Amazone Centaya 3000 Super 1600 User manual
Operating manual
az
Pneumatic pack top seed drill
Centaya 3000/3500/4000 Super 1600
Centaya 3000/3500/4000 Super 2000
MG6194
BAH0092-3 01.19
Please read and observe this
operating manual before initial
operation of the implement!
Keep it in a safe place for future use!
en
2 Centaya Super BAH0092-3 01.19
Reading the instruction
manual and to adhere to it should not appear to
be inconvenient and superfluous as it is not
enough to hear from others and to realise that a
machine is good, to buy it and to believe that now
everything would work by itself. The person con-
cerned would not only harm himself but also
make the mistake of blaming the machine for the
reason of a possible failure instead of himself. In
order to ensure a good success one should go into
the mind of a thing or make himself familiar with
every part of the machine and to get acquainte
d
with its handling. Only this way, you would be
satisfied both with the machine as also with
yourself. To achieve this is the purpose of this in-
struction manual.
Leipzig-Plagwitz 1872.
Centaya Super BAH0092-3 01.19 3
Identification data
Please insert the identification data of the implement. The identifica-
tion data are arranged on the rating plate.
Implement number (ten digits):
Type:
Year of manufacture:
Basic weight [kg]:
Permissible total weight [kg]:
Maximum load [kg]:
Manufacturer address
AMAZONEN-WERKE
H. DREYER GmbH & Co. KG
Postfach 51
D-49202
Tel.:
Email:
Hasbergen, Germany
+ 49 (0) 5405 50 1-0
Spare parts order
Spare parts lists are freely accessible in the spare parts portal at
www.amazone.de.
Please send orders to your AMAZONE dealer.
Formalities of the operating manual
Type: Centaya Super
Document number: MG6194
Compilation date: 01.19
Copyright AMAZONEN-WERKE H. DREYER GmbH & Co. KG, 01.19
All rights reserved.
Reprinting, even of sections, only possible with the approval of
AMAZONEN-WERKE H. DREYER GmbH & Co. KG.
4 Centaya Super BAH0092-3 01.19
Foreword
Dear Customer,
You have chosen one of the quality products from the wide product range of AMAZONEN-WERKE,
H. DREYER GmbH & Co. KG. We thank you for your trust in our products
On receiving the implement, check to see if it has been damaged during transport or if parts are miss-
ing. Using the delivery note, check that the implement has been delivered in full, including any special
equipment ordered. Damage can only be rectified if problems are claimed immediately.
Before initial operation, read and observe this operating manual, and particularly the safety information.
Only after careful reading will you be able to benefit from the full scope of your newly purchased im-
plement.
Please ensure that all the implement operators have read this operating manual before they put the
implement into operation.
Should you have any questions or problems, please consult this operating manual or contact your lo-
cal service partner.
Regular maintenance and timely replacement of worn or damaged parts increases the service life of
your implement.
User information
Centaya Super BAH0092-3 01.19 5
1User information ........................................................................................ 10
1.1Purpose of the document ....................................................................................................... 10
1.2Locations in the operating manual ......................................................................................... 10
1.3Diagrams ................................................................................................................................ 10
2General safety instructions ....................................................................... 12
2.1Obligations and liability .......................................................................................................... 12
2.2Representation of safety symbols .......................................................................................... 14
2.3Organisational measures ....................................................................................................... 15
2.4Safety and protective equipment ........................................................................................... 15
2.5Informal safety measures ....................................................................................................... 15
2.6User training ........................................................................................................................... 16
2.7Safety measures in normal operation .................................................................................... 17
2.8Danger from residual energy ................................................................................................. 17
2.9Maintenance and repair work, fault elimination ..................................................................... 17
2.10Design changes ..................................................................................................................... 18
2.10.1Spare and wear parts and aids .............................................................................................. 19
2.11Cleaning and disposal ............................................................................................................ 19
2.12User workstation .................................................................................................................... 19
2.13Warning symbols and other labels on the implement ............................................................ 20
2.13.1Position of warning symbols .................................................................................................. 2 4
2.14Dangers in case of non-compliance with the safety instructions ........................................... 26
2.15Safety-conscious working ...................................................................................................... 26
2.16Safety information for users ................................................................................................... 27
2.16.1General safety instructions and accident prevention instructions .......................................... 28
2.16.2Hydraulic system .................................................................................................................... 32
2.16.3Electrical system .................................................................................................................... 32
2.16.4Mounted implements .............................................................................................................. 34
2.16.5Operation of the seed drill ...................................................................................................... 35
2.16.6Cleaning, maintenance and repair ......................................................................................... 35
3Loading and unloading the implement upon delivery ............................ 36
4Product description ................................................................................... 39
4.1Components of the AMAZONE seeding combination ........................................................... 39
4.2Equipment variations of the Centaya pneumatic pack top seed drill ..................................... 40
4.3Components of the Centaya pneumatic pack top seed drill .................................................. 42
4.4Safety and protective equipment ........................................................................................... 44
4.5Overview – Supply cable / hydraulic hose lines ..................................................................... 45
4.5.1Supply cable........................................................................................................................... 45
4.5.2Identification of the hydraulic hose lines ................................................................................ 45
4.5.3Type of actuation of the tractor control units .......................................................................... 45
