rev7
600+450 Appliance
Inc 1 Door + 1 Drawer
N.B. L Bracket SML
For appliance shelf, secure to
panel (B) using 4 x L brackets
SML (FF) locate according
to customer appliance
requirements.
1826mm
1794mm
1826mm
1794mm
1592mm
1560mm
1592mm
1560mm
Fixed Shelf 1468mm Fixed Shelf 1468mm
Fixed Shelf 282mm Fixed Shelf 282mm
BTM BTM
TOP TOP
74mm 74mm
37mm 37mm
261mm 261mm
From Bottom From Bottom
From Front From Front
B
LEFT HAND RIGHT HAND
B
Example
Locations
ONLY
Example
Locations
ONLY
FF FFFF FF
Drawer runner bracket screw position
JJ
Step 1.
To attach drawer runner screw into end panels (B)
using 2 x 16mm screws (J) per drawer runner, into pilot holes provided,
3rd hole from front, as shown.
J
J
B
Step 2.
Attach hinge plates onto end panels (B) to suit as shown using 2 screws
already in hinge plates.
Hinge side or sides to be mounted in accordance to Customer Specic
Kitchen Plan.

Page 5
TOWER UNIT
600 Double Appliances Inc Dr + Drw Assembly Guide
600+450 Appliance
Inc 1 Door + 1 Drawer
Step 2.
Attach hinge plates onto end panels (B) to suit as shown using 2 screws
already in hinge plates.
Hinge side or sides to be mounted in accordance to Customer Specic
Kitchen Plan.
N.B. L Bracket SML
For appliance shelf, secure to
panel (B) using 4 x L brackets
SML (FF) locate according
to customer appliance
requirements.
2006mm
1974mm
2006mm
1974mm
1485mm
1453mm
1485mm
1453mm
Fixed Shelf 1367mm Fixed Shelf 1367mm
Fixed Shelf 282mm Fixed Shelf 282mm
BTM BTM
TOP TOP
74mm 74mm
37mm
37mm
261mm
261mm
from base from base
from front from front
B
LEFT HAND RIGHT HAND
B
Example
Locations
ONLY
Example
Locations
ONLY
FF FF FF FF
Step 1.
To attach drawer runner screw into end panels (B)
using 2 x 16mm screws (J) per drawer runner, into pilot
holes provided, 3rd hole from front, as shown.
J
J
Drawer runner bracket screw position
B
JJ

Page 6
For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw.Rev7
Appliance Shelf example location only
B
B
EE
C
C
CC
Step 5.
Attach Panels (C) & (E) to panels (B), using
cam dowel (G) (in blue), and also using
dowels (F) (in orange) in positions as shown.
Step 6.
Insert cam lock (H).
Do NOT tighten until Step 9.
NB. All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
Step 3.
Seat dowel (F) into holes in
both end panels (B) as shown.
Step 4.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
B
B
C
C
View from underside View from underside
H
G
G
H
Seat (G)
cam dowel
into hole as
shown.

Page 7
TOWER UNIT
600 Double Appliances Inc Dr + Drw Assembly Guide
9mm
9mm
K
A
A
C
K
Step 7.
Cut back panel (A) to suit appliance
option, leaving the centre appliance
aperture open.
B
A A
A
A
C
C
E
E
Step 8.
Slide back panel (A) into
groove of end panels (B).
Once back panel (A) is in position,
ensure the panel is ush & square with
bottom of end panels (B).
Step 10.
Ensure unit is square. Secure
back panel (A) with 12 x 30mm
screws (K) equally spaced
at the top & bottom of back
panels (A) into base panels (C),
as shown.
Ensure you screw into the
centre of base panel (C) (9mm
from the top or bottom edge
where applicable).
Step 9.
Hand tighten all cam
locks (H), this will expand
cam dowels (G) and
tighten the unit together.

Page 8
For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw.Rev7
9mm
B
B
Front
Front
C
Leg position diagram
Step 11.
Position legs as shown.
Ensure legs are rotated to also provide
support to the end panels (B).
Step 12.
Secure each of the legs into place with
4 x 15mm screws (L) per leg.
B
L
L
L
L
C
B
C
Step 13.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning unit upright.
Once in situ level accordingly.
It is important to lift unit
onto its legs. Do not tilt as
depicted in image.

Page 9
TOWER UNIT
600 Double Appliances Inc Dr + Drw Assembly Guide
Secure tower to the wall using L brackets.
Use 2 x 15mm screws (L) to secure each of the L brackets LGE
to the unit at either side.
Then screw through into the wall as shown.
Secure tower to the wall using screws through rail panel (E)
into the wall as shown.
Screw into any side units using the 30mm screws (K)
provided to secure to unit.
Screw just to the rear of the hinge mounting plates, at
the top and bottom of both sides of the unit, place a
cover caps (M) on the heads to conceal it.
L
L
E
E
K
Screws for attaching to walls are not provided as these vary depending on
materials, thickness and construction. Ensure appropriate xings for wall
construction are used.

Page 10
For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw.Rev7
Step 12.
Insert hinge in top & bottom
holes as shown below.
Step 13.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 14.
Attach the door to unit
where required.
To attach door, clip hinge
onto hinge plate and click
to secure.
Hinge Cover Caps
Step 16.
Fit cover caps to hinge.
Adjust Soft close to suit.
Step 15.
Adjust hinge to suit. As shown below.
To adjust hinge using
a screw driver, tighten
or loosen as required
at points 1& 2.
Point 1- In - Out
Point 2- Left - Right
12
FRONTAL
HINGE
ADJUSTMENT
Hinge Plates
View from inside of Unit
To release door,
pull catch as shown,
to release hinge from
the hinge plate.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
To Move the
hinge up/down,
loosen screws
A + B,
Manoeuvre
the door, then
re-tighten the
screws
A
B