ACME TRACK 10 User manual

Features
E-10T/E-40T is Track Version, uniform light, sharp image edge, and
self-locking focus lens.
The product takes advantage of the heat pipe heat conduction and housing
feature to dissipate heat without fan to prolong LED life.
Specifications
Power Voltage: AC 85~127V, 50/60Hz
AC 175~264V, 50/60Hz
Power Consumption: 15W (E-10T)
30W (E-40T)
Light Source:
E-10T CW DXX: LTAW1202-012-007-5500
E-10T WW DXX: LTAW1202-012-007-3150
E-40T CW DXX: C117C1206-036-001
E-40T WW DXX: C117W1206-036-001
Color Temperature: 5600K±150K (E-10T/40T CW)
3200K±150K (E-10T/40T WW)
Beam Angle: 19°/26°/36°/50°(optional)
CRI≥95
Dimension/Weight: 273x231x128mm, 1.3kgs
10.7”x9.1”x5”in, 2.9lbs
1C

Photometric diagram:
E-10T
273
231
128
Distance(m) 2 4 6 8
36 ° 50 °
26 °
19 °
310 77 34 19
212 53 23 13
540 135 60 33
415 103 46 25
Distance(m) 6
Diameter(m) СW/WW 1.31 2.59 3.91 5.19
Diameter(m) CW/WW 1.87 3.73 5.59 7.46
1898 475 211 120
981 246 109 62
2002 501 223 125
Diameter(m) CW/WW 0.68 1.34 2.01 2.68
1095 274 122 68
Diameter(m) CW/WW 0.94 1.85 2.78 3.70
WW
2C

E-40T
How To Change The Gobo
At first, put the gobo by hand as the arrow into the gobo gel splint, and
insert the gobo gel splint into the slot of the unit, please turn the hand
knob to left or right in order to take out gobo gel splint.
Note: The diameter of the inner and outer rings of the gobo, the size and
thickness of the gobo gel splint are shown in the following figure:
Distance(m) 2 4 6 8
36 ° 50 °
26 °
19 °
Diameter(m) CW/WW 1.31 2.59 3.91 5.19
Diameter(m) CW/WW 1.87 3.73 5.59 7.46
Diameter(m) CW/WW 0.68 1.34 2.01 2.68
Diameter(m) CW/WW 0.94 1.85 2.78 3.70
1170 290 130 70
1010 250 112 62
1842 461 205 115
1950 488 215 121
2920 730 322 180
2758 680 310 170
CW
WW
596 150 66 37
517 130 56 32
3C

The Color Gel Splint Installation
At first, please push the Lock Cap button by hand as the arrow, and move
away the Lock as the arrow, then insert the color gel splint into the inside
slot from topside, and fasten the lock.
How To Change The Focus Lens
At first, please push the screws on both side of the fixture by hand as the
arrow, and move away the focus lens silently by hand as the arrow.
4C

Then insert the focus lens as the arrow silently, and insert the screws in
place by hand as the arrow, and fasten the lens.
Installation
First fix the track on the ceiling with the screws，put the dial on “OFF” of
the twist switch and rotate the tumbler switch 90 degrees clockwise.
56
Three wire Connector
Tumbler Switch
Twist Switch OFF：
Tumbler Switch:
Twist Switch
Rotae 90degreesclockwise
5C

Put the three wire connector into the track groove, the lamp body is fixed.
Then rotate the tumbler switch 90 degrees counter clockwise and make
sure the twist switch on“ON”.
After the lamp body is fixed, it can be energized.
6C

Reference Diagram for choice of connectors
Troubleshooting
The fixture does not work, no light
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
Fixture Cleansing
The cleaning of internal and external optical lenses and/or mirrors must be
carried out periodically to optimize light output. Cleaning frequency
depends on the environment in which the fixture operates: damp, smoky
or particularly dirty surrounding can cause greater accumulation of dirt on
the unit’s optics.
Clean with soft cloth and use normal glass to clean liquid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal
optics at least every 30 days.
7C

8C

9C