Yale 630F User manual

630F & 634F Exit Device Trim
Installation Instructions
1. Check box for components.
2. After marking door inside face for device location (Device Instructions),
carry “ Vertical Reference Centerline” from inside door face. Follow
steps 2a. and 2b., shown below.
3. Transfer Horizontal Reference Centerline from inside to outside door face.
4. Align trim template and tape to outside door face.
5. Spot holes and prepare door for trim
6. Mount trim to door thru holes “A” with (2) mounting screws as shown in
Fig. 2. Use the remaining (3) oval headed screws and finish washers to
secure the trim to the door surface thru location “B” as shown in Fig. 2,
the third screw and washer attaches to the hole located at the bottom
of the trim.
7. Continue as shown in device instructions.
Installation Instructions
Figure 2
22
2-3/4
(70)
630F Trim
2-3/4
(70)
634F Trim
(Push-Pull Door
when dogged)
630F Trim 634F Trim
Escutcheon
Assembly
(2) 1/4-20 Pan Head
Machine Screws
Packed with device.
2 STUDS TOWARDS
LOCK EDGE
(3) 1/4-20 Oval Head
2 STUDS AWAY
FROM LOCK EDGE
(2) #14 Finishing
Washers
Escutcheon
Assembly
(2) 1/4-20 Pan Head
Machine Screws
Packed with device.
2 STUDS TOWARDS
LOCK EDGE
(2) 1/4-20 Oval Head
2 STUDS AWAY
FROM LOCK EDGE
Attention Installer
Any retrofit or other field modification to a fire
rated opening can potentially impact the fire
rating of the opening, and Yale Locks &
Hardware makes no representations or
warranties concerning what such impact may be
in any specific situation. When retrofitting any
portion of an existing fire rated opening, or
specifying and installing a new fire-rated
opening, please consult with a code specialist or
local code official (Authority Having Jurisdiction)
to ensure compliance with all applicable codes
and ratings.
80-8470-0634-000 (11-18)
An ASSA ABLOY Group brand
WARNING
This product can expose
you to lead which is
known to the state of
California to cause cancer
and birth defects or other
reproductive harm. For
more information go to
www.P65warnings.ca.gov.
08/2018

CAUTION: Office copiers and facsimile mach-
ines may change the size of a drawing and make
the template inaccurate to use as a door marker.
If this is not the original template packed with the
trim, use only the holes on the door (do not use
template as a door marker).
630F & 634F
Trim Template
630F
634F
“A” & “X”
"
"
"
Product Support Tel [phone] • Fax [phone] • www.yalelocks.com
Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.
Yale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Other products' brand names may be trademarks or registered trademarks of
their respective owners and are mentioned for reference purposes only. These materials are protected under U.S. copyright laws. All contents current at time of publication.
Yale Security Inc. reserves the right to change availability of any item, its design, construction, and/or its materials.
Copyright © 2005, 2013, Yale Security Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
9-1/2
(241.3)
"A"
"X""X"
11/16
(17)
11/16
(17)
See Chart
4 "X" HOLES
"X""X"
C
LHORIZONTAL
REFERENCE
( Device & Trim)
C
L
C
LVERTICAL
REFERENCE
( Trim)
C
L
3-5/8
(92)
3-5/8
(92)
80-8470-0634-000 (11-18)
An ASSA ABLOY Group brand