Amazone AD-P 3001 Special 850 User manual
Operating manual
az
Pneumatic pack top seed drill
AD-P 3001/3501/4001 Special 850
AD-P 3001/3501/4001 Special 1250
MG6093
BAH0095-3 06.20
Please read and observe this
operating manual before initial
operation of the implement!
Keep it in a safe place for future use!
en
AD-P 30/35/4001 SPECIAL BAH0095-3 06.20 3
Identification data
Please insert the identification data of the implement. The identifica-
tion data are arranged on the rating plate.
Machine type:
Implement number, ten digits:
Year of manufacture:
Permissible total weight [kg]:
Manufacturer address
AMAZONEN-WERKE
H. DREYER GmbH & Co. KG
Postfach 51
D-49202 Hasbergen
Tel.: 49 (0) 5405 501-0
E-mail: [email protected]
Spare Parts Order
Spare parts lists are freely accessible in the spare parts portal at
www.amazone.de.
Please send orders to your AMAZONE dealer.
Formalities of the operating manual
Machine type: AD-P 30/35/4001 SPECIAL
Document number: MG6093
Compilation date: 06.20
Copyright AMAZONEN-WERKE H. DREYER GmbH & Co. KG, 2020
All rights reserved.
Reprinting, even of sections, permitted only with the approval of
AMAZONEN-WERKE H. DREYER GmbH & Co. KG.
4 AD-P 30/35/4001 SPECIAL BAH0095-3 06.20
Foreword
Dear Customer,
You have chosen one of the quality products from the wide product range of AMAZONEN-WERKE,
H. DREYER GmbH & Co. KG. We thank you for your trust in our products.
On receiving the implement, check to see if it has been damaged during transport or if parts are miss-
ing. Check the delivered implement for completeness based on the delivery slip, including the ordered
special equipment. Damage can only be rectified if problems are claimed immediately.
Before initial operation, read and comply with the information in this operating manual, and particularly
the safety instructions. Only after careful reading will you be able to benefit from the full scope of your
newly purchased implement.
Please ensure that all the implement operators have read this operating manual before they put the
implement into operation.
If there are any questions or problems, please read this operating manual or contact your local service
partner.
Regular maintenance and timely replacement of worn or damaged parts increases the service life of
your implement.
AD-P 30/35/4001 SPECIAL BAH0095-3 06.20 5
1User information ........................................................................................ 10
2General Safety Information ....................................................................... 11
2.1Obligations and liability .......................................................................................................... 11
2.2Representation of safety symbols .......................................................................................... 13
2.3Organisational measures ....................................................................................................... 14
2.4Safety and protective equipment ........................................................................................... 14
2.5Informal safety measures ....................................................................................................... 14
2.6User training ........................................................................................................................... 15
2.7Safety measures in normal operation .................................................................................... 16
2.8Danger from residual energy ................................................................................................. 16
2.9Maintenance and repair work, fault elimination ..................................................................... 16
2.10Design changes ..................................................................................................................... 16
2.10.1Spare and wear parts and aids .............................................................................................. 17
2.11Cleaning and disposal ............................................................................................................ 17
2.12Workstation of the operator .................................................................................................... 17
2.13Warning symbols on the implement ....................................................................................... 18
2.13.1Position of warning symbols .................................................................................................. 2 4
2.14Dangers in case of non-compliance with the safety instructions ........................................... 25
2.15Safety-conscious working ...................................................................................................... 25
2.16Safety information for users ................................................................................................... 26
2.16.1General safety instructions and accident prevention instructions .......................................... 26
2.16.2Hydraulic system .................................................................................................................... 30
2.16.3Electrical system .................................................................................................................... 31
2.16.4Mounted implements .............................................................................................................. 32
2.16.5Operation of the seed drill ...................................................................................................... 33
2.16.6Cleaning, maintenance and repair ......................................................................................... 34
3Loading and unloading the implement upon delivery ............................ 35
4Product description ................................................................................... 36
4.1Components of the AMAZONE seeding combination ........................................................... 36
4.2Assembly groups of the AD-P Special pneumatic pack top seed drill ................................... 37
4.3Safety and protection equipment ........................................................................................... 39
4.4Overview – Supply cable / hydraulic hose lines ..................................................................... 40
4.4.1Supply cable........................................................................................................................... 40
4.4.2Identification of the hydraulic hose lines ................................................................................ 40
4.4.3Type of actuation of the tractor control units .......................................................................... 40
4.4.4Connection and function of the tractor control units with and without ISOBUS
system .................................................................................................................................... 41
4.5Traffic safety equipment ......................................................................................................... 42
4.6Proper use .............................................................................................................................. 4 3
4.7Danger areas and danger points ........................................................................................... 44
4.8Rating plate and CE mark ...................................................................................................... 45
4.9Technical data ........................................................................................................................ 46
