Yealink MeetingSpace VC200 User manual

Yealink VC200 Video Conferencing Endpoint Quick Start Guide
V43.10 Applies to firmware version 80.43.0.10 or later
Yealink Network Technology CO., LTD
English | 简体中文

TV TV
The base of the camera must be parallel to the top of TV.
You can adjust the angle of the camera manually. The angle can be up to 30 degree.
Choose other installation method if the thickness of the TV is more than 36 mm.
1
Package Contents
3m
Ethernet Cable
AAA Battery×2
VC200 Codec
VCR11
Remote Control
1.8m
HDMI Cable
(for the display device)
Cable Tie×5
Power Cord
2m Ethernet Cable
(CAT5E FTP cable)
PSE
OK
Quick
Start Guide
1/4”-20 UNC
Screw
We recommend that you use the accessories provided or approved by Yealink. The use of
unapproved third-party accessories may result in reduced performance.
Use the Yealink original PoE adapter (54V/0.56A) to charge the endpoint only. The use of the
third-party PoE adapter may cause the damage to the endpoint.
Put the magnet rings on the HDMI cable to prevent electromagnetic interference.
Endpoint Installation
Select one of the following installation method:
Put on a Flat Surface
You can put the endpoint on a conference room table.
Mount on top of a TV
You can mount endpoint on top of the TV when the thickness of the TV is between 1mm and
36mm.
PoE Adapter
Camera Lens
Privacy cover

48mm
2
1
2
Hole depth: 30mm
Hole diameter: 6mm
3
TV Stand
Mount on a Wall
You can purchase a bracket to mount your endpoint on a wall. The recommended height is
1.6m above the ground.
Mount onto a TV Stand or a Tripod
You need to purchase a TV stand or a tripod separately. The TV stand or a tripod should be
able to bear the weight of at least 5kg.
1/4”-20 UNC screw
1/4”-20 UNC screw
T4×30 screws
Expansion bolts

3
PSE
VCH50
MINI DP HDMI
Codec
Audio
Endpoint Connections
Display
1.8m HDMI Cable
3m Ethernet Cable
Choose one of the following:
Wired network: connect the 2m Ethernet cable
Wireless network: do not connect an Ethernet cable
You can choose wired sharing or wireless sharing method to share PC content. You need to
purchase the desired accessories.
Wired Sharing
VC Hub/Phone port
on VC200 codec
7.5m Ethernet Cable
1.2m
HDMI Cable
1.2m
Mini-DP Cable or
PC
Sharing Content
HDMI
PC
0.6m
HDMI Cable
0.6m USB
Type-C Cable or
PC
VCH51
PoE
VC Hub/Phone port
on VC200 codec
7.5m Ethernet Cable
B: For VCH51 video conferencing hub:
A: For VCH50 video conferencing hub:

4
Remote Control and Cable Ties Installation
Network Environment
Bandwidth Requirements
Both downlink bandwidth and uplink bandwidth should meet above requirements.
The bandwidth mentioned above is based on a two-way call. Bandwidth in head office should be
increased along with the growing number of connected branch offices.
Network Deployment
Choose Cloud deployment or traditional deployment according to your need.
Cloud Deployment
Cloud deployment does not need complex network settings. You only need to get account
information from your system administrator, and log into the video conference platform.
Do the following to log into the video conference platform via remote control:
1. Select More->Setting->Advanced (Default Admin Password:0000)->Video Conference Platform.
2. In the Cloud Account field, check the Enabled checkbox.
Video Resolution Recommended Bandwidth
Full HD 1080P 1.3Mb
People 1080P+Content 1080P 2.6Mb
For more information on WPP20 wireless presentation pod, refer
to Yealink WPP20 Wireless Presentation Pod Quick Start Guide.
PC
Wireless Sharing
WPP20
Wireless Presentation Pod

5
3. Select the desired platform from the pull-down list of Platform Type.
4. Configure the desired platform and log in.
Traditional Deployment
If you deploy the endpoint in the head office, make sure it is reachable from public network.
If you deploy the endpoint in the branch office, use intelligent traversal to deploy it or just follow the
same steps as for the head office.
Head Office
If you deploy the endpoint in the head office, at least one static public IP address is required to allow
branch offices to connect.
Do one of the following to deploy the endpoint:
Option1: Assign a static public IP address to your endpoint.
Option2: If you deploy the endpoint in an Intranet (behind the firewall), assign a static private IP
address to it and do port mapping on the firewall.
Configure a Static IP
The following introduces how to use the remote control to configure a static IPv4 address:
1. Select More->Network->Wired Network (Default Admin Password:0000).
2. Select IPv4 from the pull-down list of IP Mode.
3. Select IPv4, and then press OK key.
4. Uncheck the DHCP checkbox.
5. Enter the IP address, subnet mask, gateway and DNS information in corresponding fields.
6. Save the change.
The screen prompts “Reboot now?” .
7. Select OK to reboot the endpoint .
Configure Port Mapping
If you deploy the endpoint in an Intranet, you must forward the following ports to the public network
on the firewall, so that your endpoint can receive a public-to-private call.
Branch Office
If you deploy the endpoint in the branch office, do one of the following to deploy it:
Port
Function
H.323 signal port
SIP（optional ）
Audio & Video media stream port
Web management port（optional ）
Protocol Type
UDP/TCP
5060-5061
443
50000-51000
1719-1720
TCP/UDP
TCP/UDP
TCP

6
Option1: Deploy the endpoint following the same steps as for the head office. In this way,
both inbound and outbound calls are available.
Option2: Deploy the endpoint using intelligent traversal. You only need to assign a private IP
address to your endpoint. Make sure this private IP address can access the public network.
Only outbound calls are available when using this method.
When you use intelligent traversal to deploy your endpoint, you have to open following ports on
your firewall if they are restricted.
It is recommended that you forward the web management port(443/TCP) to the public network, so
that the head office can remotely manage the branch office.
Troubleshooting
Connectivity Testing
After installation and deployment, you can test the endpoint by dialing the Yealink Demo Room
(117.28.251.50 or 117.28.234.45 ). If you can’t dial out successfully, please contact your IT administrator
to check the network.
Configuring Static NAT
If you do not use Cloud platform and deploy your endpoint in an Intranet, you have configured port
mapping on the firewall or gateway, but you find that local endpoint appears black screen and you
cannot hear sound when you call Yealink Demo or other endpoints. The most likely reason is that the
firewall or gateway in your environment does not support the ALG feature. In this situation, please take
the following actions so that the static NAT feature on the endpoint can solve this problem.
To configure static NAT via the remote control:
1. Select More->Network->Wired Network (Default Admin Password:0000)->NAT/Firewall.
2. Select Auto from the pull-down list of Type, the endpoint will obtain public IP address automatically.
3. If the endpoint does not obtain a public IP address automatically, select Manual Settings from the
pull-down list of Type, and then enter the public IP address in the Public IP Address field.
4. Save the change.
PortFunction
H.323 signal port
SIP（optional ）
Audio & Video media stream port
Protocol Type
UDP/TCP
TCP/UDP
TCP/UDP
50000-51000
5060-5061
1719-1720

包装清单
VCR11遥控器 7号电池x2 VC200主机 3米网线
束线带x 5
1.8米HDMI线
（用于接显示设备）
电视 电视
此为A级产品。在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对干扰
采取切实可行的措施。
我们推荐使用由Yealink提供或经Yealink认可的配件和线缆，使用未经认可的第三方配件和线缆可能
会导致性能的下降。
我们要求使用Yealink原装PoE电源（54V/0.56A），使用第三方电源可能会导致终端损坏。如果使用
过程中发现线缆破皮，请立即更换。
使用HDMI线前，请套上磁环用于抗电磁干扰。
尽量保证终端底壳与电视上方水平。
手动调节摄像机上下角度时，最大调整范围为30°角。
电视厚度超过36mm时，请勿使用挂装方式，终端有跌落风险。请选用其他安装方式。
安装终端
你可以根据实际需要选择安装终端的方式：
平放安装
将终端摆放在水平桌面。
挂装
当电视厚度范围为1mm-36mm时，你可以根据图示将终端挂在电视上。
7
OK
VC200
快速入门指南
1/4”-20 UNC
英制螺钉
VC200最佳部署
实践方案
电源线
2米网线
(FTP超五类以太网线)
PSE
PoE电源
镜头隐私盖

48mm
3
8
电视架
螺丝规格：
1/4”-20 UNC英制螺钉
电视架或三脚架安装
你可以将终端安装在自行选购的电视架或三脚架上，选购的电视架或三脚架承重至少为5kg。
墙装
螺丝规格：1/4”-20 UNC英制螺钉
螺丝规格：T4×30
打孔直径： 6mm
打孔深度： 30mm
12
你可以选购支架将终端安装在墙上，安装高度建议1.6m。
膨胀螺栓

9
连接终端
PSE
3米网线
任选一种网络连接方式：
有线网络：使用2米网线连接
无线网络：此网口无需接网线
显示设备
1.8米HDMI线
你可以选购有线辅流配件或者无线辅流配件用于演示。
7.5米网线
1.2米Mini-DP线 1.2米HDMI线
或
终端上的
VC Hub/Phone口
连接有线辅流
连接辅流
A: 对于VCH50有线辅流分享:
VCH50
MINI DP HDMI
Codec
Audio
PC
HDMI
PC
PC
VCH51
PoE
终端上的
VC Hub/Phone口
7.5米网线
0.6米
USB Type-C线 或 0.6米HDMI线
B: 对于VCH51有线辅流分享: