Yealink VC110 User manual

尺寸：175*130MM
页数：16P
材质：200G铜版纸
印刷要求：双面彩色印刷+封面复亚膜+骑马钉
Yealink VC110 Video Conferencing Endpoint Quick Start Guide
Applies to firmware version 50.21.0.20 or later
V21.20
Yealink Network Technology CO., LTD

Table of Contents
Packaging Contents 01
VC110-All-in-one Unit Connection Diagram 02
Remote Control and Cable Ties Installation 04
VC110-All-in-one Unit Installation 05
Cable Hub Connection Diagram 07
Main Screen 08
Network Deployment 09
Troubleshooting 13

Packaging Contents
1
Quick Start Guide
DVI Cable VGA Cable
(2m)
Ethernet Cable
HDMI Cable Power Adapter Cable Ties 5
+
VCM30
Microphone Array Package
Wireless Microphone Package
Velcro 2
+
Quick Start
USB Cable
Dongle
VCM60 Power
Adapter Guide
AAA Batteries 2
+
Remote Control
+
+
4
+
2
VC110 All-in-one Unit
Cable Hub
VCC110 Mounting Accessories
Ethernet Cable
(7.5m)
Please use the Yealink-customized DVI cable (only for VC110)
VC110 all-in-one unit can work with the video conferencing microphone array, video conferencing wireless
microphone or video conferencing phone. You can purchase any combination according to your needs.
+
CPE80 Expansion
Microphone 2
Video Conferencing
Phone
Ethernet Cable
(7.5m)
Video Conferencing Phone Package
3.5mm Audio Cable

VC110 All-in-one Unit Connection Diagram
2
The Back of the VC110
Please connect to Display1 port in blue color if you have only one display device
HDMI CableDVI Cable
Display 2
+
Cable Hub

3
The VCM60 video conferencing wireless microphone and dongle are automatically ”paired” at the factory. All you need
to do is connect the dongle to one of the USB ports on the VC110 all-in-one unit. After the VCM60 is turned on, the
VCM60 will register with the dongle automatically.
VCM60 Video Conferencing
Wireless Microphone
Dongle
The Right Side of the VC110
For more information, refer to Yealink VCM60 Video Conferencing Wireless Microphone Quick Start Guide

Remote Control and Cable Ties Installation
Fasten the cables with the cable tie
Install batteries
4

VC110 All-in-one Unit Installation
Hanging Mode
5
Please choose the following installation mode when the thickness of the TV is between 35-120mm.
TV
4
1
3
2
Adjust the bracket to ensure close adhesion to the back of the TV.
1
Steps:
Make sure the back of the TV is clean, and then adjust the bracket to ensure close adhesion to the back of
33
2Remove the protection of the Velcro. Put the L-bracket on the
4
the TV with Velcro.
Lock the VC110 all-in-one unit to the L-bracket.
top of the TV.

Wall-mount Mode
Steps：Punch holes & Insert expansion bolts Drive screws Adjust the screw position and manually
lock it Insert screws to lock the bracket to the wall Connect DVI cable Lock the camera
12 3
4 5 6
6
Hole diameter: 6mm
Hole depth: 30mm
Screw specification: M3 8
50mm
100mm 4
13
2
+
Screw specification: T4 30
+
5 6
The recommended height for VC110 all-in-one unit positioning is 1.5m-1.8m

7
Wall Mount Method for the Cable Hub
DVI Cable
DVI
83mm
Cable Hub Connection Diagram
+
The cable hub can also be powered from a PoE-compliant switch or hub.
The VC110 video conferencing endpoint should be used with Yealink original power adapter (12V/2A) only.
Connect to a video conferencing phone or VCM30 audio device
(2m)
Ethernet Cable
(7.5m)
Ethernet Cable
video conferencing phone
Power Adapter
VCM30
PC
VGA Cable
To hang the cable hub on the wall, you need to purchase the screws (specification: T4 30) separately.