4.10Noise production data ............................................................................................................ 46
4.10.1Technical data for calculating the tractor weight and the tractor axle loads .......................... 47
4.11Required tractor equipment ................................................................................................... 4 8
5Structure and function .............................................................................. 49
5.1AMAZONE AmaDrill+ control terminal ................................................................................... 52
5.2Control terminal for implements with ISOBUS system .......................................................... 52
5.2.1AMAZONE AmaTron 4 control terminal ................................................................................. 53
5.2.2AMAZONE TwinTerminal ....................................................................................................... 53
5.2.3AMAZONE mySeeder app ..................................................................................................... 53
5.3Implement documentation ...................................................................................................... 54
6 AD-P 30/35/4001 SPECIAL BAH0095-3 06.20
5.4Central key ............................................................................................................................ 54
5.5Distance measurement ......................................................................................................... 55
5.6Seed hopper and loading board ............................................................................................ 56
5.6.1Fill level monitoring ................................................................................................................ 57
5.7Metering ................................................................................................................................ 58
5.7.1Metering roller table - Figures ............................................................................................... 60
5.7.2Table - Metering rollers, seed ............................................................................................... 62
5.7.3Calibrating the seed rate ....................................................................................................... 64
5.7.4Automatic seed rate increase ................................................................................................ 65
5.8Fan ........................................................................................................................................ 66
5.9Distributor head ..................................................................................................................... 68
5.9.1Seed tube monitoring ............................................................................................................ 69
5.9.2Spreading seed with wide row spacing ................................................................................. 69
5.10WS drag coulter ..................................................................................................................... 70
5.10.1Band seeding shoe................................................................................................................ 70
5.11RoTeC Control coulter .......................................................................................................... 71
5.12Coulter pressure, coulter lift and harrow lift .......................................................................... 73
5.12.1Coulter pressure - Mechanical adjustment ........................................................................... 73
5.12.2Coulter pressure - Hydraulic adjustment ............................................................................... 74
5.12.3Coulter and harrow lift - Soil tillage without seeding ............................................................. 75
5.13Exact following harrow .......................................................................................................... 75
5.13.1Exact following harrow tine position ...................................................................................... 76
5.13.2Exact following harrow pressure ........................................................................................... 77
5.14Roller harrow ......................................................................................................................... 78
5.15Seeding variations, adjustable on the control terminal ......................................................... 79
5.15.1Adapting the seed rate to the acceleration of the tractor ...................................................... 79
5.15.2Seeding in field corners ......................................................................................................... 79
5.16Tramlines ............................................................................................................................... 80
5.16.1Tramline rhythm, tabular determination ................................................................................ 82
5.16.2Tramline rhythm, graphic determination................................................................................ 82
5.16.3One-sided switching .............................................................................................................. 84
5.16.3.1One-sided switching by installing an insert ........................................................................... 84
5.16.3.2One-sided switching by pressing a button ............................................................................ 85
5.16.4Tramline marker .................................................................................................................... 85
5.17Track marker ......................................................................................................................... 86
5.18Camera system with monitor ................................................................................................. 87
5.19Work floodlights ..................................................................................................................... 87
6Initial operation .......................................................................................... 88
6.1Checking the suitability of the tractor .................................................................................... 89
6.1.1Calculation of the actual values for the total tractor weight, tractor axle loads and
tyre load-bearing capacity, as well as the required minimum ballast weight ........................ 90
6.1.1.1Data required for the calculation (attached implement) ........................................................ 91
6.1.1.2Calculation of the required minimum ballast weight at the front GV min of the tractor
to ensure steering capability ................................................................................................. 92
6.1.1.3Calculation of the actual front axle load of the tractor TV tat ................................................... 92
6.1.1.4Calculation of the actual total weight of the combined tractor and implement ...................... 92
6.1.1.5Calculation of the actual rear axle load of the tractor TH tat ................................................... 92
6.1.1.6Load-bearing capacity of the tractor tyres ............................................................................. 92
