ACME Glamour 350Z User manual

CONTENTS
1. Safety Instructions ......................................................................................... 2
2. Technical Specifications ................................................................................. 4
3. How To Set The Unit....................................................................................... 5
3.1 Control Panel ........................................................................................... 5
3.2 Main Function.......................................................................................... 6
3.3 Home Position Adjustment .................................................................... 13
4. Control By Universal DMX Controller ........................................................... 14
4.1 DMX512 Connection.............................................................................. 14
4.2 Address Setting ...................................................................................... 15
4.3 DMX512 Configuration........................................................................... 15
5. Troubleshooting........................................................................................... 21
6. Fixture Cleaning ........................................................................................... 22
1H

1. Safety Instructions
WARNING
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer
will not accept liability for any resulting defects or problems.
Unpack and check carefully that there is no transportation damage before using the unit.
This product is for indoor use only. Use only in a dry location.
DO install and operate by qualified operator.
DO NOT allow children to operate the fixture.
Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head
only.
The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces.
Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.
Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.
DO NOT connect the device to any dimmer pack.
During initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective, and it will decrease gradually within 15 minutes.
Make sure there are no flammable materials close to the unit while operating to avoid fire
hazard.
Examine the power wires carefully; replace them immediately if there is any damage.
Please read the instruction carefully which includes important information about
the installation, usage and maintenance.
2H

Unit’s surface temperature may reach up to 75℃. DO NOT touch the housing bare-handed
during its operation.
Avoid any inflammable liquids, water or metal objects entering the unit. Once it happens, cut
off the mains power immediately.
DO NOT operate in dirty or dusty environment, do clean fixtures regularly.
DO NOT touch any wire during operation as there might be a hazard of electric shock.
Avoid power wires together twist other cables.
The minimum distance between light output and the illuminated surface must be more than
12 meters.
Disconnect mains power before fuse replacement or servicing.
Replace fuse only with the same type.
In the event of serious operating problem, stop using the unit immediately.
Never turn on and off the unit time after time.
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
DO NOT open the unit as there are no user serviceable parts inside.
Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance center if
needed.
Disconnect the mains power if the fixture is has not been used for a long time.
DO use the original packing materials before transporting it again.
DO NOT look directly at the light while the LED is on.
DO NOT start on the unit without LED enclosure or when housing is damaged.
Installation:
The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the
unit is firmly fixed to avoid vibration and slipping while operating and make sure that the structure
to which you are attaching the unit is secure and is able to support a weight of 10 times of the
fixtures weight. Always use a safety cable that can hold 12 times of the weight of the fixture when
installing.
The equipment must be installed by professionals. It must be installed in a place where is out of
the reach of people and no one can pass by or under it.
3H

2. Technical Specifications
Power Voltage:
AC 100~240V, 50/60Hz
Power Consumption:
315W (CM-350Z II)
320W (CM-350Z III)
Light Source:
7x40W RGBW LED
Zoom Range:
5°~50°
Movement:
Pan: 540°
Tilt: 225°
Pan/Tilt Resolution: 16bit
Dimming/Strobe:
0~100% smooth dimming, variable strobe effects
Control:
DMX Channel: 1 1/1 5/14 Channels
Control Mode: DMX, Wireless Control (Optional)
Firmware Upgrade: Update via DMX link
Construction:
Display: LCD Display
Data In/Out: 3-pin&5-pin XLR
Power In/Out: Power Connector in/out
Protection Rating: IP20
Features:
Motorized liner zoom system
Outstanding color macro effect
Fast, quiet, flicker free operation
4H

Dimension/Weight:
310x226x412mm, 10.6kgs
12.2"x8.9"x16.2"in, 23.4lbs
310 mm
412 mm
226 mm
Photometric Diagram:
3. How To Set The Unit
3.1 Control Panel
1. Display: To show the various menus and the selected functions
5H

2. LED:
POWER ON Power On
DMX ON DMX input present
3. Button:
MENU To enter into move backward or leave the menu
DOWN To go forward in the selected functions
UP To go backward in the selected functions
ENTER To confirm the selected functions
4. DMX IN:
DMX512 link, use 3/5-pin XLR cable to link the unit and the DMX controller to input DMX signal
5. DMX OUT:
DMX512 link, use 3/5-pin XLR cable to link the next unit to output DMX signal
6. MAINS IN:
To connect to the mains supply
7. MAIS OUT:
To connect to the next unit
8. Fuse (T 6.3A):
Protects the unit from over-voltage or short circuit
3.2 Main Function
To select any of the given functions, press the MENU button until the required function is showing
on the display. Select the function by pressing the ENTER button and the display will blink. Use the
DOWN/UP buttons to change the mode. Once the required mode has been selected, press the
ENTER button to setup, to go back to the functions without any change press the MENU button
again. Press and hold the MENU button for about one second or wait for one minute to exit the
menu mode.
The main functions are shown overleaf:
6H

7H

DMX Functions
Enter MENU mode, select DMX Functions, press the ENTER button to confirm, use the UP/DOWN
button to select DMX Address, DMX Channel Mode, View DMX Value or WDMX Setting.
DMX Address
To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to adjust
the address from 001 to 512, press the ENTER button to setup. Press the MENU button back to the
last menu or let the unit idle one minute to exit menu mode.
DMX Channel Mode
To select DMX Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to
select Mode1 (11), Mode2 (15) or Mode3 (14), press the ENTER button to setup. Press the MENU
button back to the last menu or let the unit idle one minute to exit menu mode.
View DMX Value
To select View DMX Value, press the ENTER button to confirm. Use the UP/DOWN button to view
the DMX channel values. Press the MENU button back to the last menu or let the unit idle one
minute to exit menu mode.
WDMX Setting
To select WDMX Setting, press the ENTER button to confirm. Use the UP/DOWN button to select
Active, Retransmit, Reset Memory or WDMX Channel, press the ENTER button to setup. Press the
MENU button back to the last menu or let the unit idle one minute to exit menu mode.
Fixture Setting
Enter MENU mode, select Fixture Setting, press the ENTER button to confirm, use the UP/DOWN
button to select Pan Inverse, Tilt Inverse, P/T Feedback,BL.O. P/T Moving, White Balance,
Cooling Mode,Dimmer Curve or Dimmer Speed.
Pan Inverse
To select Pan Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select No
(normal) or Yes (pan inverse), press the ENTER button to setup. Press the MENU button back to
the last menu or let the unit idle one minute to exit menu mode.
8H

Tilt Inverse
To select Tilt Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select No
(normal) or Yes (tilt inverse), press the ENTER button to setup. Press the MENU button back to the
last menu or let the unit idle one minute to exit menu mode.
P/T Feedback
To select P/T Feedback, press the ENTER button to confirm. Use the UP/DOWN button to select
No (Pan or tilt’s position will not feedback while out of step) or Yes (Feedback while pan/tilt out of
step), press the ENTER button to setup. Press the MENU button back to the last menu or let the
unit idle one minute to exit menu mode.
BL.O. P/T Moving
To select BL.O. P/T Moving, press the ENTER button to confirm. Use the UP/DOWN button to
select No (normal while pan/tilt moving) or Yes (blackout while pan/tilt moving), press the ENTER
button to setup. Press the MENU button back to the last menu or let the unit idle one minute to
exit menu mode.
White Balance
To select White Balance, press the ENTER button to confirm. Use the UP/DOWN button to select
Red, Green or Blue, press the ENTER button to setup. Press the MENU button back to the last
menu or let the unit idle one minute to exit menu mode.
Cooling Mode
To select Cooling Mode, press the ENTER button to confirm. Use the UP/DOWN button to select
Auto or Low. Once selected, press the ENTER button to setup. Press the MENU button back to the
last menu or let the unit idle one minute to exit menu mode.
Dimmer Curve
To select Dimmer Curve, press the ENTERbutton to confirm. Use the UP/DOWN button to select
Linear, Square Law, Inverse Squ. or S-Curve. Once selected, press the ENTER button to store.
Press the MENU button back to the last menu or let the unit idle one minute to exit menu mode.
9H

