ACME ICARUS 620 User manual

CONTENTS
1. Safety Instructions ......................................................................................... 2
2. Technical Specifications ................................................................................. 4
3. How To Set The Unit....................................................................................... 5
3.1 Control Panel ........................................................................................... 5
3.2 Main Function.......................................................................................... 6
3.3 Home Position Adjustment .................................................................... 14
4. Control By Universal DMX Controller ........................................................... 14
4.1 DMX512 Connection.............................................................................. 14
4.2 Address Setting ...................................................................................... 15
4.3 DMX512 Configuration........................................................................... 16
5. Troubleshooting........................................................................................... 23
6. Fixture Cleaning ........................................................................................... 24
1C

1. Safety Instructions
WARNING
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer will
not accept liability for any resulting defects or problems.
Unpack and check carefully to ensure that there is no transportation damage before using the
unit.
This product is for indoor use only. Use only in a dry location.
DO install and operate by qualified operator.
DO NOT allow children to operate the fixture.
Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.
The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces.
Be sure that no ventilation slots is blocked, otherwise the unit will be overheated.
Before operation, ensure that you are connecting this product to the proper voltage in
accordance with the specifications in this manual or on the product’s specification label.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.Do not
operate this product at a lower or higher temperature.
DO NOT connect the device to any dimmer pack.
Keep flammable materials away from the fixture while operating to avoid fire hazard.
Make sure the power cord is not crimped or damaged; replace it immediately if damaged.
Unit’s surface temperature may reach up to 75℃. DO NOT touch the housing bare-handed
during its operation.
Avoid any flammable liquids, water or metal from entering the unit. Once it happens, cut off
the mains power immediately.
Please read the instruction carefully which includes important information
about the installation, usage and maintenance.
2C

DO NOT operate in a dirty or dusty environment. DO clean the fixture regularly.
DO NOT touch any wire during operation as there might be a hazard of electric shock.
Avoid entanglement of the power cord with other wires.
The minimum distance to objects/surface must be more than 1.5 meters.
Disconnect mains power before fuse replacement or servicing.
Replace fuse only with the same type.
In the event of serious operating problem, stop using the unit immediately.
Never turn on and off the unit time after time.
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
DO NOT open the housing as there are no user serviceable parts inside.
DO NOT attempt to operate this unit if it becomes damaged. DO NOT attempt any repairs
yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center if needed.
Disconnect this product from its power source before servicing.
DO use the original packaging if the device is to be transported.
Avoid direct eye exposure to the light source while the product is on.
DO NOT operate this product if you see damage on the housing, shields, or cables. Have the
damaged parts replaced by an authorized technician at once.
Installation:
The fixture should be fixed on the clamp. Always ensure that the unit is firmly fixed to avoid
vibration and slipping off during operation. Ensure that the trussing or area of installation must be
able to hold 10 times the weight without any deformation. Always install a safety cable that can
hold at least 12 times the weight of the fixture when installing.
DO install and operate by qualified operator. It must be installed in a place where there is out of the
reach of people.
3C

2. Technical Specifications
Power Voltage:
100-240V~ 50/60Hz
Power Consumption:
610W
Light Source:
37x20W RGBW LED
Zoom Range:
10°~60°
Movement:
Pan: 540°
Tilt: 270°
Pan/Tilt Resolution: 16bit
Dimming/Strobe:
0~100% smooth dimming, variable strobe speeds
Control:
DMX Channel: 14/26/15 Channels
Control Mode: DMX512, RDM
Firmware Upgrade: Update via DMX link
Construction:
Display: LCD display
Data In/Out: 3-pin & 5-pin XLR
Power In/Out: Power Connector in/out
Protection Rating: IP20
Features:
Electronic linear zoom system
Ring control, outstanding color macro effect
4C

Dimension/Weight:
430x246x512mm, 19.5kgs
17"x9.7"x20"in, 42.9lbs
Photometric Diagram:
3. How To Set The Unit
3.1 Control Panel
1. Display: To show the various menus and the selected functions
2. LED:
POWER
ON
Power on
DMX
ON
DMX input present
5C