6.1.1.7Table ..................................................................................................................................... 93
6.2Secure the tractor / implement against unintentional starting and rolling away ................... 94
6.3Hydraulic connection for the blower fan drive ....................................................................... 95
7Coupling and uncoupling the implement ................................................ 96
7.1Hydraulic hose lines .............................................................................................................. 98
7.1.1Coupling the hydraulic hose lines ......................................................................................... 98
7.1.2Disconnecting the hydraulic hose lines ................................................................................. 99
7.2Coupling and uncoupling implements ................................................................................. 100
7.2.1Coupling the soil tillage implement ...................................................................................... 102
AD-P 30/35/4001 SPECIAL BAH0095-3 06.20 7
7.2.2Coupling the pack top seed drill ........................................................................................... 105
7.2.3Uncoupling the combination ................................................................................................. 109
7.2.4Uncoupling the pack top seed drill ....................................................................................... 109
8Settings ..................................................................................................... 114
8.1Folding the steps up and down ............................................................................................ 115
8.2Fill the seed hopper ............................................................................................................. 117
8.3Calibrating the seed rate ...................................................................................................... 119
8.3.1Adjusting the automatic seed rate increase ......................................................................... 120
8.4Adjusting the fan speed ....................................................................................................... 121
8.4.1Setting the blower fan speed via the flow control valve of the tractor.................................. 122
8.4.2Setting the fan speed on tractors without flow control valve ................................................ 122
8.4.3Switching on the blower fan speed monitoring .................................................................... 122
8.4.4Pressure relief valve with round outer contour .................................................................... 123
8.4.4.1Basic setting of the pressure relief valve ............................................................................. 123
8.4.4.2Blower fan speed setting ...................................................................................................... 123
8.4.5Pressure relief valve with hexagonal outer contour ............................................................. 124
8.4.5.1Basic setting of the pressure relief valve ............................................................................. 124
8.4.5.2Blower fan speed setting ...................................................................................................... 124
8.5Adjusting and checking the seed placement depth ............................................................. 125
8.6RoTeC Control coulter ......................................................................................................... 126
8.6.1Adjusting the depth control discs / wheels ........................................................................... 126
8.7Coulter pressure .................................................................................................................. 128
8.7.1.1Mechanical coulter pressure adjustment ............................................................................. 128
8.7.1.2Hydraulic coulter pressure adjustment ................................................................................ 128
8.7.2Soil tillage without seeding - Lifting the coulters and harrow ............................................... 129
8.8Adjusting the exact following harrow ................................................................................... 130
8.8.1Adjusting the exact following harrow tines ........................................................................... 130
8.8.2Setting the exact following harrow pressure ........................................................................ 131
8.8.3Moving the exact following harrow to the working/transport position .................................. 132
8.8.3.1Move the exact following harrow into working position ........................................................ 132
8.8.3.2Moving the exact following harrow into transport position ................................................... 132
8.9Adjusting the roller harrow ................................................................................................... 133
8.9.1Tines - Adjusting the pitch .................................................................................................... 133
8.9.2Tines - Adjusting the working depth ..................................................................................... 133
8.9.3Setting the roller contact pressure ....................................................................................... 134
8.9.4Lifting/lowering the roller harrow .......................................................................................... 136
8.9.4.1Lifting the roller harrow (deactivate) .................................................................................... 136
8.9.4.2Lowering the roller harrow (activate) ................................................................................... 137
8.10Moving the track marker to the working / transport position ................................................ 138
8.11Track markers on the seed drill............................................................................................ 139
8.11.1Moving the track marker into working position ..................................................................... 139
8.11.2Adjusting the track marker length ........................................................................................ 139
8.11.3Moving the track marker to transport position ...................................................................... 140
8.12One-sided switching ............................................................................................................. 141
8.12.1One-sided switching - Installing an insert ............................................................................ 141
8.12.2One-sided switching - setting on the control terminal .......................................................... 141
8.13Moving the tramline marker into working/transport position ................................................ 142
8.13.1Move the tramline marker to working position ..................................................................... 142
8.13.2Move the tramline markers to the transport position............................................................ 144
8.14Moving the exact following harrow road safety bar into road transport/parking
position ................................................................................................................................. 145
8.14.1Moving the road safety bar into road transport position ...................................................... 145