Linear: The increase in light intensity appears to be linear as DMX value is increased.
Square Law: Light intensity control is finer at low levels and coarser at high levels.
Inverse Square Law: Light intensity control is coarser at low levels and finger at high levels.
S-cure: Light intensity control is finger at low levels and high levels and coarser at medium levels.
Dimmer Speed
To select Dimmer Speed, press the ENTER button to confirm. Use the UP/DOWN button to select
Fast or Smooth. Once selected, press the ENTERbutton to setup. Press the MENU button back to
the last menu or let the unit idle one minute to exit menu mode.
Display Setting
Enter MENU mode, select Display Setting, press the ENTER button to confirm, use the UP/DOWN
button to select Display Inverse, Backlight Auto Off, Backlight Intensity, Contrast Ratio,
Temperature Unit, Display Warning or Language.
Display Inverse
To select Display Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select
No (normal) or Yes (display inverse). Once selected, press the ENTER button to store. Press the
MENU button back to the last menu or let the unit idle one minute to exit menu mode.
Backlight Auto Off
To select Backlight Auto Off, press the ENTER button to confirm. Use the UP/DOWN button to
select No (display always on) or Yes (display goes off one minute after exiting menu mode). Once
selected, press the ENTER button to confirm and store. Press the MENU button back to the last
menu or let the unit idle one minute to exit menu mode.
10H

Backlight Intensity
To select Backlight Intensity, press the ENTER button to confirm. Use the UP/DOWN button to
adjust the intensity from 1 (dark) to 10 (bright). Once selected, press the ENTER button to setup
and store. Press the MENU button back to the last menu or let the unit idle one minute to exit
menu mode.
Contrast Ratio
To select Contrast Ratio, press the ENTER button to confirm. Use the UP/DOWN button to adjust
the intensity from 1to 30. Once selected, press the ENTER button to setup and store. Press the
MENU button back to the last menu or let the unit idle one minute to exit menu mode.
Temperature Unit
To Select Temperature Unit, press the ENTER button to confirm. Use the UP/DOWN button to
select
℃
or
℉
, press the ENTER button to store. Press the MENU button back to the last menu
or let the unit idle one minute to exit menu mode.
Display Warning
To select Display Warning, press the ENTER button to confirm. Use the UP/DOWN button to select
No (Normal) or Yes (display will show the error warning when the unit went wrong), press the
ENTER button to store. Press the MENU button back to the last menu or let the unit idle one
minute to exit menu mode.
Language
To select Language, press the ENTER button to confirm. Use the UP/DOWN button to select
English or Chinese, press the ENTER button to store. Press the MENU button back to the last menu
or let the unit idle one minute to exit menu mode.
F ixture Test
Enter MENU mode, select F ixture Test, press the ENTER button to confirm, use the UP/DOWN
button to select Auto Test or Manual Test
Auto Test
To select Auto Test, press the ENTER button to confirm, the unit will run built-in programs to
automatically test pan, tilt, zoom and etc. Press the MENU button back to the last menu or exit
11H