3. Button:
MENU
To enter into move backward or leave the menu
DOWN
To go forward in the selected functions
UP
To go backward in the selected functions
ENTER
To confirm the selected functions
4. DMX IN:
For DMX512 link, use 3/5 -pin XLR cable to link the unit and the DMX controller
5. DMX OUT:
For DMX512 link, use 3/5-pin XLR cable to link the next units
6. POWERCON IN:
To connect to supply power
7. POWERCON OUT:
To connect to the next fixture
8. FUSE(T 10A):
Protects the unit from damage of over-voltage or short circuit
3.2 Main Function
Turn on the unit, press the MENU button into menu mode, and press the UP/DOWN button until
the required function is shown on the monitor. Select the function by pressing the ENTER button.
Use the UP/DOWN button to choose the submenu, press the ENTER button to store and
automatically return to the last menu. Press the MENU button or let the unit idle 30 seconds to exit
menu mode.
The main functions are shown below:
6C

7C

DMX Functions
To select DMX Functions, press the ENTER button to confirm, use the UP/DOWN button to select
DMX Address, DMX Channel Mode or View DMX Value.
DMX Address
To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to adjust the
address from 001 to 499/487/498, press the ENTER button to setup. Press the MENU button back to
the last menu or let the unit idle 30 seconds to exit menu mode.
DMX Channel Mode
To select DMX Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to
select Mode1 (14), Mode2 (26) or Mode3 (15), press the ENTER button to setup. Press the MENU
button back to the last menu or let the unit idle 30 seconds to exit menu mode.
View DMX Value
To select View DMX Value, press the ENTER button to confirm. Use the UP/DOWN button to view
the DMX channel values. Press the MENU button back to the last menu or let the unit idle 30
seconds to exit menu mode.
Fixture Setting
To select Fixture Setting, press the ENTER button to confirm, use the UP/DOWN button to select
Pan Inverse, Tilt Inverse, P/T Feedback,BL.O. P/T Moving, White Balance, Cooling Mode,Dimmer
Curve or Dimmer Speed.
Pan Inverse
To select Pan Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select No
(normal) or Yes (pan inverse), press the ENTER button to setup. Press the MENU button back to the
last menu or let the unit idle 30 seconds to exit menu mode.
Tilt Inverse
To select Tilt Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select No
(normal) or Yes (tilt inverse), press the ENTER button to setup. Press the MENU button back to the
last menu or let the unit idle 30 seconds to exit menu mode.
8C

P/T Feedback
To select P/T Feedback, press the ENTER button to confirm. Use the UP/DOWN button to select No
(Pan or tilt’s position will not feedback while out of step) or Yes (Feedback while pan/tilt out of step),
press the ENTER button to setup. Press the MENU button back to the last menu or let the unit idle
30 seconds to exit menu mode.
BL.O. P/T Moving
To select BL.O. P/T Moving, press the ENTER button to confirm. Use the UP/DOWN button to select
No (normal while pan/tilt moving) or Yes (blackout while pan/tilt moving), press the ENTER button
to setup. Press the MENU button back to the last menu or let the unit idle 30 seconds to exit menu
mode.
White Balance
To select White Balance, press the ENTER button to confirm. Use the UP/DOWN button to select
Red, Green or Blue. Once selected, press the ENTER button to confirm, and use the UP/DOWN
button to adjust the value from 125 to 255, press the ENTER button to setup. Press the MENU
button back to the last menu or let the unit idle 30 seconds to exit menu mode.
Cooling Mode
To select Cooling Mode, press the ENTER button to confirm. Use the UP/DOWN button to select
Auto or Silent. Once selected, press the ENTER button to setup. Press the MENU button back to the
last menu or let the unit idle 30 seconds to exit menu mode.
Dimmer Curve
To select Dimmer Curve, press the ENTER button to confirm. Use the UP/DOWN button to select
Linear, Square Law, Inverse Squ. or S-Curve. Once selected, press the ENTER button to store. Press
the MENU button back to the last menu or let the unit idle 30 seconds to exit menu mode.
Linear: The increase in light intensity appears to be linear as DMX value is increased.
Square Law: Light intensity control is finer at low levels and coarser at high levels.
Inverse Square Law: Light intensity control is coarser at low levels and finger at high levels.
S-Curve: Light intensity control is finger at low levels and high levels and coarser at medium levels.
9C