Yealink VC120 User manual

Yealink VC120 Video Conferencing System Quick Start Guide
Applies to firmware version 40.22.0.15 or later
V22.15
Yealink Network Technology CO., LTD

Table of Contents
Packaging Contents 01
VC120 Connections 02
Remote Control and Cable Ties Installation 04
Bracket and Camera Installation 05
Main Screen 07
Network Deployment 08
Troubleshooting 12

Power Adapter
(2m)
DVI Cable HDMI Cable 2 Ethernet Cable
Velcro 2
+
+
AAA Batteries 2
+
Camera VC120 Codec VCR10 Remote Control
Cable Ties 5
+
Quick Start Guide
Please use the Yealink-customized DVI cable.
We recommend that you use the accessories provided or approved by Yealink. The use of unapproved third-party
accessories may result in reduced performance.
CPE80 Expansion
Microphone 2
VC120 video conferencing system can work with the video conferencing phone or video conferencing microphone
array. You can purchase any combination according to your needs.
Camera Mounting Accessories
HDMI-VGA Direct Cable
Video Conferencing
Phone
Ethernet Cable
(7.5m)
Ethernet Cable
(7.5m)
VCM30
Microphone Array Package
Video Conferencing Phone Package
+
3.5mm Audio Cable
Packaging Contents
1

VC120 Connections
Camera
HDMI Cable 2m Ethernet Cable Power Adapter
PC Display 2
DVI Cable
+
7.5m Ethernet Cable
CPE80 CPE80
Video Conferencing Phone
2
The video conferencing phone is used to be the audio input/output device:
HDMI-VGA Direct Cable

The VCM30 microphone array is used to be the audio input device:
Please connect to the Display1 port if you only have one display device
The system should be used with Yealink original power adapter (19V/3.42A) only. The use of the third-party power
Camera
HDMI Cable 2m Ethernet Cable Power Adapter
PC Display 2
DVI Cable
+
VCM30
7.5m Ethernet Cable
HDMI-VGA Direct Cable
adaptermay cause the damage to the system
3

Remote Control and Cable Ties Installation
4
Fasten the cables with the cable tie
Install batteries

Bracket and Camera Installation
Please chose the following installation mode when the thickness of the TV is between 35-120mm
Hanging Mode
Adjust the bracket to ensure close adhesion to the back of the TV
Lock the camera to the L-bracket.
1
Steps:
Make sure the back of the TV is clean, and then adjust the bracket to ensure close adhesion to the back of the TV
33
2
5
TV
4
3
1
2
Remove the protection of the Velcro. Put the L-bracket on the top of the TV.
with Velcro.
4

The recommended height for camera positioning is 1.5m-1.8m above the ground
Wall Mount Method
Hole diameter: 6mm
Hole depth: 30mm
50mm
100mm 4
1
3
2Screw specification: M3 8
+
Screw specification: T4 30
+
Steps：Punch holes & Insert expansion bolts Drive screws Adjust the screws position and manually lock them
13
6
2
5
5 6
Insert screws to lock the bracket to the wall Connect DVI cable Lock the camera
4
6

Main Screen
7
Time and date Site name Status icon System IP address and
account information

Network Deployment
8
VC120 supports two network deployment methods: Cloud deployment and traditional deployment. Choose the desired
deployment method according to your needs.
Cloud Deployment
Select Menu->Advanced (Default Admin Password:0000)->Cloud.
In the Cloud Account filed, check the Enabled checkbox.
Select the desired platform from the pull-down list of Platform Type.
.
.
.
Configure the desired platform.
.
With Cloud service, organizations can communicate using the Cloud platform, so that complex network settings are
unnecessary. Both the head office and the branch offices can use this deployment method. You can log into Yealink
Cloud/StarLeaf/Zoom/Pexip/BlueJeans/Mind/Custom platform using VC120 video conferencing system. Get account
information from your administrator. Do the following to log into your VC120 via remote control: