Amazone Cayena 6001 User manual
Operating Manual
az
Cayena 6001
Cayena 6001-C
MG4235
BAH0062-4 09.15
Please read this operating manual before
commissioning.
Keep it in a safe place for future use!
en
2 Cayena BAH0062-4 09.15
Reading the instruction
manual and to adhere to it should not appear to
be inconvenient and superfluous as it is not
enough to hear from others and to realise that a
machine is good, to buy it and to believe that now
everything would work by itself. The person
concerned would not only harm himself but also
make the mistake of blaming the machine for the
reason of a possible failure instead of himself. In
order to ensure a good success one should go into
the mind of a thing or make himself familiar with
every part of the machine and to get acquainte
d
with its handling. Only this way, you would be
satisfied both with the machine as also with
yourself. To achieve this is the purpose of this
instruction manual.
Leipzig-Plagwitz 1872.
Cayena BAH0062-4 09.15 3
Identification data
Please insert the identification data of the implement. The identification data
are arranged on the type plate.
Implement ID no.: (ten digits)
Type:
Basic weight (kg):
Permissible total weight (kg):
Year of manufacture:
Manufacturer's address
AMAZONEN-WERKE
H. DREYER GmbH & Co. KG
Postfach 51
D-49202
Tel.:
Fax:
E-mail:
Hasbergen, Germany
+ 49 (0) 5405 501-0
+ 49 (0) 5405 501-234
Spare part orders
Spare parts lists are freely accessible in the spare parts portal at
www.amazone.de.
Please send orders to your AMAZONE dealer.
Formalities of the operating manual
Type: Cayena
Document number: MG4235
Compilation date: 09.15
Copyright AMAZONEN-WERKE H. DREYER GmbH & Co. KG, 2015
All rights reserved.
Reprinting, even of sections, only possible with the approval of
AMAZONEN-WERKE H. DREYER GmbH & Co. KG.
4 Cayena BAH0062-4 09.15
Foreword
Dear Customer,
You have chosen one of the quality products from the wide product
range of AMAZONEN-WERKE, H. DREYER GmbH & Co. KG. We
thank you for your trust in our products.
On receiving the implement, check to see if it has been damaged
during transport or if parts are missing. Using the delivery note, check
that the implement has been delivered in full, including any special
equipment ordered. Damage can only be rectified if problems are
signalled immediately.
Before commissioning, read and understand this operating manual,
and particularly the safety information. Only after careful reading will
you be able to benefit from the full scope of your newly purchased
implement.
Please ensure that all the implement operators have read this
operating manual before they put the implement into operation.
Should you have any questions or problems, please consult this
operating manual or contact your local service partner.
Regular maintenance and timely replacement of worn or damaged
parts increases the lifespan of your implement.
Cayena BAH0062-4 09.15 5
1User information........................................................................................10
1.1Purpose of the document.......................................................................................................10
1.2Locations in the operating manual.........................................................................................10
1.3Diagrams................................................................................................................................10
2General Safety Instructions ......................................................................11
2.1Obligations and liability..........................................................................................................11
2.2Representation of safety symbols..........................................................................................13
2.3Organisational measures.......................................................................................................14
2.4Safety and protective equipment...........................................................................................14
2.5Informal safety measures.......................................................................................................14
2.6User training...........................................................................................................................15
2.7Safety measures in normal operation....................................................................................16
2.8Danger from residual energy .................................................................................................16
2.9Maintenance and repair work, fault elimination .....................................................................16
2.10Design changes .....................................................................................................................17
2.10.1Spare and wear parts and aids..............................................................................................18
2.11Cleaning and disposal............................................................................................................18
2.12User workstation....................................................................................................................18
2.13Warning symbols and other labels on the implement............................................................19
2.13.1Positions of warning symbols and other labels......................................................................26
2.14Dangers if the safety information is not observed..................................................................28
2.15Safety-conscious working......................................................................................................28
2.16Safety information for users...................................................................................................29
2.16.1General safety instructions and accident prevention instructions..........................................29
2.16.2Hydraulic system....................................................................................................................33
2.16.3Electrical system....................................................................................................................34
2.16.4Attached implements .............................................................................................................34
2.16.5Brake system .........................................................................................................................35
2.16.6Tyres......................................................................................................................................36
2.16.7Operation of the seed drill......................................................................................................36
2.16.8PTO shaft operation...............................................................................................................37
2.16.9Cleaning, maintenance and repair.........................................................................................37
3Loading and unloading road transport vehicles.....................................38
3.1Loading the implement...........................................................................................................39
3.2Unloading the implement.......................................................................................................40
4Product description...................................................................................41