8.14.2Moving the road safety bar into parking position ................................................................. 145
8.15Moving the pulse wheel into the working/transport position ................................................ 146
8.15.1Moving the pulse wheel to working position ........................................................................ 146
8.15.2Moving the pulse wheel to transport position ....................................................................... 147
9Transportation ......................................................................................... 148
9.1Moving the seeding combination into transport position ...................................................... 148
8 AD-P 30/35/4001 SPECIAL BAH0095-3 06.20
9.2Legal regulations and safety ............................................................................................... 149
10Use of the implement .............................................................................. 153
10.1Initial operation .................................................................................................................... 154
10.2Work floodlights ................................................................................................................... 154
10.3Moving the implement from transport into working position ................................................ 155
10.4Work commencement ......................................................................................................... 155
10.5During operation .................................................................................................................. 156
10.5.1Overview of the inspections ................................................................................................ 156
10.5.2Turning at end of the field ................................................................................................... 157
10.5.3Track marker ....................................................................................................................... 158
10.5.4End of work on the field ....................................................................................................... 159
10.6Emptying the seed hopper and/or metering unit and replacing the metering roller ............ 160
11Faults ........................................................................................................ 164
11.1Residual seed quantity display ............................................................................................ 165
11.2Deviations between the set and actual seed rate ............................................................... 165
12Maintenance and repairs ........................................................................ 166
12.1Maintenance schedule ........................................................................................................ 166
12.2Safety .................................................................................................................................. 167
12.2.1Safety when cleaning the implement .................................................................................. 168
12.2.2Safety when working on the distributor head ...................................................................... 170
12.2.3Safety when working on the hydraulic system .................................................................... 170
12.3Visual inspections ................................................................................................................ 171
12.3.1Visual inspection of the upper and lower link pins .............................................................. 171
12.3.2Visual check of the hydraulic hose lines and couplings ...................................................... 171
12.3.2.1Date of manufacture of the hydraulic hose line ................................................................... 171
12.4Repairs ................................................................................................................................ 172
12.4.1Cleaning the fan suction protective screen ......................................................................... 172
12.4.2Cleaning the fan rotor .......................................................................................................... 172
12.4.3Cleaning the distributors head and checking the seed hoses for impurities ...................... 172
12.5Installations ......................................................................................................................... 173
12.5.1Installing plugs to increase the row spacings ...................................................................... 173
12.5.2Shutdown of the implement over a long period of time ....................................................... 173
12.6Workshop work .................................................................................................................... 174
12.6.1Initial installation of coupling parts ...................................................................................... 174
12.6.1.1Soil tillage implements type 00: Overview of the coupling parts ......................................... 178
12.6.1.2Soil tillage implements type 00: coupling part installation ................................................... 178
12.6.1.3Soil tillage implements type 01: overview of the coupling parts .......................................... 183
12.6.1.4Soil tillage implements type 01: coupling part installation ................................................... 184
12.6.2Adjusting the tramline control .............................................................................................. 186
12.6.2.1Setting the tramline track width ........................................................................................... 187
12.6.2.2Setting the tramline wheelmark width ................................................................................. 187
12.6.2.3Removing and installing the segment in the distributor head ............................................. 188
12.6.2.4Electrical connection of the tramline segments ................................................................... 189
12.6.2.5Deactivating tramline segments .......................................................................................... 190
12.6.3Exchanging the exact following harrow and the roller harrow with each other ................... 191
12.6.4Checking the hydraulic hose lines ....................................................................................... 192
12.6.4.1Safety when working on hydraulic hose lines ..................................................................... 193
12.7Oils and greases ................................................................................................................. 194
12.7.1Lubricants for grease nipples and grease guns .................................................................. 194
12.8Bolt tightening torques ........................................................................................................ 195
13Hydraulic diagram ................................................................................... 196
13.1AD-P Special hydraulic diagram ......................................................................................... 196
AD-P 30/35/4001 SPECIAL BAH0095-3 06.20 9
User information
10 AD-P 30/35/4001 SPECIAL BAH0095-3 06.20
1 User information
The User information section provides information concerning the operating manual.