4.5.4Connection and function of the tractor control units .............................................................. 46
4.5.5Comfort hydraulic system - Implements with ISOBUS system .............................................. 47
4.6Traffic safety equipment ......................................................................................................... 48
4.7Intended use .......................................................................................................................... 49
4.7.1Approved AMAZONE implement combinations ..................................................................... 50
4.8Danger areas and danger points ........................................................................................... 51
4.9Rating plate and CE mark ...................................................................................................... 52
4.10Technical data ........................................................................................................................ 53
4.11Noise production data ............................................................................................................ 53
4.11.1Technical data for calculating the tractor weight and the tractor axle loads .......................... 54
4.12Required tractor equipment ................................................................................................... 5 5
5Layout and function ................................................................................... 56
5.1AMAZONE AmaDrill 2 control terminal .................................................................................. 59
User information
6 Centaya Super BAH0092-3 01.19
5.2AMAZONE calibration button ................................................................................................ 59
5.3Control terminal for implements with ISOBUS system .......................................................... 59
5.3.1AMAZONE AmaTron 4 control terminal ................................................................................ 60
5.3.2AMAZONE TwinTerminal ...................................................................................................... 60
5.1Implement documentation ..................................................................................................... 61
5.2Central key ............................................................................................................................ 61
5.3Hand wash tank ..................................................................................................................... 61
5.4Radar device ......................................................................................................................... 62
5.5Seed hopper and loading board ............................................................................................ 63
5.5.1Fill level monitoring ................................................................................................................ 64
5.6Metering ................................................................................................................................ 65
5.6.1Metering roller diagram table - figures .................................................................................. 67
5.6.2Table – metering rollers, seed ............................................................................................... 70
5.6.3Calibrating the seed rate ....................................................................................................... 72
5.7Blower fan ............................................................................................................................. 75
5.8Distributor head ..................................................................................................................... 77
5.8.1Seed tube monitoring ............................................................................................................ 78
5.9Spreading seed with wide row spacing ................................................................................. 79
5.10RoTeC-Pro Control coulter .................................................................................................... 80
5.11TwinTeC double disc coulter ................................................................................................. 82
5.11.1Seed placement depth (TwinTeC) ........................................................................................ 84
5.12Coulter pressure, seed rate increase and coulter lift (all coulter types -
hydraulically actuated) .......................................................................................................... 85
5.12.1.1Coulter pressure .................................................................................................................... 85
5.12.1.2Activating the seed rate increase .......................................................................................... 86
5.12.1.3Coulter lift .............................................................................................................................. 87
5.13Exact following harrow .......................................................................................................... 88
5.13.1Exact following harrow tine position ...................................................................................... 89
5.13.2Exact following harrow pressure ........................................................................................... 90
5.13.3Seeding without exact following harrow (exact following harrow lift) .................................... 91
5.14Seed pre-metering................................................................................................................. 92
5.15Start-up ramp ........................................................................................................................ 92
5.16Tramlines ............................................................................................................................... 93
5.16.1Tramline rhythm, tabular determination ................................................................................ 96
5.16.2Tramline rhythm, graphic determination................................................................................ 96
5.16.3One-sided switching .............................................................................................................. 98
5.16.3.1One-sided switching by installing an insert ........................................................................... 98
5.16.3.2One-sided switching by actuating a lever ............................................................................. 99
5.16.3.3One-sided switching by pressing a button on the control terminal ..................................... 100
5.17Tramline marker .................................................................................................................. 101
5.17.1Tramline marker with bracket on the implement frame ....................................................... 101
5.17.2Tramline marker with bracket on the exact following harrow .............................................. 102
5.18Track marker ....................................................................................................................... 103
5.19Camera system ................................................................................................................... 104
5.20Headlight ............................................................................................................................. 105
5.21GreenDrill 200E ................................................................................................................... 106
6Start-up .................................................................................................... 107
6.1Checking the suitability of the tractor .................................................................................. 108
6.1.1Calculating the actual values for the total tractor weight, tractor axle loads and tyre