4.1Overview of assembly groups................................................................................................42
4.2Safety and protective equipment...........................................................................................45
4.3Overview – Supply lines between the tractor and the implement..........................................46
4.4Transportation equipment......................................................................................................48
4.5Intended use ..........................................................................................................................50
4.6Danger areas and danger points ...........................................................................................51
4.7Rating plate and CE mark......................................................................................................52
4.8Technical data........................................................................................................................53
4.9Necessary tractor equipment.................................................................................................55
4.10Noise production data............................................................................................................55
5Layout and function...................................................................................56
5.1Service brake system.............................................................................................................57
5.1.1Parking brake.........................................................................................................................57
5.1.2Dual-circuit pneumatic service brake system ........................................................................58
5.1.3Hydraulic service brake system.............................................................................................58
6 Cayena BAH0062-4 09.15
5.1.4Implements without independent service brake system ....................................................... 58
5.2Accessories kit with the operating manual............................................................................ 59
5.3Radar..................................................................................................................................... 59
5.4AMATRON 3 control terminal................................................................................................ 60
5.5AMADRILL+ control terminal................................................................................................. 61
5.6Frame and implement booms ............................................................................................... 62
5.7Hopper................................................................................................................................... 63
5.7.1Fill level monitoring................................................................................................................ 65
5.8Metering ................................................................................................................................ 66
5.8.1one-chamber system dosing................................................................................................. 67
5.8.2Two-chamber system dosing................................................................................................ 68
5.8.3Application rate/Calibration test ............................................................................................ 69
5.8.4Seed pre-metering (only with AMATRON 3 control terminal)............................................... 71
5.8.5Metering rollers...................................................................................................................... 72
5.8.5.1Metering roller diagram table ................................................................................................ 73
5.8.5.2Table – metering rollers, seed............................................................................................... 75
5.8.5.3Table – metering rollers, fertiliser.......................................................................................... 75
5.9Blower fan ............................................................................................................................. 76
5.9.1Connecting the blower fan to the tractor hydraulics.............................................................. 76
5.9.2Blower fan connection to the tractor PTO shaft (on-board hydraulic system) ...................... 77
5.9.3Blower fan speed table for implements with one hopper chamber....................................... 78
5.9.4Blower fan speed for implements with two hopper chambers .............................................. 79
5.10Distributor head..................................................................................................................... 80
5.10.1Seed tube monitoring (optional)............................................................................................ 80
5.11Coulter chisel and seed/fertiliser placement depth............................................................... 81
5.12Leading roller feelers (optional)............................................................................................. 82
5.13Cutting discs (optional).......................................................................................................... 83
5.14Wedge ring tyres................................................................................................................... 84
5.14.1Furrow ridge levellers (optional)............................................................................................ 84
5.15Exact following harrow .......................................................................................................... 85
5.16Rear harrow (optional) .......................................................................................................... 86
5.17Tractor wheel mark eradicator (option)................................................................................. 86
5.18Track markers (optional) ....................................................................................................... 87
5.19Tramlines............................................................................................................................... 88
5.19.1Examples for creating tramlines............................................................................................ 90
5.19.2Tramline rhythm 4, 6 and 8................................................................................................... 92
5.19.3Tramline control 2 and 21 ..................................................................................................... 93
5.19.4One-sided switching.............................................................................................................. 94
5.19.5Tramline marker (optional).................................................................................................... 94
6Commissioning ......................................................................................... 95
6.1Checking the suitability of the tractor.................................................................................... 96
6.1.1Calculating the actual values for the total tractor weight, tractor axle loads and load
capacities, as well as the minimum ballast ........................................................................... 97