This operating manual is valid for all versions of the implement.
Figures serve as a reference and are to be understood as representations of the principle.
All of the equipment is described without indicating it as special equipment. A description may be
provided for equipment that is not fitted on the implement or is only available in certain markets. The
sales documents provide information on the equipment of your implement or consult your service
partner for more detailed information.
All information in this operating manual corresponds to the state of knowledge at the time of publica-
tion. Due to ongoing development of the implement, deviations are possible between the implement
and the information in this operating manual. No claims can be made based on differences in the
specifications, figures or descriptions.
If you want to sell the implement, ensure that the operating manual is supplied with the implement.
The operating manual
describes the operation and maintenance of the implement
provides important information on safe and efficient handling of the implement
is an integral part of the implement and should always be kept with the implement or the towing
vehicle
must be kept in a safe place for future use.
Activities to be carried out by the user are presented as numbered instructions. Always observe the
sequence of the instructions. The reaction to instructions is indicated by an arrow where applicable.
Example:
1. Instruction 1
Reaction of the implement to handling instruction 1
2. Instruction 2
Listings without a mandatory sequence are presented as a listing with bullets.
Example: Point 1
Point 2
Numbers in round brackets refer to the item numbers in the illustrations. The first number refers to the
diagram and the second number to the item.
Example: (Fig. 3/6) = Figure 3 / Item 6.
All the directions specified in the operating manual are always viewed in the direction of travel.
General Safety Information
AD-P 30/35/4001 SPECIAL BAH0095-3 06.20 11
2 General Safety Information
This section contains important information on safe operation of the implement.
2.1 Obligations and liability
Comply with the instructions in the operating manual
Knowledge of the basic safety information and safety regulations is a basic requirement for safe han-
dling and fault-free implement operation.
Obligations of the operator
The operator is obliged only to let those people work with/on the implement who
are aware of the basic workplace safety information and accident prevention regulations
have been trained in working with/on the implement
have read and understood this operating manual.
The operator is obliged
to keep all the warning symbols on the implement in a legible state
to replace damaged warning symbols.
Obligations of the user
Before starting work, anyone charged with working with/on the machine is obliged
to comply with the basic workplace safety instructions and accident prevention regulations
to read and understand the "General safety information" section of this operating manual
to read the section "Warning symbols and other labels on the implement" in this operating manu-
al and to follow the safety instructions represented by the warning symbols when operating the
implement
to get to know the implement
to read the sections of this operating manual, important for carrying out your work.
If the user discovers that a function is not working properly, then they must eliminate this fault immedi-
ately. If this is not the task of the user or if the user does not have the appropriate technical
knowledge, then they should report this fault to their superior (operator).
General Safety Information
12 AD-P 30/35/4001 SPECIAL BAH0095-3 06.20
Risks in handling the implement
The implement has been constructed to the state-of-the art and the recognised rules of safety. How-
ever, operating the implement may cause risks and restrictions
the health and safety of the user or third persons
the implement itself
other property.