load-bearing capacity, as well as the required minimum ballast weight ............................. 109
6.1.1.1Data required for the calculation (attached implement) ...................................................... 110
6.1.1.2Calculation of the required minimum ballast weight at the front GV min of the tractor
to ensure steering capability ............................................................................................... 111
6.1.1.3Calculation of the actual front axle load of the tractor TV tat ................................................. 111
6.1.1.4Calculation of the actual total weight of the combined tractor and implement ................... 111
6.1.1.5Calculation of the actual rear axle load of the tractor TH tat ................................................. 111
6.1.1.6Load-bearing capacity of the tractor tyres ........................................................................... 111
User information
Centaya Super BAH0092-3 01.19 7
6.1.1.7Table .................................................................................................................................... 112
6.2Secure the tractor / implement against unintentional starting and rolling away ................. 113
6.3Hydraulic connection for the blower fan drive ...................................................................... 114
7Coupling and uncoupling the implement .............................................. 115
7.1Hydraulic hose lines ............................................................................................................. 117
7.1.1Coupling the hydraulic hose lines ........................................................................................ 117
7.1.2Disconnecting the hydraulic hose lines ................................................................................ 118
7.2Coupling and uncoupling implements .................................................................................. 119
7.2.1Coupling - Tractor and soil tillage implement ....................................................................... 121
7.2.1.1Installation of the analogue working position sensor and the working position
sensor for the seed tube monitoring .................................................................................... 122
7.2.2Coupling - Pack top seed drill and soil tillage implement .................................................... 126
7.2.3Uncoupling – Combination and tractor ................................................................................ 130
7.2.4Uncoupling – Soil tillage implement and pack top seed drill ............................................... 131
7.2.5Checking the tramline track width ........................................................................................ 136
7.2.6Checking the tramline wheelmark width .............................................................................. 136
8Settings ..................................................................................................... 137
8.1Folding the steps up and down ............................................................................................ 138
8.2Fill the seed hopper ............................................................................................................. 140
8.3Calibrating the seed rate ...................................................................................................... 143
8.4Setting the blower fan speed ............................................................................................... 149
8.4.1Setting the blower fan speed via the flow control valve of the tractor.................................. 150
8.4.2Setting the blower fan speed on tractors without flow control valve .................................... 150
8.4.3Switching on the blower fan speed monitoring .................................................................... 150
8.4.4Pressure relief valve with round outer contour .................................................................... 151
8.4.4.1Basic setting of the pressure relief valve ............................................................................. 151
8.4.4.2Blower fan speed setting ...................................................................................................... 151
8.4.5Pressure relief valve with hexagonal outer contour ............................................................. 152
8.4.5.1Basic setting of the pressure relief valve ............................................................................. 152
8.4.5.2Blower fan speed setting ...................................................................................................... 152
8.5RoTeC-Pro Control coulter .................................................................................................. 153
8.5.1Adjusting and checking the seed placement depth ............................................................. 153
8.5.1.1Adjusting the depth control discs / wheels ........................................................................... 154
8.6TwinTeC double disc coulter ................................................................................................ 156
8.6.1Adjusting and checking the seed placement depth ............................................................. 156
8.7Coulter pressure, seed rate increase and coulter lift (all coulter types -
hydraulically actuated) ......................................................................................................... 160
8.7.1Increasing / reducing the coulter pressure ........................................................................... 161
8.7.2Adjusting the seed rate increase ......................................................................................... 161
8.7.3Soil tillage without seeding (coulter lift) ................................................................................ 162
8.8Adjusting the exact following harrow ................................................................................... 163
8.8.1Adjusting the exact following harrow tines ........................................................................... 163
8.8.2Setting the exact following harrow pressure ........................................................................ 164
8.8.3Moving the exact following harrow to the working/transport position .................................. 165
8.8.3.1Move the exact following harrow into working position ........................................................ 165
8.8.3.2Moving the exact following harrow into transport position ................................................... 165
8.8.4Seeding without exact following harrow (exact following harrow lift) ................................... 165
8.9Moving the track marker to the working / transport position ................................................ 166
8.9.1Move track marker to working position ................................................................................ 166
8.9.2Moving the track marker to transport position ...................................................................... 168
8.10One-sided switching ............................................................................................................. 169
8.10.1One-sided switching - Installing an insert ............................................................................ 169
8.10.2One-sided switching - Lever actuation ................................................................................. 170
8.10.3One-sided switching - setting on the control terminal .......................................................... 170
8.11Moving the tramline marker into working/transport position ................................................ 171
8.11.1Moving the tramline marker with frame bracket to working position .................................... 171
8.11.2Moving the tramline markers with frame bracket to the transport position .......................... 172
8.11.3Move the tramline marker to working position with exact following harrow bracket ........... 173
User information