Main Screen
Time and date Site name Status icon Endpoint IP address and
account information
8

Network Deployment
Yealink Cloud Deployment
VC110 supports two network deployment methods: Yealink Cloud deployment and traditional deployment. Choose the
desired deployment method according to your needs.
. Select Menu->Advanced (Admin Password:0000)->Yealink Cloud
.
Select desired sign-in method from the pull-down list of Login Type
1）You can sign into the 9-digit enterprise Cloud account using PIN code or username/password (enterprise Cloud
account can be managed via Yealink VC Cloud Management Service)
2）You can also use 7-digit build-in Cloud number (build-in Cloud number cannot be managed via Yealink VC Cloud
Management Service)
With Yealink VC Cloud management service, organizations can communicate just using a Cloud account. Both the head
office and the branch offices can use this deployment method. Get Cloud account information from your Cloud enterprise
administrator, and do the following to sign into your VC110 via remote control:
9

Head Office
If you deploy VC110 in the head office, at least one static public IP address is required in the head office to allow branch
offices to connect. Do one of the following to deploy VC110:
Configure a Static IP
The following introduces how to configure a static IP address for the VC110.
Select Menu->Advanced (Admin Password:0000)->LAN Configuration
10
Select IPv4 from the IP Mode pull-down list
Select IPv4
Option2: To deploy the VC110 in an Intranet (behind the firewall), you must assign a static private IP address to the
VC110. In the meantime, do port mapping on the firewall for VC110.
Traditional Deployment
Option1: To deploy the VC110 on a public network, at least one static public IP address is required, you need to assign
a static public IP address to the VC110.
Turn off the DHCP
.
If you do not use Cloud accounts, you can choose traditional deployment method to deploy your VC110, and dial IP
addresses of other devices to make a call.
In order to ensure that the VC110 can work properly, please configure it according to the role it plays in the meeting.
If it is in the head office, please make sure that it is reachable from public network. If it is in branch office, please use
intelligent firewall traversal to deploy it or just follow the same steps as for the head office.
.
.
.
For example: use the remote control to configure a static IPv4 address to your VC110.

Configure Port Mapping
If the VC110 is deployed in an Intranet, and you want to solve the interconnection problem by port mapping, you must
forward the following ports to the public network on the firewall.
. Press Save to save the configuration,
. The screen prompts Reboot now
. Press OK to reboot the endpoint .
PortFunction
H.323 signal port
SIP（optional ）
Audio & Video media stream port
Web management port（optional ）
Protocol Type
UDP/TCP
5060
443
50000-50499
1719-1720
TCP/UDP
TCP/UDP
TCP
Enter the IP address, subnet mask, gateway and DNS information in corresponding fields.
.
11

Branch Office
If you delpoy VC110 in the branch office, do one of the following to deploy it:
Option1: Deploy the VC110 following the same steps as for the head office. In this way, both inbound and outbound calls
will be available.
Option2: Deploy the VC110 using an intelligent firewall, which means that plug and play is possible without any further
firewall configuration, but only outbound calls are available.
Please note that when the VC110 is deployed with an intelligent firewall, you have to open ports (as shown below)
permission if they are restricted
It is recommended that you forward the web management port(443/TCP) to the public network, so that the head
office can remotely manage the branch office.
PortFunction
H.323 signal port
SIP（optional ）
Audio & Video media stream port
Protocol Type
UDP/TCP
TCP/UDP
TCP/UDP
50000-50499
5060-5061
1719-1720
12

Video Resolution Recommended Bandwidth
Full HD 1080P 1.3Mb
People 1080P+Content 1080P 2.6Mb
Bandwidth Requirements
To ensure the performance of video conference, the recommended bandwidth for VC110 is as
below:
For more information of the configurations, contact your system administrator.
The bandwidth mentioned above is based on two-way conference. Bandwidth in head office should be increased
along with the growing number of connected branch offices .
Troubleshooting
After the installation and deployment, you can test the VC110 by dialing Yealink Demo Room. If you can’t dial out
successfully, please contact your IT administrator to check the internal network configuration.
Assume that you are A in head office and use the configuration method in "Head Office" chapter on page 10, you are
able to call B in branch office or Yealink Demo, but they cannot reach you. The most likely reason is the firewall or
gateway in the environment does not support H.323 ALG feature. In this situation, please take the following actions
so that the NAT feature on the VC110 can solve this problem.
13

Yealink Test Room IP: 117.28.251.50、117.28.251.51
. Select Menu->Advanced (Admin Password:0000)->NAT/Firewall
. Select Auto from the Type pull-down list, the endpoint will obtain public IP address automatically.
If the endpoint does not obtain a public IP address automatically, select Manual Settings from the Type pull-down list,
.
and then enter the public IP address in the Public IP Address field.
To configure NAT via the remote control:
14

For more information, visit the Yealink website:
www.yealink.com
YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD.
Web: www.yealink.com | Addr: 309, 3th Floor, No.16, Yun Ding North Road, Huli District, Xiamen City, Fujian, P.R. China | Copyright ©2016Yealink Inc.All right reserved.