Only use the implement
for the purpose for which it was intended
in a perfect state of repair.
Eliminate any faults immediately which could impair safety.
Guarantee and liability
Our "General conditions of sales and delivery" are always applicable. These shall be available to the
operator, at the latest on conclusion of the contract. Guarantee and liability claims for damage to
people or property will be excluded if they can be traced back to one or more of the following causes:
Improper use of the implement
Improper installation, commissioning, operation and maintenance of the implement
Operation of the implement with defective safety equipment or improperly attached or non-
functioning safety and protective equipment
Non-compliance with the instructions in the operating manual regarding commissioning, opera-
tion and maintenance
Unauthorised design changes to the implement
Insufficient monitoring of implement parts which are subject to wear
Improperly executed repairs
Disasters due to the effects of foreign objects and force majeure.
General Safety Information
AD-P 30/35/4001 SPECIAL BAH0095-3 06.20 13
2.2 Representation of safety symbols
Safety information is indicated by the triangular safety symbol and the highlighted signal word. The
signal word (DANGER, WARNING, CAUTION) describes the severity of the risk, and carries the
following meaning:
DANGER
Indicates an immediate hazard with high risk, which will result
in death or serious bodily harm (loss of limbs or long-term
harm), if it is not avoided.
If the instructions are not followed, then this will result in im-
mediate death or serious physical injury.
WARNING
Indicates a medium risk, which could result in death or (serious)
physical injury if not avoided.
If the instructions are not followed, then this may result in death
or serious physical injury.
CAUTION
Indicates a low risk which could cause minor or medium level
physical injury or damage to property if not avoided.
IMPORTANT
Indicates an obligation to special behaviour or an activity required for
proper implement handling.
Non-compliance with these instructions can cause faults on the
implement or disturbance to the environment.
NOTE
Indicates handling tips and particularly useful information.
These instructions will help you to use all the functions of your imple-
ment in the best way possible.
General Safety Information
14 AD-P 30/35/4001 SPECIAL BAH0095-3 06.20
2.3 Organisational measures
The operator must provide the necessary personal protective equipment as per the information pro-
vided by the manufacturer of the crop protection agent to be used, such as:
Safety glasses
Protective shoes
Chemical-resistant overalls
Skin protection agents, etc.
The operating manual
must always be kept at the place at which the implement is
operated
must always be easily accessible for the user and maintenance
personnel.
Check all the available safety equipment regularly.
2.4 Safety and protective equipment
Before starting up the implement each time, all the safety and protection equipment must be properly
attached and fully functional. Check all safety and protection equipment regularly.
Faulty safety equipment
Faulty or disassembled safety and protection equipment can lead to dangerous situations.
2.5 Informal safety measures
As well as all the safety information in this operating manual, comply with the general, national regula-
tions pertaining to accident prevention and environmental protection.
When driving on public roads and routes you should comply with the statutory road traffic regulations.
General Safety Information
AD-P 30/35/4001 SPECIAL BAH0095-3 06.20 15
2.6 User training
Only those people who have been trained and instructed may work with/on the implement. The opera-
tor must clearly specify the responsibilities of the people charged with operation and maintenance
work.
People being trained may only work with/on the implement under the supervision of an experienced
person.
Person
Activity
Person special-
ly trained for the
activity 1)
Trained opera-
tor 2)
Person with specialist
training (specialist work-
shop) 3)
Loading/Transport X X X
Initial operation X
Set-up, tool installation X
operation X
Maintenance X
Troubleshooting and fault elimina-
tion
X X
Disposal X
Key: X..permitted ..not permitted
1) A person who can assume a specific task and who can carry out this task for an appropriately
qualified company.
2) Instructed persons are those who have been instructed in their assigned tasks and in the possi-
ble risks in the case of improper behaviour, have been trained if necessary, and have been in-
formed about the necessary protective equipment and measures.
3) Persons with specialised technical training shall be considered as a specialist. Due to their spe-
cialist training and their knowledge of the appropriate regulations, they can evaluate the work with
which they have been charged and detect possible dangers.
Comment:
A qualification equivalent to specialist training can be obtained from several years' experience in
the relevant field.
Only a specialist workshop may carry out maintenance and repair
work on the implement, if such work is additionally marked "Special-
ist workshop". The personnel of a specialist workshop shall possess
the appropriate knowledge and suitable aids (tools, lifting and sup-
port equipment) for carrying out the maintenance and repair work on
the implement in a way which is both appropriate and safe.
General Safety Information
16 AD-P 30/35/4001 SPECIAL BAH0095-3 06.20
2.7 Safety measures in normal operation
Only operate the implement if all the safety and protection equipment is fully functional.
Check the implement at least once a day for visible damage and check the function of the safety and
protection equipment.
2.8 Danger from residual energy
Note that there may be residual mechanical, hydraulic, pneumatic and electrical/electronic energy on the
implement.
Use appropriate measures to inform the operator. You can find detailed information in the relevant
sections of this operating manual.
2.9 Maintenance and repair work, fault elimination
Carry out prescribed setting, maintenance and inspection work in good time.
Secure all media such as compressed air and the hydraulic system against unintentional start-up.
Carefully fix and secure larger assembly groups to lifting units when carrying out replacement work.
Check all the bolted connections for tightness. On completion of the maintenance work, check the
function of the safety and protective devices.
2.10 Design changes
You may make no changes, expansions or modifications to the implement without the authorisation of
AMAZONEN-WERKE. This also applies when welding support parts.
Any extension or conversion work shall require the written approval of AMAZONEN-WERKE. Only use
conversion and special equipment parts approved by AMAZONEN-WERKEN so that the operating
permit, for example, remains valid in accordance with national and international regulations.
Vehicles with an official type approval or with equipment connected to a vehicle with a valid type
approval or approval for road transport according to the German road traffic regulations must be in the
state specified by the approval.
WARNING
Risk of crushing, cutting, being trapped or drawn in, or impact
through the failure of support parts.
It is strictly forbidden to
drill holes in the frame or on the running gear
increase the size of existing holes on the frame or the running gear
weld on load-bearing parts.
General Safety Information
AD-P 30/35/4001 SPECIAL BAH0095-3 06.20 17
2.10.1 Spare and wear parts and aids
Immediately replace any implement parts which are not in a perfect state.
Use only genuine AMAZONE spare and wear parts or the parts cleared by AMAZONEN-WERKE so
that the operating permit retains its validity in accordance with national and international regulations. If
you use wear and spare parts from third parties, there is no guarantee that they have been designed
and manufactured in such a way as to meet the requirements placed on them.
AMAZONEN-WERKE shall accept no liability for damage caused by the use of non-approved spare
and wear parts or aids.
2.11 Cleaning and disposal
Handle and dispose of any materials used carefully, in particular
when carrying out work on lubrication systems and equipment and
when cleaning using solvents.
2.12 Workstation of the operator
The implement may be operated by only one person sitting in the driver's seat of the tractor.
General Safety Information
18 AD-P 30/35/4001 SPECIAL BAH0095-3 06.20
2.13 Warning symbols on the implement
Always keep all the warning symbols of the implement clean and in a
legible state. Replace illegible warning symbols. You can request the
warning symbols from your AMAZONE dealer using the order number
(e.g., MD 075).
Structure
Warning symbols indicate danger areas on the implement and warn against residual dangers. At these
points, there are permanent or unexpected dangers.
A warning symbol consists of two fields.
Field 1
Shows the danger in a triangular safety symbol.
Field 2
Shows instructions for avoiding the danger.
Explanatory text beside the warning symbol
The text beside the warning symbol describes
1. The dangers, e.g.:
Laceration or amputation hazard.
2. The consequence of non-compliance with the risk avoidance instructions, e.g.:
This danger can cause serious injuries to fingers or hands.
3. Instructions for avoiding the risk, e.g.:
Touch machinery parts only when they have come to a complete stop.
General Safety Information
AD-P 30/35/4001 SPECIAL BAH0095-3 06.20 19
MD 078
Risk of crushing of fingers/hand by accessi-
ble, moving parts of the implement!
This hazard can cause extremely serious injuries
resulting in the loss of limbs.
Never reach into the danger area when the
tractor engine is running with the universal joint
shaft or hydraulic / electronic system connected.
MD 082
Risk of falling when riding the implement on
treads or platforms!
Causes serious, potentially fatal injuries any-
where on the body.
It is forbidden to ride on the implement or climb
the implement when it is running. This prohibition
also applies to implements with step surfaces or
platforms.
Make sure that nobody is riding on the imple-
ment.
MD 095
Before commissioning the machine read and
observe the operating manual and the safety
instructions carefully!
General Safety Information
20 AD-P 30/35/4001 SPECIAL BAH0095-3 06.20
MD 096
Danger from escaping high-pressure hydrau-
lic fluid due to leaking hydraulic hose lines!
This danger may cause serious injuries, perhaps
even resulting in death, if escaping high-
pressure hydraulic fluid passes through the skin
and into the body.
Never attempt to plug leaks in hydraulic
hose lines using your hand or fingers.
Read and observe the instructions in the
operating manual before carrying out any
maintenance or repair work on the hydraulic
hose lines.
If you are injured by hydraulic fluid, contact
a doctor immediately.
MD 097
Risk of crushing the entire body when stand-
ing in the lifting area of the 3-point linkage
when the 3-point hydraulic system is being
operated!
Causes serious, potentially fatal injuries any-
where on the body.
It is forbidden to stand in the lifting area of
the 3-point linkage when actuating the 3-
point hydraulic system.
Actuate the operator controls for the trac-
tor's three-point hydraulic system:
only from the designated workstation
under no circumstances if you are in
the lifting area between the tractor and
implement.
Other manuals for AD-P 3001 Special 850
1
This manual suits for next models
5
Table of contents
Other Amazone Farm Equipment manuals
Amazone
Amazone AD-P 03 SPECIAL User manual
Amazone
Amazone KE 3002 Installation instructions
Amazone
Amazone CombiDisc 3000 Installation instructions
Amazone
Amazone Cayros M Installation instructions
Amazone
Amazone EDX 9000-TC User manual
Amazone
Amazone Certos 4001-2TX User manual
Amazone
Amazone AmaSpread 2 User manual
Amazone
Amazone Precea 3000-A Installation instructions
Amazone
Amazone ZA-X Perfect 02 User manual
Amazone
Amazone CATROS 7501-2T User manual
Amazone
Amazone Cayena 6001 User manual
Amazone
Amazone EasyCheck Installation instructions
Amazone
Amazone Groundkeeper SmartCut GH 1350 User manual
Amazone
Amazone FTender 1600 Installation instructions
Amazone
Amazone Certos 4002-2TX User manual
Amazone
Amazone Hektor User manual
Amazone
Amazone Tyrok 400 OL Quick guide
Amazone
Amazone GHD 1500 User manual
Amazone
Amazone Avant 6002-2 Installation instructions
Amazone
Amazone Tyrok 400 Installation instructions
Popular Farm Equipment manuals by other brands
Sola
Sola ARGO Starting manual
Sulky
Sulky Xeos TF Original instructions
Raven
Raven AutoBoom XRT installation manual
Field Tuff
Field Tuff FTF-05SDTC owner's manual
Urban Coop Company
Urban Coop Company Round-Top Sustain Coop Assembly instructions
Lipco
Lipco Reversing Harrow UF 80L Translation of the original instructions
GSi
GSi BFT Anchor Point installation manual
Toro
Toro Groundsmaster 4500-D Operator's manual
Land Pride
Land Pride HR35 SERIES Operator's manual
Redexim
Redexim DS800 Operating and parts manual
GrainPro
GrainPro COLLAPSIBLE DRYER CASE II instruction manual
Horizont Agrar
Horizont Agrar EQUISTOP M3 Operating instruction