8 Centaya Super BAH0092-3 01.19
8.11.4Move the tramline marker to working position with exact following harrow bracket .......... 174
8.12Moving the exact following harrow road safety bar into road transport/parking
position ................................................................................................................................ 175
8.12.1Moving the road safety bar into road transport position ...................................................... 175
8.12.2Moving the road safety bar into parking position ................................................................ 175
9Transportation ......................................................................................... 176
9.1Moving the seeding combination into transport position ..................................................... 176
9.2Legal regulations and safety ............................................................................................... 177
10Use of the implement .............................................................................. 181
10.1Initial operation .................................................................................................................... 182
10.2Headlight ............................................................................................................................. 182
10.3Moving the implement from transport into working position ................................................ 183
10.4Work commencement ......................................................................................................... 183
10.5During operation .................................................................................................................. 185
10.5.1Overview of checks during operation .................................................................................. 185
10.5.2Turning at end of the field ................................................................................................... 186
10.5.3Track marker ....................................................................................................................... 187
10.5.4End of work on the field ....................................................................................................... 188
10.6Emptying the hopper and metering unit and replacing the metering roller ........................ 189
10.6.1Quick emptying of the hopper ............................................................................................. 190
10.6.2Emptying the hopper and/or metering unit and replacing the metering roller ..................... 191
11Faults ........................................................................................................ 194
11.1Residual seed quantity display ............................................................................................ 195
11.2Deviations between the set and actual seed rate ............................................................... 195
12Cleaning, maintenance and repairs ....................................................... 196
12.1Safety .................................................................................................................................. 196
12.1.1Safety when working on hydraulic hose lines ..................................................................... 198
12.1.1.1Safety through labelling the hydraulic hose lines ................................................................ 199
12.2Safety when cleaning the implement .................................................................................. 200
12.2.1Safety when working on the distributor head ...................................................................... 202
12.3Cleaning the implement ...................................................................................................... 202
12.3.1Cleaning the fan suction guard screen................................................................................ 202
12.3.2Cleaning the blower fan ...................................................................................................... 202
12.3.3Clean the distributor head ................................................................................................... 203
12.4Lubrication schedule ........................................................................................................... 204
12.4.1Lubrication points ................................................................................................................ 204
12.5Maintenance schedule ........................................................................................................ 205
12.6Adjustment and maintenance work ..................................................................................... 207
12.6.1Mount the plugs in the distributor head for spreading seed with wide row spacing ........... 207
12.6.2Parking the implement for a longer period of time .............................................................. 208
12.6.3Visual inspection of the upper and lower link pins .............................................................. 208
12.7Work to be performed in a specialist workshop .................................................................. 209
12.7.1Checking the hydraulic hose lines ....................................................................................... 209
12.7.2Adjusting the tramlines on the distributor head ................................................................... 210
12.7.2.1Adjusting the tramline track width on the distributor head .................................................. 211
12.7.2.2Adjusting the tramline wheelmark width on the distributor head ......................................... 211
12.7.2.3Removing and installing the segment in the distributor head ............................................. 212
12.7.2.4Electrical connection of the tramline segments ................................................................... 213
12.7.2.5Deactivating tramline segments .......................................................................................... 214
12.7.3Replacing the grid on the RoTeC Pro Control coulter ......................................................... 215
12.7.4Checking and readjusting the TwinTeC disc bearings ........................................................ 216
12.7.4.1Checking the TwinTeC disc bearings .................................................................................. 216
12.7.4.2Readjusting the TwinTeC disc bearings ............................................................................. 216
12.7.5Dismounting the TwinTeC seed line ................................................................................... 218
12.7.6Checking / replacing the TwinTeC inner scraper ................................................................ 218
12.7.7Checking / replacing the TwinTeC baffle lip ........................................................................ 219
User information
Centaya Super BAH0092-3 01.19 9
12.7.8Checking / replacing the TwinTeC press roller .................................................................... 219
12.7.9Checking / readjusting / replacing the TwinTeC roller scraper ............................................ 220
12.8Bolt tightening torques ......................................................................................................... 221
13Hydraulic diagram .................................................................................... 224
13.1Hydraulics plan with/without Comfort hydraulic system Centaya 3000/3500/4000
Super with RoTeC coulters .................................................................................................. 224
13.2Hydraulics plan with/without Comfort hydraulic system Centaya 3000/3500/4000
Super with RoTeC coulters .................................................................................................. 226
User information
10 Centaya Super BAH0092-3 01.19
1 User information
The User Information section provides information on use of the operating manual.
This operating manual is valid for all versions of the implement.
Figures serve as a reference and are to be understood as representations of the principle.
All of the equipment is described without indicating it as special optional equipment. A description may
be provided for equipment that is not fitted on the implement or is only available in certain markets.
The sales documents provide information on the equipment of your implement or consult your service
partner for more detailed information.
All information in this operating manual corresponds to the state of knowledge at the time of publica-
tion. Due to ongoing development of the implement, deviations are possible between the implement
and the information in this operating manual. No claims can be made based on differences in the
specifications, figures or descriptions.
If you want to sell the implement, ensure that the operating manual is supplied with the implement.
1.1 Purpose of the document
This operating manual
describes the operation and maintenance of the implement
provides important information on safe and efficient handling of
the implement
is an integral part of the implement and should always be kept
with the implement or the towing vehicle
must be kept in a safe place for future use.
1.2 Locations in the operating manual
A
ll the directions specified in the operating manual are always seen in
the direction of travel.
1.3 Diagrams
Instructions and responses
Activities to be carried out by the user are given as numbered instruc-
tions. Always keep to the order of the instructions. The reaction to the
handling instructions is given by an arrow. Example:
1. Instruction 1
Reaction of the implement to handling instruction 1
2. Instruction 2
User information
Centaya Super BAH0092-3 01.19 11
Lists
Lists without an essential order are shown as a list with bullets. Ex-
ample:
Point 1
Point 2
Item numbers in diagrams
Numbers in round brackets refer to the item numbers in the diagrams.
The first number refers to the diagram and the second number to the
item.
Example (Fig. 3/6):
Figure 3
Item 6
General safety instructions
12 Centaya Super BAH0092-3 01.19
2 General safety instructions
This section contains important information on safe operation of the
implement.
2.1 Obligations and liability
Comply with the instructions in the operating manual
Knowledge of the basic safety information and safety regulations is a
basic requirement for safe handling and fault-free implement opera-
tion.
Obligations of the operator
The operator is obliged only to let those people work with/on the im-
plement who
are aware of the basic workplace safety information and accident
prevention regulations
have been trained in working with/on the implement
have read and understood this operating manual.
The operator is obliged
to keep all the warning symbols on the implement in a legible
state
to replace damaged warning symbols.
Obligations of the user
Before starting work, anyone charged with working with/on the imple-
ment is obliged
to comply with the basic workplace safety instructions and acci-
dent prevention regulations
to read and understand the "General safety information" section
of this operating manual
to read the section "Warning symbols and other labels on the
implement" in this operating manual and to follow the safety in-
structions represented by the warning symbols when operating
the implement
to get to know the implement
to read the sections of this operating manual, important for carry-
ing out your work.
If the user discovers that a function is not working properly, then they
must eliminate this fault immediately. If this is not the task of the user
or if the user does not have the appropriate technical knowledge, then
they should report this fault to their superior (operator).
General safety instructions
Centaya Super BAH0092-3 01.19 13
Risks in handling the implement
The implement has been constructed to the state-of-the art and the
recognised rules of safety. However, operating the implement may
cause risks and restrictions
the health and safety of the user or third persons
the implement itself
other property.
Only use the implement
for the purpose for which it was intended
in a perfect state of repair.
Eliminate any faults immediately which could impair safety.
Guarantee and liability
Our "General conditions of sales and delivery" are always applicable.