6.1.1.1Data required for the calculation (hitched implement) .......................................................... 98
6.1.1.2Calculation of the required minimum ballasting at the front GV min of the tractor for
assurance of the steering capability...................................................................................... 99
6.1.1.3Calculation of the actual front axle load of the tractor TV tat................................................... 99
6.1.1.4Calculation of the actual total weight of the combined tractor and implement...................... 99
6.1.1.5Calculation of the actual rear axle load of the tractor TH tat ................................................... 99
6.1.1.6Tractor tyre load capacity...................................................................................................... 99
6.1.1.7Table ................................................................................................................................... 100
6.1.2Requirements for tractor operation with attached implements ........................................... 101
6.2Securing the tractor/implement against unintentional start-up and rolling.......................... 102
6.3Installation regulations for the hydraulic fan drive connection ............................................ 103
7Coupling and uncoupling the implement.............................................. 104
7.1Dual-circuit pneumatic service brake system...................................................................... 106
Cayena BAH0062-4 09.15 7
7.1.1Coupling the brake and supply lines....................................................................................108
7.1.2Uncoupling the supply and brake line..................................................................................110
7.1.3Control element of the dual-circuit pneumatic service braking system ...............................111
7.2Hydraulic service brake system...........................................................................................112
7.2.1Coupling the hydraulic service brake system ......................................................................113
7.2.2Uncoupling the hydraulic service brake system...................................................................115
7.3Hydraulic hose lines.............................................................................................................117
7.3.1Coupling the hydraulic hose lines........................................................................................117
7.3.2Uncoupling the hydraulic hose lines ....................................................................................118
7.4Coupling the implement to the tractor..................................................................................119
7.5Uncoupling the implement ...................................................................................................124
7.6Connect/disconnect the PTO shaft driven hydraulic pump..................................................127
7.6.1Connecting the hydraulic pump ...........................................................................................127
7.6.2Uncoupling the hydraulic pump............................................................................................128
8Settings.....................................................................................................129
8.1Setting the working depth of the cutting discs .....................................................................130
8.2Repositioning the fill level sensor ........................................................................................131
8.3Installing/removing the metering roller.................................................................................131
8.4Setting the spread rate with a calibration test......................................................................135
8.5Setting the blower fan speed ...............................................................................................137
8.5.1Setting the blower fan speed via the flow control valve of the tractor..................................138
8.5.2Setting the blower fan speed on tractors without flow control valve....................................138
8.5.3Set the blower fan speed when connecting the hydraulic motor to the tractor PTO
shaft .....................................................................................................................................138
8.5.4Pressure relief valve with round outer contour ....................................................................139
8.5.4.1Basic setting of the pressure relief valve.............................................................................139
8.5.4.2Blower fan speed setting......................................................................................................139
8.5.5Pressure relief valve with hexagonal outer contour.............................................................140
8.5.5.1Basic setting of the pressure relief valve.............................................................................140
8.5.5.2Blower fan speed setting......................................................................................................140
8.6Adjusting the seed placement depth....................................................................................141
8.7Exact following harrow.........................................................................................................142
8.7.1Exact following harrow tine position.....................................................................................142
8.7.2Exact following harrow pressure adjustment.......................................................................142
8.8Adjusting the rear harrow.....................................................................................................143
8.9Adjusting the tractor wheel mark eradicator (on the field)...................................................143
8.10Track markers......................................................................................................................144
8.11One-sided switching.............................................................................................................145
8.11.1Half-sided switching off........................................................................................................145
8.12Moving the tramline marker to the working/transport position.............................................146
8.12.1Move the tramline marker to working position.....................................................................146
8.12.2Move the tramline markers to the transport position............................................................146
8.13Moving the transport safety bar into transport/parking position...........................................147
8.13.1Moving the transport safety bar to transport position ..........................................................147
8.14Moving the road safety bar into parking position.................................................................148
9Transportation .........................................................................................149
9.1Set the implement to road transport mode ..........................................................................149
9.2Legal regulations and safety................................................................................................150
