Wren Kitchens 2070 User manual
TOWER UNIT
2070 & 2250 Diag Corner Larder with Wine Rack Assembly Guide
For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev9
2250 x 600 Tall2070 x 600
1 Door
50/50 Door
70/30 Door
Page 1
TOWER UNIT
2070 & 2250 Diag Corner Larder with Wine Rack Assembly Guide
(FF) L Bracket
SML
x6
L Bracket LGE
x4
(L) x142
15mm
Screw
(K) x6
30mm
Screw
Door Buer
x4
Metal Shelf Peg
x56
Plinth Attachment
(To order)
Unit (RH)
Right Hand
Unit (LH)
Left Hand
Panel C
x1 Top Panel Frontals
50/50 or 1Dr or 70/30
Frontal Plinth
(To order)
Unit Plinth
(To order)
Hinge Mounting Plate
(To order) Inc Screws
Hinge
(To order) Inc Screws
Fixing Plate (U)
x19
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
70/30
OPTION
50/50
OPTION
1Dr
OPTION
(Packed Separately)
Legs
x10
(M) x8
Cover Cap
(Per Colour)
BEFORE YOU START
INSTALLATION
SHOULD BE PERFORMED
BY A COMPETENT PERSON
ONLY.
THIS PRODUCT COULD
BE DANGEROUS IF
INCORRECTLY INSTALLED
Page 2
For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev9
Step 1.
Lay both units (LH) & (RH) fiat as shown.
Secure 5 x ‹xing plate (U) positioned onto outside
face of panel (B) of unit (RH) equally spaced using
2 x 15mm screws (L) as shown.
Step 2.
Using 2 x 15mm screws (L) per plate secure
2 x ‹xing plate (U) positioned onto
outside face of panel (C) of unit (RH) using
measurements shown.
L
L
L
L
U
View from above
Unit RH
View from above
Unit RH
C
B
U
C
U
C
RH
LH B
RH
Fixing Plate diagram
View from Above
365mm
170mm
OUTSIDE
FACE
C
Front
Page 3
TOWER UNIT
2070 & 2250 Diag Corner Larder with Wine Rack Assembly Guide
Step 3.
Secure leg base into place with
4 x 15mm screws (L) per leg as shown.
Ensure legs are rotated to also provide
support to the end panels (B).
Front legs should have fiat edge to the
front.
Step 5.
Push leg ‹rmly down into leg base.
Adjust legs to 155mm before turning
both units upright. Once in situ level
accordingly.
It is important to lift unit onto its legs. Do not tilt as depicted in image.
BB
Front
RH A
FrontFrontFront
LH A
Leg position diagram
View From Underside
A
B
L
L L
L
Page 4
For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev9
Step 6.
Position unit LH and unit RH together as shown.
Ensure units are fiush & square.
Step 8.
Align 2 x L bracket SML (FF) combined with
2 x 15mm screws (L) per bracket as shown.
Secure from inside the unit as shown.
Step 7.
Screw through ‹xing plate (U)
into adjoining unit LH using
2 x 15mm screws (L) to secure
both units together.
Repeat per ‹xing plate(U).
L
L
U
U
U
U
U
U
U
LH
RH
Front
Front
View from rear of unit
LH
RH
LL
LL
LL
U
U
U
Front
LH
RH
U
U
FF
Page 5
TOWER UNIT
2070 & 2250 Diag Corner Larder with Wine Rack Assembly Guide
Front Front
Step 9.
Use 2 x 15mm screws (L) to secure each of the
4 x L brackets (LGE) to both units positioned as shown.
L
L
Step 10.
Screw through large L bracket (LGE) into the wall as shown.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction.
Ensure appropriate xings for wall constructions are used.
Fixings
to Wall
Page 6
For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev9
Step 11.
When combined unit is secured in
position, attach top Panel (C), using
4 x ‹xing plates (U) combined with
4 x 15mm screws (L) per plate,
positioned as shown.
Step 12.
Measure plinth and cut to suit the width of unit (LH) and again for (RH).
