Yealink MeetingSpace VC800 User manual

按供应商要求封面做了出血3mm
Yealink VC800 Full HD Video Conferencing System Quick Start Guide
Applies to firmware version 63.32.0.3 or later
V32.35
Yealink Network Technology CO., LTD

VCH50 Video
Conferencing Hub
3m
Ethernet Cable
AAA Battery×2
A Package
VC800
Quick Start Guide
1.2m
Mini-DP Cable
0.8m
Ethernet Cable
Mounting Bracket
and Accessories
1.2m
HDMI Cable
(for content sharing)
CP960
Conference Phone
Package Contents
VC800 Codec
+
+
+
2
2
2
0.3m
Micro USB Cable
Charger Cradle
B Package
We recommend that you use the accessories provided or approved by Yealink. The use of unapproved third-party accessories may
result in reduced performance.
VC800 system can work with A package or B package.
CPW90
Quick Start Guide
CPW90 Wireless
Expansion Mic×2
VCR11
Remote Control
OK
CP960
Conference Phone
CPE90 Wired
Expansion Mic×2
Cable Tie×5 Power Adapter
Velcro×2
VESA Accessory
Put the magnet rings on the HDMI cable to prevent electromagnetic interference.
(One Velcro is on the bracket)
1
Acrylic board
1.8m
HDMI Cable×2
(for the display device)
+
1
7.5m
Ethernet Cable
System Installation
Select one of the following installation method based on your site requirements:
Put on a Flat Surface
Mount on top of a TV
Mount on a wall
Mount on a ceiling
Mount onto a TV stand or a tripod
.
.
.
.
.

Steps：
1
3
2
4
3
Open the baffle.
Push the bracket along the track of the V800 codec.
Remove one Velcro.
Put the bracket on the top of the TV.
Stick a Velcro onto the back of the TV, and make sure that the bracket and the back of the TV are tightly positioned against each
other.
TV
5
4
5
Pay attention to the direction of the bracket
Mount on top of a TV
Put on a Flat Surface
You can put the system on a conference room table, and make sure that the slope is not more than 15 degrees so that the system
can operate correctly.
Please choose the following installation method when the thickness of the TV is between 50mm and 100 mm.
TV
5
6
4
3
2
1
2
3
1
Pay attention to the direction of the bracket
If your system cannot be mounted on the top of a TV when the bracket has
reached the given location, remove the bracket, and then convert its direction.
Refer to the following section for more information.
2
The system may fall down when the thickness of the TV is more than 100 mm. In this situation, do not mount the system on the
top of a TV.
Please choose the following installation method when the thickness of the TV is between 16mm and 55mm.

Steps：
1
3
2
4
3
Open the baffle.
Push the bracket along the track of the system.
Stick a Velcro onto the bracket.
Remove one Velcro.
Put the bracket on the top of the TV.
Stick a Velcro onto the back of the TV, and make sure that the bracket and the back of the TV are tightly positioned against
each other.
5
6
Do not pick up the bracket which connects
with a system, the system may
fall down in this situation.
48mm
Hole diameter: 6mm
Hole depth: 30mm
Screw specification: T4×30
Mount on a Wall
2
1
The recommended height is 1.55m-1.85m above the ground.
X
If your system cannot be mounted on the top of a TV
when the bracket has reached the given location, you
should choose other installation methods.
3

Steps：
1
2
3
4
Punch holes into the wall and then insert the expansion bolts.
Secure the bracket using the T4×30 screws.
Push the system along the track of the bracket.
Secure the system onto the bracket using the M3×8 screws.
3
4
Screw specification: M3×8
Mount on a Ceiling
.
.
.
14.0mm （0.55in.）62.5mm
(2.46in.)
Screw hole
6.0 mm(0.24 in.) in depth
Location hole
5.0 mm(0.20 in.) in diameter
4
If you choose the ceiling-mounted installation, you need to purchase a bracket separately. The bracket must meet the following
requirements:
Able to bear the weight of at least 10.5kg (23.15 lb.) and the thickness must be between 2mm (0.08 in.) and 3 mm (0.12 in.).
Comes with a location pillar, which can be inserted into the location hole of the VESA accessory.
The distance between the screw on the bracket and the location pillar must be 14 mm (0.55 in.).