10Use of the implement...............................................................................154
10.1Work commencement..........................................................................................................156
10.2Unfolding/folding the implement boom ................................................................................157
10.2.1Unfolding the implement booms ..........................................................................................157
10.2.2Folding the implement booms..............................................................................................160
10.3Filling the hopper .................................................................................................................162
10.3.1Opening/closing tarpaulin ....................................................................................................163
8 Cayena BAH0062-4 09.15
10.3.2Opening the hopper cover................................................................................................... 164
10.3.3Close the hopper cover....................................................................................................... 165
10.4During the work................................................................................................................... 166
10.4.1Overview of checks............................................................................................................. 166
10.4.2Checking the placement depth of the seed......................................................................... 167
10.4.3Turning at end of the field ...................................................................................................167
10.5End of work in the field........................................................................................................ 168
10.5.1Emptying the hopper and/or the metering unit.................................................................... 169
11Faults........................................................................................................ 170
11.1Residual seed volume indicator.......................................................................................... 170
11.2Deviations between the preset and actual seeding rates ................................................... 171
11.3Fault table............................................................................................................................ 172
12Cleaning, maintenance and repair......................................................... 173
12.1Fuse .................................................................................................................................... 173
12.1.1Securing the connected implement..................................................................................... 174
12.1.2Securing the lifted implement.............................................................................................. 174
12.2Cleaning the implement ...................................................................................................... 175
12.2.1Clean the oil cooler.............................................................................................................. 176
12.2.2Clean the distributor head................................................................................................... 177
12.3Setting and repair work (specialist workshop) .................................................................... 178
12.3.1Drawbar pipe length adjustment (specialist workshop)....................................................... 178
12.3.2Adjusting the tramline track width of the cultivating tractor (specialist workshop).............. 179
12.3.3Adjusting the tramline track width of the cultivating tractor (specialist workshop).............. 180
12.3.4Repairs to the pressure tank (workshop)............................................................................ 182
12.4Lubrication........................................................................................................................... 183
12.4.1Lubrication points – overview.............................................................................................. 184
12.5Maintenance schedule – overview...................................................................................... 186
12.5.1Visual inspection of the draw rail......................................................................................... 188
12.5.2Checking the tyre inflation pressure of the leading roller feelers (optional)........................ 188
12.5.3Checking the tightening torques of the wheel and hub screws (specialist workshop)........ 188
12.5.4Check the inflation pressure of the wedge ring tyres.......................................................... 189
12.5.5On-board hydraulics – Oil check and oil filter change......................................................... 190
12.5.6Inspection criteria for hydraulic hose lines before every start-up........................................ 192
12.5.7Inspection criteria for hydraulic hose lines using the maintenance schedule..................... 192
12.5.7.1Identification of hydraulic hose lines ................................................................................... 193
12.5.7.2Installing and removing hydraulic hose lines ...................................................................... 194
12.5.8Service brake system (all variants)..................................................................................... 195
12.5.8.1General visual inspection of the service brake system....................................................... 195
12.5.8.2Checking the service brake system for safe operating condition (specialist workshop)..... 195
12.5.9Service brake system (Dual-circuit pneumatic service brake system)................................ 196
12.5.9.1Exterior inspection of the compressed air tank................................................................... 196
12.5.9.2Checking the pressure in the compressed air tank (specialist workshop).......................... 196
12.5.9.3Leak tightness check (specialist workshop)........................................................................ 197
12.5.9.4Cleaning the line filters (specialist workshop)..................................................................... 197
12.5.10Setting the track marker for correct threading into the transport bracket........................... 198
12.6Screw tightening torques..................................................................................................... 199
13Hydraulic diagram................................................................................... 200
13.1Hydraulic diagram Cayena 6001 with AMADRILL+............................................................ 200
13.2Hydraulic diagram – Cayena 6001(-C) with AMATRON 3.................................................. 202
Cayena BAH0062-4 09.15 9
User information
10 Cayena BAH0062-4 09.15
1 User information
The User Information section provides information on use of the
operating manual.
1.1 Purpose of the document
This operating manual
describes the operation and maintenance of the implement.
provides important information on safe and efficient handling of
the implement.
is an integral part of the implement and should always be kept
with the implement or the towing vehicle.
must be kept in a safe place for future use.