Mark clip positions by aligning plinth sections to legs. Use 2 x 15mm screws (L) as shown to ‹x clip to
plinth. Detach the leg clip from the plinth clip. Slide leg clip into plinth clip as shown.
Top Panel C
U & L
U & LU & L
U & L
Plinth
Plinth
Leg
Brace
L
Step 13.
Secure plinth by pushing clip ‹rmly onto legs as shown.
Plinth
Plinth
LH RH
INSIDE
FACE
L
Page 7
TOWER UNIT
2070 & 2250 Diag Corner Larder with Wine Rack Assembly Guide
70/30
HINGE
POSITION
50/50
From Bottom From Bottom
From Top From Top
50/50 & 1 Door
HINGE
POSITION
1826mm 1826mm
626mm
846mm
1336mm
866mm
1086mm
126mm 126mm
1794mm 1794mm
594mm
814mm
1304mm
834mm
1054mm
94mm 94mm
Front Front
70/30 1 Dr
Door
INSIDE
FACE
INSIDE
FACE
BB
BB
Step 14.
Attach hinge plates onto end panels (B) to suit as shown using 2 screws already positioned
within the hinge plate.
Hinge side or sides to be mounted in accordance to Customer Specic Kitchen Plan.
Page 8
For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev9
70/30
HINGE
POSITION
50/50
HINGE
POSITION
2006mm 2006mm
126mm 126mm
806mm
814mm
1394mm
626mm
1026mm
1516mm
1974mm 1974mm
94mm 94mm
774mm
846mm
1426mm
594mm
994mm
1484mm
From Bottom From Bottom
From Top From Top
Front Front
Step 14.
Attach hinge plates onto end panels (B) to suit as shown using 2 screws already positioned
within the hinge plate.
Hinge side or sides to be mounted in accordance to Customer Specic Kitchen Plan.
70/30
BB
INSIDE
FACE
INSIDE
FACE
BB
50/50
Page 9
TOWER UNIT
2070 & 2250 Diag Corner Larder with Wine Rack Assembly Guide
126mm
94mm
1 Door
HINGE
POSITION
2006mm
1201.5mm
930.5mm
1169.5mm
898.5mm
1974mm
From Bottom
From Top
Front
1 Door
B
BB
INSIDE
FACE
Step 14.
Attach hinge plates onto end panels (B) to suit as shown using 2 screws already positioned
within the hinge plate.
Hinge side or sides to be mounted in accordance to Customer Specic Kitchen Plan.
Page 10
For Internal Use: FI.WR.INS.097_WKIN00199_TOWER45WineRack_Assembly_Rev9
U
U
U
UU
U
1DOOR OPTION50/50 & 70/30
OPTIONS
Step 2.
Align doors & frontal plinth to join together
using ‹xing plates (U) to the back of both
frontals. Ensure a 4mm gap is maintained
between each frontal once ‹xed together.
Screw in place using 4 x 15mm screws (L)
per ‹xing plate (U).
Fixing plate
Step 3.
Secure hinges by tightening 2 x screws with
hinge dowels attached. These are already
positioned within the hinges.
Door Frontal Fixing (Where Applicable)
Innity +
Doors Supplied in accordance to
customer specic kitchen plan
Hinge dowels
Step 4.
Attach the door to unit, clip hinge onto
hinge plate and click to secure.
Step 1.
Insert hinge into hinge holes provided, in
accordance with customers plan.
Hinge cover caps
Step 5.
Adjust hinge to suit. As shown below.
Hinge plates
View from Inside of unit
To adjust hinge using
a screw driver, tighten
or loosen as required at
points 1& 2.
Point 1 - In - Out
Point 2- Left - Right
1
2
FRONTAL
HINGE
ADJUSTMENT
To release door, pull
catch as shown, to
release hinge from
the hinge plate.
Step 6.
Fit cover caps to hinge.
Adjust soft close to suit.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
To move the
hinge up/down,
loosen screws
A + B,
manoeuvre
the door, then
re-tighten the
screws
A
B
Page 11
TOWER UNIT
2070 & 2250 Diag Corner Larder with Wine Rack Assembly Guide
Door Frontal Fixing (Where Applicable)
Innity
Doors supplied in accordance to
customer specic kitchen plan
Step 4.
Adjust hinge to suit. As shown below.
Step 5.
Fit cover caps to hinge.
Adjust soft close to suit.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
View from Inside of Unit
To adjust hinge using
a screw driver, tighten
or loosen as required at
points 1& 2.
Point 1 - In - Out
Point 2- Left - Right
12
FRONTAL
HINGE
ADJUSTMENT
To release door
Pull catch as shown,
to release hinge
from the hinge
plate.
Hinge cover caps
Hinge Plates
To move the
hinge up/down,
loosen screws
A + B,
Manoeuvre
the door, then
re-tighten the
screws
A
B
Hinge dowels
U
U
U
UU
U
50/50 & 70/30
OPTIONS
Step 2.
Align doors & frontal plinth to join together
using ‹xing plates (U) to the back of both
frontals. Ensure a 4mm gap is maintained
between each frontal once ‹xed together.
Screw in place using 4 x 15mm screws (L)
per ‹xing plate (U).
Fixing plate
Step 3.
Secure hinges by tightening 2 x screws with
hinge dowels attached. These are already
positioned within the hinges.
Step 4.
Attach the door to unit, clip hinge onto
hinge plate and click to secure.
Step 1.
Insert hinge into hinge holes provided, in
accordance with customers plan.
1DOOR OPTION
Other manuals for 2070
2
This manual suits for next models
1
Other Wren Kitchens Indoor Furnishing manuals
Wren Kitchens
Wren Kitchens Vogue BASE UNIT 800 2 Door User manual
Wren Kitchens
Wren Kitchens FI.PK.FIT.004 User manual
Wren Kitchens
Wren Kitchens Vogue 150 Tall User manual
Wren Kitchens
Wren Kitchens BASE UNIT 600 User manual
Wren Kitchens
Wren Kitchens Diag Corner Larder User manual
Wren Kitchens
Wren Kitchens BASE UNIT 600 Built Under Oven Housing User manual
Wren Kitchens
Wren Kitchens BASE UNIT 600 User manual
Wren Kitchens
Wren Kitchens Vogue TOWER UNIT Boiler Housing User manual
Wren Kitchens
Wren Kitchens Vogue WALL UNIT 600 Lift User manual
Wren Kitchens
Wren Kitchens Vogue TOWER UNIT 600 2 Door Fridge / Freezer User manual
Wren Kitchens
Wren Kitchens BASE UNIT 600 User manual
Wren Kitchens
Wren Kitchens Vogue WALL UNIT 1000 Tall 2 Door User manual
Wren Kitchens
Wren Kitchens FI.PK.FIT.004 Assembly instructions
Wren Kitchens
Wren Kitchens Vogue TOWER UNIT 2070 User manual
Wren Kitchens
Wren Kitchens Vogue BASE UNIT 600 2 Drawer User manual
Wren Kitchens
Wren Kitchens Vogue BASE UNIT 972 L Corner User manual
Wren Kitchens
Wren Kitchens Vogue WALL UNIT 1000 Lift User manual
Wren Kitchens
Wren Kitchens TOWER UNIT 84 Walk in User manual
Wren Kitchens
Wren Kitchens BASE UNIT 600 User manual
Wren Kitchens
Wren Kitchens FRONTALS INFINITY PLUS User manual
Popular Indoor Furnishing manuals by other brands
Regency
Regency LWMS3015 Assembly instructions
Furniture of America
Furniture of America CM7751C Assembly instructions
Safavieh Furniture
Safavieh Furniture Estella CNS5731 manual
PLACES OF STYLE
PLACES OF STYLE Ovalfuss Assembly instruction
Trasman
Trasman 1138 Bo1 Assembly manual
Costway
Costway JV10856 manual
