ACME RAYZOR HYBRID User manual

CONTENTS
1. Safety Instructions ......................................................................................... 2
2. Technical Specifications ................................................................................. 4
3. Control Panel ................................................................................................. 6
4. Color Wheel/Gobo Wheels ............................................................................ 7
5. How To Set The Unit....................................................................................... 7
5.1 Main Function.......................................................................................... 7
5.2 Home Position Adjustment .................................................................... 14
6. Control By Universal DMX Controller ........................................................... 16
6.1 DMX512 Connection.............................................................................. 16
6.2 Address Setting ...................................................................................... 17
6.3 DMX512 Configuration........................................................................... 17
7. Troubleshooting........................................................................................... 25
8. Fixture Cleaning........................................................................................... 25
1E

1. Safety Instructions
WARNING
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer will
not accept liability for any resulting defects or problems.
Unpack and check carefully to ensure that there is no transportation damage before using the
unit.
This product is for indoor use only. Use only in a dry location.
DO install and operate by qualified operator.
DO NOT allow children to operate the fixture.
Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.
The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces.
Be sure that no ventilation slots is blocked, otherwise the unit will be overheated.
Before operation, ensure that you are connecting this product to the proper voltage in
accordance with the specifications in this manual or on the product’s specification label.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃. Do not
operate this product at a lower or higher temperature.
DO NOT connect the device to any dimmer pack.
Keep flammable materials away from the fixture while operating to avoid fire hazard.
Make sure the power cord is not crimped or damaged; replace it immediately if damaged.
Avoid any flammable liquids, water or metal from entering the unit. Once it happens, cut off
the mains power immediately.
DO NOT operate in a dirty or dusty environment. DO clean the fixture regularly.
DO NOT touch any wire during operation as there might be a hazard of electric shock.
Please read the instruction carefully which includes important information about
the installation, usage and maintenance.
2E

Avoid entanglement of the power cord with other wires.
The minimum distance to objects/surface must be more than 2 meters.
Disconnect mains power before fuse replacement or servicing.
Replace fuse only with the same type.
In the event of serious operating problem, stop using the unit immediately.
Never turn on and off the unit time after time.
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
DO NOT open the housing as there are no user serviceable parts inside.
DO NOT attempt to operate this unit if it becomes damaged. DO NOT attempt any repairs
yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center if needed.
Disconnect this product from its power source before servicing.
DO use the original packaging if the device is to be transported.
Avoid direct eye exposure to the light source while the product is on.
DO NOT operate this product if you see damage on the housing, shields, or cables. Have the
damaged parts replaced by an authorized technician at once.
Installation:
The fixture should be fixed on the clamp. Always ensure that the unit is firmly fixed to avoid
vibration and slipping off during operation. Ensure that the trussing or area of installation must be
able to hold 10 times the weight without any deformation. Always install a safety cable that can
hold at least 12 times the weight of the fixture when installing.
DO install and operate by qualified operator. It must be installed in a place where there is out of the
reach of people.
3E

2. Technical Specifications
Power Voltage:
100-240V~, 50/60Hz
Power Consumption:
190W
Light Source:
PU55-90FWL
Angle:
Beam Angle: 2°/4°/6°/8°/10°
3°/6°/9°/12°/15°/19°(with zoom lens)
Spot Angle: Static Gobo: 10°15°(with zoom lens)
Rotating Gobo: 10°17°(with zoom lens)
Wash Angle: 15°28°
Movement:
Pan: 540°
Tilt: 270°
Pan/Tilt Resolution: 16 bit
Dimmer/Shutter:
Smooth dimming from 0-100%; outstanding strobe effect with variable speed
Color Wheel:
1 x color wheel with 8 fixed colors plus white with rainbow effect
Gobo Wheel:
1 x static gobo wheel with 7 gobos plus open
1 x rotating gobo wheel with 6 gobos plus open
Control:
DMX Channel: 17/20 Channels
Protocols: DMX, RDM, Primary/Secondary, Sound Active
Firmware Upgrade via DMX link
4E

Construction:
Display: LCD display
Data In/Out: 3-pin & 5-pin XLR
Power in/out: Power Connector in/out
Protection Rating: IP20
Features:
Motorized focus
1 x prism: 3-facets prism, rotating in both directions
Outstanding color macro effect
Independent frost effect
Integrated three features: beam, spot, and wash
Dimensions/Weight:
312x256x452mm, 13.2kgs
12.3”x10.1”x17.8”in, 29.1lbs
Photometric Diagram:
5E

3. Control Panel
1. LED:
DMX
On
DMX input present
PRIMARY
On
Primary mode
SECONDARY
On
Secondary mode
SOUND
On
Sound activation
2. DISPLAY: To show the various menus and the selected function
3. Button:
MENU
To enter into move backward or leave the menu
UP
To go backward to move up in the menu
DOWN
To go forward to move down in the menu
ENTER
To perform the desired functions
4. DMX IN:
For DMX512 link, use 3/5 -pin XLR cable to link the unit and DMX controller
5. DMX OUT:
For DMX512 link, use 3/5 -pin XLR cable to link the next units
6. MAINS IN: Used to connect to supply power
7. MAINS OUT: Used to connect to the next unit
8. FUSE(T 5A): Protect the unit from damage of over current
6E

4. Color Wheel/Gobo Wheels
DANGER!
Install the color wheel/gobo wheels with the device switched off only.
Unplug from mains before changing color wheel/gobo wheels!
CAUTION: Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be
opened!
5. How To Set The Unit
5.1 Main Function
Turn on the unit, press the MENU button into menu mode, and press the UP/DOWN button until
the required function is shown on the monitor. Select the function by the ENTER button. Use the
UP/DOWN button to choose the submenu, press the ENTER button to store and automatically
return to the last menu. Press the MENU button or let the unit idle 30 seconds to exit menu mode.
The main functions are shown below:
7E

8E

DMX Functions
To select DMX Functions, press the ENTER button to confirm, use the UP/DOWN button to select
DMX Address, DMX Channel Mode or DMX State.
DMX Address
To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to adjust the
address from 001 to 512, press the ENTER button to store. Press the MENU button back to the last
menu or let the unit idle 30 seconds to exit menu mode.
DMX Channel Mode
To select DMX Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to
select Mode1(17) or Mode2(20) channels mode, press the ENTER button to store. Press the MENU
button back to the last menu or let the unit idle 30 seconds to exit menu mode.
DMX State
To select DMX State, press the ENTER button to confirm. Use the UP/DOWN button to select
Pri./Sec.(primary/secondary mode), Blackout(fixture blacks out if DMX signal stops) or Hold(fixture
continues to obey the last command it received Via DMX if DMX signal stops), press the ENTER
button to store. Press the MENU button back to the last menu or let the unit idle 30 seconds to exit
menu mode.
Fixture Setting
To select Fixture Setting, press the ENTER button to confirm, use the UP/DOWN button to select
Pan Inverse, Tile Inverse, P/T Feedback, Dimmer Curve or Show Focus.
Pan Inverse
To select Pan Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select No
(normal) or Yes (pan inverse), press the ENTER button to store. Press the MENU button back to the
last menu or let the unit idle 30 seconds to exit menu mode.
Tilt Inverse
To select Tilt Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select No
(normal) or Yes (tilt inverse), press the ENTER button to store. Press the MENU button back to the
last menu or let the unit idle 30 seconds to exit menu mode.
9E