menu mode after auto test.
Manual Test
To select Manual Test, press the ENTER button to confirm. Use the UP/DOWN button to select
channel, and adjust the channel value. Once selected, press the ENTER button to setup, the fixture
will run as the channel value indicates. Press the MENU button back to the last menu or exit menu
mode let the unit idle one minute.
(All channels value will become 0 after exiting Manual Test menu)
Fixture Information
Enter MENU mode, select Fixture Information, press the ENTER button to confirm, use the
UP/DOWN button to select Fixture use time or Firmware Version.
Fixture use time
To select Fixture use time, press the ENTER button to confirm, the fixture working hours will show
on the display. Press the MENU button to exit.
Firmware Version
To select Firmware Version, press the ENTER button to confirm, the fixture software version will
show on the display. Press the MENU button to exit.
Reset Functions
Enter MENU mode, select Reset Functions, press the ENTER button to confirm, use the UP/DOWN
button to select Pan/Tilt, Zoom or All.
Pan/Tilt
To Select Pan/Tilt, press the ENTER button to confirm. Use the UP/DOWN button to select No or
Yes (the unit will run built-in program to reset pan and tilt to their home positions), press the
ENTER button to store. Press the MENU button to exit menu mode.
Zoom
To select Zoom, press the ENTER button to confirm. Use the UP/DOWN button to select No or Yes
(the unit will run built-in program to reset zoom to its home positions), press the ENTER button to
store. Press the MENU button to exit menu mode.
12H

All
To select All, press the ENTER button to confirm. Use the UP/DOWN button to select No or Yes
(the unit will run built-in program to reset all motors to their home positions), press ENTER button
to store. Press MENU button to exit menu mode.
Special Functions
Enter MENU mode, select Special Functions, press the ENTER button to confirm, use the
UP/DOWN button to select Fixture Maintenance or Factory Setting.
Fixture Maintenance
To select Fixture Maintenance, press the ENTER button to confirm. Use the UP/DOWN button to
select Interval or Remain Time, Press the ENTER button to confirm, press the MENU button to
exit.
Factory Setting
To select Factory Setting, press the ENTER button to confirm. Use the UP/DOWN button to select
No or Yes (the fixture will reset to factory settings and exit menu mode).
3.3 Home Position Adjustment
In the main functions, hold the ENTER button for at least 3 seconds into offset mode, use the
DOWN/UP button up to select Pan, Tilt or Zoom, and press the ENTER button to confirm. Use the
DOWN/UP button to adjust the home position of the Pan, Tilt or Zoom, once the position has
been selected, press the ENTER button to setup, to go back to the functions without any change
press the MENU button again. Press and hold the MENU button about one second or wait for
about one minute to exit the menu mode.
13H

4. Control By Universal DMX Controller
4.1 DMX512 Connection
1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin adapter-cable.
2. The last units DMX cable has to be terminated with a 120 ohm 1/4W resistor between pin
2(DMX-) and pin 3(DMX+) of a 3-pin XLR-plug and plug it in the DMX-output of the last unit.
3. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to the
input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is a very
high-speed signal. Inadequate or damaged cables, soldered joints or corroded connectors can
easily distort the signal and shut down the system.
4. The DMX output and input connectors are pass-through to maintain the DMX circuit, when
one of the units’ power is disconnected.
5. Each fixture unit needs to have an address set to receive the data sent by the controller. The
address number is between 0-511 (usually 0 & 1 are equal to 1).
14H

6. The end of the DMX 512 system should be terminated to reduce signal errors.
7. 3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+),
Pin 4/Pin 5: Not used.
4.2 Address Setting
If you use a universal DMX controller to control the units, you have to set DMX address from 1 to
512 so that the units can receive DMX signal.
Press the MENU button to enter menu mode, select DMX Functions, press the ENTER button to
confirm, use the UP/DOWN button to select DMX Address, press the ENTER button to confirm,
the present address will blink on the display, use the UP/DOWN button to adjust the address from
001 to 512, and press the ENTER button to store. Press the MENU button back to the last menu or
let the unit idle 7 seconds to exit menu mode.
Please refer to the following diagram to set the DMX address for the first 4 units:
Channel mode
Unit 1
Address
Unit 2
Address
Unit 3
Address
Unit 4
Address
11 channels 1 12 23 34
15 channels 1 16 31 46
14 channels 1 15 29 43
4.3 DMX512 Configuration
11 Channels Mode:
CHANNEL VALUE FUNCTION
1
000-255
PAN
0%

