Zamel exta PB Series User manual

PBP - 03 BISTABLE RELAY INSTRUCTION MANUAL
Zakład Mechaniki i Elektroniki
ZAMEL sp.j.
J.W. Dzida, K. Łodzińska
ul. Zielona 27, 43-200 Pszczyna, Poland
Tel. [phone], Fax [phone]
www.zamelcet.com, e-mail: [email protected]
APPERANCE
FEATURES
DESCRIPTION
ی Bistable lighting control,
ی Time limit function,
ی Soft start and switch-off (0.8 s),
ی Load ON indicator – red LED,
ی Device triggering by means of the L
wire,
ی Applicable together with the single
pole push buttons, illuminated,
ی Two-conductor control system,
ی Easy applicable together with any
existing electrical system,
ی Supplied in series with load.
The PBP-03 bistable relay is designed
for lighting or any other unit by means of
single pole push buttons connected in
parallel. Successive pressing of any but-
ton causes switching ON / OFF the load
connected to the output terminals alterna-
tively. The L line is a source of a control
impulse. After the impulse has arrived
t delay time will be measured and then,
the load will be OFF. It is possible to
mount the device under a push button, in
a deep junction box of 60 mm diameter.
TECHNICAL DATA
PBP - 03
Power terminals: L (black), brown – in series with the load
Rated voltage: 230 V
Rated voltage tolerance: -15 ÷ +10 %
Rated frequency: 50 Hz
Rated current: 8 mA
Load supply indicator: red LED
Trigger conductor: IN (red)
Load supply: brown
ON-time adjustment range: 10 s ÷ 16 min
ON-time setting accuracy: ±3 %
ON-time setting repeatability: ±5 %
ON-time setting: continuous (rotary potentiometer)
Permissible load: 30 ÷ 300 W
Fuse technical specication: 5 x 20 mm, ultra-fast, 2 A / 250 V
Control: triac
Connection wires quantity: 3
Connection wire section: 1 mm2
Operating temperature: -20 ÷ +45 oC
Operating position: optional
Casing fastening: for 60 mm junction box
Casing IP: IP40
Protection class: II
Overvoltage category: II
Pollution level: 2
Dimensions: 50 x 50 x 15 mm
Weight: 28 g
Standard conformity: PN-EN 60669-1, PN-EN 60669-2-1,
PN-EN 61000-4-2,3,4,5,6,11
Load ON indicator
Load power lead
Power lead (L)
Fuse socket
Trigger conductor (IN)
ON-time adjustment
b
r
o
w
n
r
e
d
b
l
a
c
k
The timer should be
connected to a single-
phase system accordin-
gly to current standards.
The device connections
will be described in this
manual. Only qualied electricians are
allowed to assembly, connect and ad-
just the timer. It is necessary to read this
manual before the timer mounting. Do
not disassembly the timer casing or you
will lose any warranty rights and expo-
se yourself to the electric shock hazard.
Before mounting operation make sure
of disconnecting the connection wires
from the electric network. The timer
should be carried, stored and used in
an appropriate way. Do not mount the
timer in case of any device parts lack,
damage or deformation. In case of mal-
function please notify the manufacturer.
CAUTION

APPLICATION
ASSEMBLY, OPERATION
CASING DIMENSIONS
UNIT DIAGRAM
1. Disconnect the electric network by means
of an appropriate cut-off, current-limiting
circuit-breaker or a separator.
2. Check if there is no any voltage between
power leads.
3. Mount the PBP-03 device in the 60 mm
junction box.
4. Connect wires accordingly to electrical
diagram.
5. Connect power supply circuit.
The unit is designed for lighting control of
power up to 350 W. A single pole push button
is used for the light control. If needed, it is po-
ssible to connect the push buttons in parallel
and control the lights from various places. The
push button pressing causes the light switching
ON / ONN alternatively. When the light bulbs
are OFF, pressing the push button causes soft
switching ON the light (0.8 s). The soft start
elongates the bulbs life. There are two ways of
the light switching-OFF: – successive pressing
the push button, – waiting until the preset time
is over (automatic). The ligh is OFF softly, too
(0.8 s).
CONNECTIONS
TIME DIAGRAMS
LOAD
PRODUCT FAMILY
The PBP-03 bistable relay is a member
of the PBX product family.
A typical assembly exam-
ple with the PBP-03 bi-
stable relay with time limit
function.
A single pole bell-push is
applied in the unit.
μC
t t
b
r
o
w
n
r
e
d
b
l
a
c
k
b
r
ą
z
o
w
y
c
z
e
r
w
o
n
y
c
z
a
r
n
y
24 V AC/DC supply version
available for PMB-01,
PMB-02, PMB-03
Device version:
01 – basic
02 – extended: SET, RESET
functions and state storage
03 – with time limit function
Casing type:
M –single-module
P – for junction box
Device type
WARRANTY
The product warranty is for a period of 24 months
Dealer signature & stamp, purchase date
1. ZMIE ZAMEL SP. J. assures 24 months guarantee for the product.
2. The manufacturer’s guarantee does not cover any of the following actions:
a) mechanical damage during transport, loading / unloading or under other circumstances,
b) damage caused by incorrect product mounting or misuse,
c) damage caused by unauthorised modications made by the PURCHASER or any third parties to the product or any other devices
needed for the product functioning,
d) damage caused by Act of God or any other incidents independent of the manufacturer.
3. The PURCHASER shall lay any claims in writing to the dealer or ZMIE ZAMEL SP. J.
4. ZMIE ZAMEL SP. J. is liable for processing any claim according to current Polish legislation.
5. ZMIE ZAMEL SP. J. shall process the claim at its own discretion: product repair, replacement or money return.
6. The manufacturer’s guarantee is valid in the Republic of Poland.
7. The PURCHASER’s statutory rights in any applicable legislation whether against the retailer arising from the purchase contract or
otherwise are not affected by this warranty.