5
1 2
Screw specification: M3×8
Remote Control and Cable Ties Installation
3
Screw specification: M3×8
1
2
3
Push the VESA accessory along the track of the system.
Secure the VESA accessory to the system using the M3×8 screws.
Align the location pillar at the location hole, and then secure the bracket to the VESA accessory using the 1/4”-20 UNC screw.
TV Stand
Mount onto a TV Stand or a Tripod
You need to purchase a TV stand or a tripod separately. The TV stand or tripod has the same requirements as the backet used in the
ceiling-mounted installation method.
The installation steps are the same as the ceiling-mounted installation steps.
Steps：
1
2
3
Screw specification:
1/4”-20 UNC
Screw specification:
1/4”-20 UNC

Connections
VCH50
Power Adapter
Display×2
1.8m
HDMI Cable
3m
Ethernet Cable
0.8m
Ethernet Cable
CP960
Power Adapter
Display×2
1.8m
HDMI Cable
7.5m
Ethernet Cable
3m
Ethernet Cable
0.8m
Ethernet Cable
CP960
MINI DP HDMI
Codec
Audio
7.5m
Ethernet Cable
VCH50
MINI DP HDMI
Codec
Audio
6
If you do not need the VCH50 video conferencing hub to share content, you can connect the VC Hub/Phone port on the system to the
Internet port on the CP960 conference phone directly.
When CP960 conference phone works with the system, the 3.5mm Audio-out port and Micro USB port on the CP960 conference
phone are unavailable.
The system should be used with Yealink original power adapter (48V/0.7A) only. The use of the third-party power adapter may
cause the damage to the system. The cable should be replaced at once if its skin is broken.
If system works with A package, do the following:
If system works with B package, do the following:

7
VCH50
MINI DP HDMI
Codec
Audio
Wired Sharing
VC Hub/Phone port
on VC800 codec
7.5m Ethernet Cable
1.2m
HDMI Cable
1.2m
Mini-DP Cable or
Wireless Sharing
PC
Network Environment
Bandwidth Requirements
Both downlink bandwidth and uplink bandwidth should meet above requirements.
The bandwidth mentioned above is based on a two-way call. Bandwidth in head office should be increased along with the growing
number of connected branch offices.
Network Deployment
Choose Cloud deployment or traditional deployment according to your need.
Cloud Deployment
Cloud deployment does not need complex network settings. You only need to get account information from your system administrator, and
log into video conference platform.
Do the following to log into video conference platform via remote control:
1. Select More->Setting->Advanced (Default Admin Password:0000)->Video Conference Platform.
2. In the Cloud Account field, check the Enabled checkbox.
3. Select the desired platform from the pull-down list of Platform Type.
4. Configure the desired platform and log in.
Video Resolution Recommended Bandwidth
Full HD 1080P 1.3Mb
People 1080P+Content 1080P 2.6Mb
WPP20 Wireless Presentation PodWF50 Wi-Fi USB Dongle
PC
For more information on WPP20 wireless presentation pod, refer to Yealink WPP20 Wireless Presentation
Pod Quick Start Guide.

8
Traditional Deployment
If you deploy the system in the head office, make sure it is reachable from public network.
If you deploy the system in the branch office, use intelligent traversal to deploy it or just follow the same steps as for the head office.
Head Office
If you deploy the system in the head office, at least one static public IP address is required to allow branch offices to connect.
Do one of the following to deploy the system:
Option1: Assign a static public IP address to your system.
Option2: If you deploy the system in an Intranet (behind the firewall), assign a static private IP address to it and do port mapping on the firewall.
Configure a Static IP
The following introduces how to use the remote control to configure a static IPv4 address:
1. Select More->Setting->Advanced (Default Admin Password:0000)->Wired Network.
2. Select IPv4 from the pull-down list of IP Mode.
3. Select IPv4, and then press OK key.
4. Uncheck the DHCP checkbox.
5. Enter the IP address, subnet mask, gateway and DNS information in corresponding fields.
6. Save the change.
The display device prompts “Reboot now?”
.
7. Select OK to reboot the system.
Configure Port Mapping
If you deploye system in an Intranet, you must forward the following ports to the public network on the firewall, so that your system can
receive a public-to-private call.
Branch Office
If you deploy system in the branch office, do one of the following to deploy it:
Option1: Deploy the system following the same steps as for the head office. In this way, both inbound and outbound calls are available.
Option2: Deploy the system using intelligent traversal. You only need to assign a private IP address to your system. Make sure this
private IP address can access the public network. Only outbound calls are available when using this method.
When you use intelligent traversal to deploy your system, you have to open following ports on your firewall if they are restricted.
It is recommended that you forward the web management port(443/TCP) to the public network, so that the head office can remotely
manage the branch office.
PortFunction
H.323 signal port
SIP（optional ）
Audio & Video media stream port
Web management port（optional ）
Protocol Type
UDP/TCP
5060-5061
443
50000-51000
1719-1720
TCP/UDP
TCP/UDP
TCP
PortFunction
H.323 signal port
SIP（optional ）
Audio & Video media stream port
Protocol Type
UDP/TCP
TCP/UDP
TCP/UDP
50000-51000
5060-5061
1719-1720