Abus Secvest FU8006 User manual

Secvest QuickGuide installation
Secvest QuickGuide installationSecvest QuickGuide installation
Secvest QuickGuide installation
Please observe all country-specific safety instructions. The 230 V ains
power supply should only be connected by trained specialist
personnel.
 Re ove both housing screws fro the botto side of the
Secvest.
 Fold the front housing side upwards and carefully pull the
ribbon cable fro the PSU.
 Fix the base plate on a suitable surface using the screws and
wall plugs provided.
 Overview of the base plate:
No. Description
1 Cable clamp (tension relief) for the 230 V AC mains line
2 Connection socket for the connection cable
3 230 V AC mains connection
4 Connection clamps for wired zones and outputs
 Install the 230 V ains connection with the power supply
disconnected and attach the cable cla ps.
 Optional:
Optional:Optional:
Optional: Install the wired detectors to the zone inputs using
the resistors provided and/or connect the relay outputs, when
required. For further infor ation, consult the installation
instructions.
 Overview of the rear side of the Secvest:
 Optional:
Optional:Optional:
Optional: Connection for external loudspeaker (16 Oh ) and
external icrophone -> ite no. FU5230
 Optional:
Optional:Optional:
Optional: To use the integrated dialler, connect the analogue
line to the A/B connections. The return line can be connected
to A1/B1. The C/E connections are not used.
  
  
 

No. Description
1 Internal siren
2 Battery compartment
3 Internal loudspeaker
4 Connection for the analogue telephone line (PSTN)
5 Kickstart and Codes Defaulted jumper (KS + RESET)
6 Connection for external loudspeaker and microphone
7 Connection for extension modules (ISDN / GSM / ethernet /
GPRS)
8 Connecting cable between base plate and top part
9 Loudspeaker volume control
10 USB port

Ta per contact
Front and
rear side
Press the t
est
button for about
10 seconds
Press the key for
around 2 seconds
until the red LED
Press the key for
around 1 second,
then turn the knob
 Insert the batteries with the correct polarity.
 Close the unused cable inputs using the plugs
provided.
 Suspend the centre at the top of the base plate and
reconnect the ribbon cable to the connection in the base plate. Fold
the front housing side downwards and fasten it using the two housing
screws.
 Attach the ains power supply to the centre.
IMPORTANT:
When starting the centre for the first ti e, you will
be pro pted to select your language.
Secvest
SecvestSecvest
Secvest QuickGuide progra ing
QuickGuide progra ing QuickGuide progra ing
QuickGuide progra ing
There is a difference between the installer enu and user enu when progra ing the centre. A user code and an installer code are required. To access the installer enu, press
the key under the “Menu” display. Enter your installer code (7890
78907890
7890) and then the user code (1234
12341234
1234). Follow the instructions in the display to train the wireless detector. Detailed
infor ation can be found in the installation instructions.
Insert the batteries in the detector, then press the ta per contact on the detector (open). The centre acknowledges reception with a confir ation tone.
If a false alar is triggered accidentally, then this can be acknowledged by entering the ad inistrator code (1234
12341234
1234). The syste does not react to ta per essages when the installer
enu is accessed. This eans that all detectors can be opened without triggering an alar . So e exa ples of training detectors are found below. When other detectors are used,
consult the corresponding anuals for further infor ation. Details on progra ing the zone settings can be found in the installation instructions.
The user enu ust be accessed in order to change user codes and train chip keys, wireless cylinders or re ote control units. Leave the installer enu and access the user enu by
pressing “Menu”, then entering the ad inistrator code (1234
12341234
1234).
For exa ple, select “Teleco ands” in the enu to assign a re ote control unit to this user. The SecvestKey wireless cylinder is also trained in this enu.
Tamper contact
(wall break contact)