Yale Assure Lock Lever Touchscreen YRL226 User manual

• Yale Assure
Lever®
Touchscreen (YRL226J and Key-Free Touchscreen (YRL256J
Installation and Programming Instructions
This manual will walk you through all the required steps to
add your new Yale Assure Lever to yourdoor.
• Remove existing door knob or lever
• Double checkdoor measurements
• Installyour Assure Lever
• Program your Assure Lever
• Add your Assure Lever to your smart home system or
Yale Access app if purchased with Yale Smart Module or
Yale Access Upgrade Kit
Tools Needed
~
Standard
Phillips Head
Screwdriver
Tools Needed For New Doors
Or Adjusting Existing Door
le
r;;v~
~ ~ I!
Drill 0 Wood Level
[b
Utility Pencil Mortise
Tape Knife
Measure Chisel
JJ
DOWNLOAD
THE BILT APP
Billo tJMNI MIN
··---------------------------·
Usingthe app on your smart
phone, scan this OR for step-by-
step installation instructions & to
registeryourlock
l!l
&WARNING
This product can expose you to lead which is known to the state of California to cause cancer and
birth defects or other reproductive harm. For more information go to www.P65warnings.ca.gov.
Failure tofollowthese instructions could result in damage to the product, voidingthe
factory warranty and could lead to failure of the product to provide access.
Trusted everyday ISL-
1929 - 00 - 002 Ver.3
P/N YRL-TS- MNL - 0018 Rev B Part
of ASSA ABLOY
J

What's In The Box
1 2 3
4 5 6
7 B 9
✓ O 0
0
Touchscreen Keypad
~
Yale Smart Module
Key l
(not included with j
(YRL226)
NR models)
COR~
Cylinder
(YRL226)
e
Key-Free
Cylinder
(YRL256)
@
•
Let's Get Started
Installation Guide
and DoorTemplate
Levers
o I I o Battery
Cover
Key
0
Inside Lock
Battery Cover
[OJ
AAAlkaline
Batteries
Mounting Hardware @
~
Strike Plate
~h
x4
Mounting Plate
@
T
x2
#8-32 X 5/16"
Machine Screws
@
x2
(AYRL- DRIVE
Adjustable Drive-In Latch
available for purchase)
#7 wood & #8-32
Machinex 20mm
Combination Screws
M4x22mm
Pan Head Machine
Screws
(

1
~
~
Removing Existing Door Knob
or l ever
_f-) _ Do not discard old lock hardware untilAssure Lever
•'r:f has been successfully installed.
,._~
I
,~ I~
~,fiY
"' IC
-~
'11"
~~, @~

2 Check
Door Measurements and
Make Adjustments If Needed
Door Checker
Use doorcheckerfrom installation guide envelope to verify yourdoor
measurements and make anyneeded adjustments.
Let's GetStarted
New Door MarkingTemplate
Check
Your Door
Guide
With the door checker, usethe template from installation guide envelope to prep
a new doorthat has not been predrilled for hardware
Let's Get Started
New Door
Marking
Template
Outside of Right Hand Door
YRL226 Cylinderand Key Shown
YRL256 has Key-Free Cylinder (No Key)

3
2J==
CJ-o
x2
For Lever
Actual Size
x2
For Strike Plate
Actual Size
Install Latch and Strike Plate
Right Hand Installation Shown
t
'
-ri -
't::f
AYRL-DRIVE
Adjustable Drive-In Latch
available for purchase
ffl 2-3/8
11
through bolt posts, default
0 +
PULL
/
Q2-3/4
11
through bolt posts, optional
Note: Adjustment is based on backset
Outside
of Door
2-3/8
11
(60mm)
or
2-3/4
11
(70mm)
Backset
"" Ill o
~r!ltfl
,,.~F -
~ -
,,
,,

Install Touchscreen
Right Hand Installation Shown
11
TOP
11
mark must be on
top surface and tailpiece
in vertical position.
~ Incorrect orientation will
~ cause lock to fail.
&
Doorface hole
must be at least
2-7/8".
If hole is too
small, a door lock
installation kit or
jigshould be used
to increase hole
size.
Inside of
Right Hand Door
Outside of
Right Hand Door

5
~
c=r-c
x2
Actual Size
Install Mounting Plate
Right Hand Installation Shown
"'
Inside of
Right Hand Door
&
Make sure keypad
and mounting plate
are straight before
tightening screws.
--
-
"'
Inside of
Right Hand Door
Insert cable through cable hole
-- -
(tpl - ~ - - ~~,,
f

2J:=
C}-c::I
Attach Cable
Right Hand Installation Shown
Inside of
Right Hand Door
©
(JJ) (JJ)
(Yi Ridges along edges
facing outwa rd
~~[i,
Use cable
hookfor
proper cable
routing. Do
notpinch
cable.
Ol) Ol)
8
8
Ii\ Make sure
~ cable is secure
•
[t,
~
@

Install Inside Lock
Right Hand Installation Shown
I
x2
Actual Size
Hookbottom of lockinto
place and listen for a
"click".Tilt lock into place
untillock is flush with door.
&
Make sure tailpiece
inserts into lockas tilting into
, position. DO NOT FORCE
..
Inside of
Right Hand
Door
,,
~,,
...
o,:o
@)
@)
"Click" Hook
....
..

8 Install
Cylinder (YRL226)
2J=
C)-o
or Key-F r ee Cylinder (YRL256)
~ -
YRL226 Cylinder
Remove keyfrom cylinder.
Latch
Outside of
Right Hand Door
OR
e
YRL256 Key-Free Cylinder
There is no key.
Cylinder
Tailpiece
(YRL226) must
slide into
&
Cylinder mustbe installed
with barawayfrom latch
Tailpiece
111..... / Bar
~ ----------- ...... ~
.:.::_Cl/_ Bar
Cylinder
or (YRL226)
Key-Free Cylinder
(YRL256)