1.2 Locations in the operating manual
A
ll the directions specified in the operating manual are always seen in
the direction of travel.
1.3 Diagrams
Instructions and responses
Activities to be carried out by the user are given as numbered
instructions. Always keep to the order of the instructions. The reaction
to the handling instructions is given by an arrow. Example:
1. Instruction 1
Reaction of the implement to handling instruction 1
2. Instruction 2
Lists
Lists without an essential order are shown as a list with bullets.
Example:
Point 1
Point 2
Item numbers in diagrams
Numbers in round brackets refer to the item numbers in the diagrams.
The first number refers to the diagram and the second number to the
item.
Example (Fig. 3/6): Figure 3
Position 6
General Safety Instructions
Cayena BAH0062-4 09.15 11
2 General Safety Instructions
This section contains important information on safe operation of the
implement.
2.1 Obligations and liability
Comply with the instructions in the operating manual
Knowledge of the basic safety information and safety regulations is a
basic requirement for safe handling and fault-free implement
operation.
Obligations of the operator
The operator is obliged only to let those people work with/on the
implement who
are aware of the basic workplace safety information and accident
prevention regulations.
have been trained in working with/on the implement.
have read and understood this operating manual.
The operator is obliged
to keep all the warning symbols on the implement in a legible
state.
to replace damaged warning symbols.
Obligations of the user
Before starting work, anyone charged with working with/on the
implement is obliged
to comply with the basic workplace safety instructions and
accident prevention regulations.
to read and understand the "General safety information" section
of this operating manual.
to read the section "Warning symbols and other labels on the
implement" in this operating manual and to follow the safety
instructions represented by the warning symbols when operating
the implement.
to get to know the implement.
to read the sections of this operating manual, important for
carrying out your work.
If the user discovers that a function is not working properly, then they
must eliminate this fault immediately. If this is not the task of the user
or if the user does not possess the appropriate technical knowledge,
then they should report this fault to their superior (operator).
General Safety Instructions
12 Cayena BAH0062-4 09.15
Risks in handling the implement
The implement has been constructed to the state-of-the art and the
recognised rules of safety. However, operating the implement may
cause risks and restrictions to
the health and safety of the user or third persons.
the implement itself.
other property.
Only use the implement
for the purpose for which it was intended.
in a perfect state of repair.
Eliminate any faults immediately which could impair safety.
Guarantee and liability
Our "General conditions of sales and delivery" are always applicable.
These shall be available to the operator, at the latest on conclusion of
the contract. Guarantee and liability claims for damage to people or
property will be excluded if they can be traced back to one or more of
the following causes:
Improper use of the implement
Improper installation, commissioning, operation and
maintenance of the implement
Operation of the implement with defective safety equipment or
improperly attached or non-functioning safety and protective
equipment
Non-compliance with the instructions in the operating manual
regarding commissioning, operation and maintenance
Unauthorised design changes to the implement
Insufficient monitoring of implement parts which are subject to
wear
Improperly executed repairs
Disasters due to the effects of foreign objects and force majeure
General Safety Instructions
Cayena BAH0062-4 09.15 13
2.2 Representation of safety symbols
Safety instructions are indicated by the triangular safety symbol and
the highlighted signal word. The signal word (DANGER, WARNING,
CAUTION) describes the severity of the risk, and carries the following
meaning:
DANGER
Indicates a direct threat at high risk which will result in death or
most serious bodily harm (loss of limbs or long-term harm),
should it not be prevented.
If the instructions are not followed, then this will result in
immediate death or serious physical injury.
WARNING
Indicates a medium risk, which could result in death or (serious)
physical injury if not avoided.
If the instructions are not followed, then this may result in death
or serious physical injury.
CAUTION
Indicates a low risk which could cause minor or medium level
physical injury or damage to property if not avoided.
IMPORTANT
Indicates an obligation to special behaviour or an activity required for
proper implement handling.
Non-compliance with these instructions can cause faults on the
implement or disturbance to the environment.
NOTE
Indicates handling tips and particularly useful information.
These instructions will help you to use all the functions of your
implement in the best way possible.
General Safety Instructions
14 Cayena BAH0062-4 09.15
2.3 Organisational measures
The operator must provide the necessary personal protective
equipment as per the information provided by the manufacturer of the
crop protection agent to be used, such as:
Safety glasses
Protective shoes
Chemical-resistant overalls
Skin protection agents, etc.
The operation manual
must always be kept at the place at which the implement is
operated.
must always be easily accessible for the user and maintenance
personnel.
Check all the available safety equipment regularly.
2.4 Safety and protective equipment
Before starting up the implement each time, all the safety and
protection equipment must be properly attached and fully functional.
Check all safety and protection equipment regularly.
Faulty safety equipment
Faulty or disassembled safety and protection equipment can lead to
dangerous situations.
2.5 Informal safety measures
As well as all the safety information in this operating manual, comply
with the general, national regulations pertaining to accident prevention
and environmental protection.
When driving on public roads and routes you should comply with the
statutory road traffic regulations.
General Safety Instructions
Cayena BAH0062-4 09.15 15
2.6 User training
Only those people who have been trained and instructed may work
with/on the implement. The operator must clearly specify the
responsibilities of the people charged with operation and
maintenance work.
People being trained may only work with/on the implement under the
supervision of an experienced person.
Person
Activity
Person
specially trained
for the activity 1)
Trained
person 2)
Person with specialist
training (specialist
workshop) 3)
Loading/Transport X X X
Commissioning X
Set-up, tool installation X
Operation X
Maintenance X
Troubleshooting and fault
elimination X X
Disposal X
Legend: X..permitted
..not permitted
1) A person who can assume a specific task and who can carry out this task for an appropriately
qualified company.
2) Instructed persons are those who have been instructed in their assigned tasks and in the
possible risks in the case of improper behaviour, have been trained if necessary, and have been
informed about the necessary protective equipment and measures.
3) People with specialist technical training shall be considered as a specialist. Due to their specialist
training and their knowledge of the appropriate regulations, they can evaluate the work with
which they have been charged and detect possible dangers.
Comment:
A qualification equivalent to specialist training can be obtained from several years' experience in
the relevant field.
Only a specialist workshop may carry out maintenance and repair
work on the implement, if such work is additionally marked
"Specialist workshop". The personnel of a specialist workshop shall
possess the appropriate knowledge and suitable aids (tools, lifting
and support equipment) for carrying out the maintenance and repair
work on the implement in a way which is both appropriate and safe.
General Safety Instructions
16 Cayena BAH0062-4 09.15
2.7 Safety measures in normal operation
Only operate the implement if all the safety and protection equipment
is fully functional.
Check the implement at least once a day for visible damage and
check the function of the safety and protection equipment.
2.8 Danger from residual energy
Note that there may be residual mechanical, hydraulic, pneumatic and
electrical/electronic energy on the implement.
Use appropriate measures to inform the operating personnel. You can
find detailed information in the relevant sections of this operating
manual.
2.9 Maintenance and repair work, fault elimination
Carry out prescribed setting, maintenance and inspection work in
good time.
Secure all media such as compressed air and the hydraulic system
against unintentional start-up.
Carefully fix and secure larger assemblies to lifting gear when
carrying out replacement work.
Check all the bolted connections for tightness. On completion of the
maintenance work, check the function of the safety and protective
devices.
General Safety Instructions
Cayena BAH0062-4 09.15 17
2.10 Design changes
You may make no changes, expansions or modifications to the
implement without the authorisation of AMAZONEN-WERKE. This
also applies when welding support parts.
Any expansion or modification work shall require the written approval
of AMAZONEN-WERKE. Only use modification and accessory parts
approved by AMAZONEN-WERKE so that the type approval, for
example, remains valid in accordance with national and international
regulations.
Vehicles with an official type approval or with equipment connected to
a vehicle with a valid type approval or approval for road transport
according to the German road traffic regulations must be in the state
specified by the approval.
WARNING
Risk of crushing, cutting, being trapped or drawn in, or impact
through the failure of support parts.
It is strictly forbidden to
drill holes in the frame or on the running gear.
increase the size of existing holes on the frame or the running gear.
weld support parts.