100%
2
000-255
TILT
0%

100%
3 PAN/TILT SPEED
15H

000-255
fast

slow
4
000-019
020-024
025-064
065-069
070-084
085-089
090-104
105-109
110-124
125-129
130-144
145-149
150-164
165-169
170-184
185-189
190-204
205-209
210-224
225-229
230-244
245-255
SHUTTER
Off
Open
Strobe: fast to slow
Open
Fast close slow open
Open
Fast open slow close
Open
Random strobe
Open
Random fast close slow open
Open
Random fast open slow close
Open
Burst pulse
Open
Random burst pulse
Open
Slow close slow open
Open
Burst
Open
5 000-255 RED (0%100%)
6 000-255 GREEN (0%100%)
7 000-255 BLUE (0%100%)
8 000-255 WHITE (0%100%)
9
000-255
DIMMER
0%

100%
10
000-255
ZOOM
0%

100%
11
000-009
010-014
015-255
SPECIAL FUNCTIONS
No function
Reset all
No function
16H

15 Channels Mode:
CHANNEL VALUE FUNCTION
1
000-019
020-024
025-064
065-069
070-084
085-089
090-104
105-109
110-124
125-129
130-144
145-149
150-164
165-169
170-184
185-189
190-204
205-209
210-224
225-229
230-244
245-255
SHUTTER
Off
Open
Strobe: fast to slow
Open
Fast close slow open
Open
Fast open slow close
Open
Random strobe
Open
Random fast close slow open
Open
Random fast open slow close
Open
Burst pulse
Open
Random burst pulse
Open
Slow close slow open
Open
Burst
Open
2
000-255
DIMMER
0%

100%
3
000-255
ZOOM
0%

100%
4
000-255
PAN
0%

100%
5 000-255 PAN FINE
6
000-255
TILT
0%

100%
7 000-255 TILT FINE
8
000-255
PAN/TILT SPEED
fast

slow
9
000-009
010-014
015-255
SPECIAL FUNCTIONS
No function
Reset all
No function
17H

10
000-009
010-014
015-019
020-024
025-029
030-034
035-039
040-044
045-049
050-054
055-059
060-064
065-069
070-074
075-079
080-084
085-089
090-094
095-099
100-104
105-109
110-114
115-119
120-124
125-129
130-134
135-139
140-144
145-149
150-154
155-159
160-164
165-169
170-174
175-179
180-201
202-207
208-229
230-234
235-239
240-244
245-249
250-255
COLOR
Open
Color1
Color2
Color3
Color4
Color5
Color6
Color7
Color8
Color9
Color10
Color11
Color12
Color13
Color14
Color15
Color16
Color17
Color18
Color19
Color20
Color21
Color22
Color23
Color24
Color25
Color26
Color27
Color28
Color29
Color30
Color31
Color32
Color33
Open
CCW Rotation: fast to slow
Stop
CW Rotation: slow to fast
Open
Random color rotation (fast speed)
Random color rotation (medium speed)
Random color rotation (slow speed)
Open
18H

11 000-255 RED (0%100%)
12 000-255 GREEN (0%100%)
13 000-255 BLUE (0%100%)
14 000-255 WHITE (0%100%)
15
000-255
CTO
0%

100%
14 Channels Mode:
CHANNEL VALUE FUNCTION
1
000-255
PAN
0%

100%
2 000-255 PAN FINE
3
000-255
TILT
0%

100%
4 000-255 TILT FINE
5
000-255
PAN/TILT SPEED
fast

slow
6
000-009
010-014
015-255
SPECIAL FUNCTIONS
No function
Reset all
No function
7
000-255
DIMMER
0%

100%
8
000-019
020-024
025-064
065-069
070-084
085-089
090-104
105-109
110-124
125-129
130-144
145-149
150-164
165-169
170-184
SHUTTER
Off
Open
Strobe: fast to slow
Open
Fast close slow open
Open
Fast open slow close
Open
Random strobe
Open
Random fast close slow open
Open
Random fast open slow close
Open
Burst pulse
19H