General Safety Instructions
18 Cayena BAH0062-4 09.15
2.10.1 Spare and wear parts and aids
Immediately replace any implement parts which are not in a perfect
state.
Use only genuine AMAZONE spare and wear parts or the parts
cleared by AMAZONEN-WERKE so that the operating permit retains
its validity in accordance with national and international regulations. If
you use wear and spare parts from third parties, there is no guarantee
that they have been designed and manufactured in such a way as to
meet the requirements placed on them.
AMAZONEN-WERKE shall accept no liability for damage caused by
the use of non-approved spare and wear parts or aids.
2.11 Cleaning and disposal
Handle and dispose of any materials used carefully, in particular
when carrying out work on lubrication systems and equipment
and
when cleaning using solvents.
2.12 User workstation
The implement may be operated by only one person sitting in the
driver's seat of the tractor.
General Safety Instructions
Cayena BAH0062-4 09.15 19
2.13 Warning symbols and other labels on the implement
Always keep all the warning symbols of the implement clean and in a
legible state. Replace illegible warning symbols. You can obtain the
warning symbols from your dealer using the order number (e.g.,
MD 075).
Warning symbols – structure
Warning symbols indicate danger areas on the implement and warn
against residual dangers. At these points, there are permanent or
unexpected dangers.
A warning symbol consists of two fields:
Field 1
is a symbol describing the danger, surrounded by triangular safety
symbol.
Field 2
is a symbol showing how to avoid the danger.
Warning symbols – explanation
The column Order number and explanation provides an explanation
of the adjacent warning symbol. The description of the warning
symbols is always the same and specifies, in the following order:
1. A description of the danger.
For example: risk of cutting
2. The consequence of non-compliance with the risk avoidance
instructions.
For example: causes serious injuries to fingers or hands.
3. Risk avoidance instructions.
For example: only touch implement parts when they have come
to a complete standstill.
General Safety Instructions
20 Cayena BAH0062-4 09.15
Order number and explanation Warning symbols
MD 076
Risk of drawing-in/entrapment for hand or
arm due to moving force-transmission parts!
This hazard can cause the most severe injuries
with loss of body parts.
Never open or remove protective equipment,
while the tractor engine is running with the
universal joint shaft or hydraulic/electronic
system connected.
if the ground wheel drive is moving.
MD 078
Risk of crushing of fingers/hand by
accessible, moving parts of the implement!
This hazard can cause the most severe injuries
with loss of body parts.
Never reach into the danger area when the
tractor engine is running with the universal joint
shaft or hydraulic/electrical system connected.
MD 082
Risk of falling when riding the implement on
treads or platforms!
Causes serious, potentially fatal injuries
anywhere on the body.
It is forbidden to ride on the implement or climb
the implement when it is running. This prohibition
also applies to implements with step surfaces or
platforms.
Make sure that nobody is riding on the
implement.
Other manuals for Cayena 6001
1
This manual suits for next models
1
Table of contents
Other Amazone Farm Equipment manuals
Amazone
Amazone DMC Primera 3000 User manual
Amazone
Amazone Catros 2503 Special Installation instructions
Amazone
Amazone Cataya 3000 Special User manual
Amazone
Amazone Cayros Series User manual
Amazone
Amazone Pantera 4503 User manual
Amazone
Amazone UX 7601 Super User manual
Amazone
Amazone Cataya User manual
Amazone
Amazone DMC Primera 12001-2C User manual
Amazone
Amazone ZA-X Perfect 02 User manual
Amazone
Amazone T-Pack U 1450-880 User manual
Amazone
Amazone KE 3002 Installation instructions
Amazone
Amazone UX 11201 Super User manual
Amazone
Amazone Citan 12001-C User manual
Amazone
Amazone Certos 4001-2TX User manual
Amazone
Amazone Catros XL 7003-2TX User manual
Amazone
Amazone Ceus 3000-TX Installation instructions
Amazone
Amazone DMC Primera 9001-2C User manual
Amazone
Amazone ZA-M 3001 User manual
Amazone
Amazone Cenius 4002-2T Super User manual
Amazone
Amazone Precea 9000-TCC Installation instructions