These shall be available to the operator, at the latest on conclusion of
the contract. Guarantee and liability claims for damage to people or
property will be excluded if they can be traced back to one or more of
the following causes:
Improper use of the implement
Improper installation, commissioning, operation and mainte-
nance of the implement
Operation of the implement with defective safety equipment or
improperly attached or non-functioning safety and protective
equipment
Non-compliance with the instructions in the operating manual re-
garding commissioning, operation and maintenance
Unauthorised design changes to the implement
Insufficient monitoring of implement parts which are subject to
wear
Improperly executed repairs
Disasters due to the effects of foreign objects and force majeure.
General safety instructions
14 Centaya Super BAH0092-3 01.19
2.2 Representation of safety symbols
Safety instructions are indicated by the triangular safety symbol and
the highlighted signal word. The signal word (DANGER, WARNING,
CAUTION) describes the severity of the risk, and carries the following
meaning:
DANGER
Indicates a direct threat at high risk which will result in death or
most serious bodily harm (loss of limbs or long-term harm),
should it not be prevented.
If the instructions are not followed, then this will result in imme-
diate death or serious physical injury.
WARNING
Indicates a medium risk, which could result in death or (serious)
physical injury if not avoided.
If the instructions are not followed, then this may result in death
or serious physical injury.
CAUTION
Indicates a low risk which could cause minor or medium level
physical injury or damage to property if not avoided.
IMPORTANT
Indicates an obligation to special behaviour or an activity re-
quired for proper machine handling.
Non-compliance with these instructions can cause faults on the
machine or disturbance to the environment.
NOTE
Indicates handling tips and particularly useful information.
These instructions will help you to use all the functions of your
machine in the best way possible.
General safety instructions
Centaya Super BAH0092-3 01.19 15
2.3 Organisational measures
The operator must provide the necessary personal protective equip-
ment as per the information provided by the manufacturer of the crop
protection agent to be used, such as:
Safety glasses
Protective shoes
Chemical-resistant overalls
Skin protection agents, etc.
The operation manual
must always be kept at the place at which the implement is op-
erated
must always be easily accessible for the user and maintenance
personnel.
Check all the available safety equipment regularly.
2.4 Safety and protective equipment
Before starting up the implement each time, all the safety and protec-
tion equipment must be properly attached and fully functional. Check
all safety and protection equipment regularly.
Faulty safety equipment
Faulty or disassembled safety and protection equipment can lead to
dangerous situations.
2.5 Informal safety measures
As well as all the safety information in this operating manual, comply
with the general, national regulations pertaining to accident prevention
and environmental protection.
When driving on public roads and routes you should comply with the
statutory road traffic regulations.
General safety instructions
16 Centaya Super BAH0092-3 01.19
2.6 User training
Only those people who have been trained and instructed may work with/on the implement. The opera-
tor must clearly specify the responsibilities of the people charged with operation and maintenance
work.
People being trained may only work with/on the implement under the supervision of an experienced
person.
Person
Job
Person specially
trained for the
activity 1)
Trained per-
son 2)
Persons with
specialist
training (specialist
workshop) 3)
Loading/Transport X X X
Start-up X
Set-up, tool installation X
Operation X
Maintenance X
Troubleshooting and fault elimi-
nation
X X
Disposal X
Legend: X..permitted ..not permitted
1) A person who can assume a specific task and who can carry out this task for an appropriately
qualified company.
2) Instructed persons are those who have been instructed in their assigned tasks and in the possi-
ble risks in the case of improper behaviour, have been trained if necessary, and have been in-
formed about the necessary protective equipment and measures.
3) Persons with specialised technical training shall be considered as a specialist. Due to their spe-
cialist training and their knowledge of the appropriate regulations, they can evaluate the work with
which they have been charged and detect possible dangers.
Comment:
A qualification equivalent to specialist training can be obtained from several years' experience in
the relevant field.
Only a specialist workshop may carry out maintenance and repair
work on the implement, if such work is additionally marked "Work-
shop". The personnel of a specialist workshop shall possess the ap-
propriate knowledge and suitable aids (tools, lifting and support
equipment) for carrying out the maintenance and repair work on the
implement in a way which is both appropriate and safe.
General safety instructions
Centaya Super BAH0092-3 01.19 17
2.7 Safety measures in normal operation
Only operate the implement if all the safety and protection equipment
is fully functional.
Check the implement at least once a day for visible damage and
check the function of the safety and protection equipment.
2.8 Danger from residual energy
Note that there may be residual mechanical, hydraulic, pneumatic and
electrical/electronic energy on the implement.
Use appropriate measures to inform the operator. You can find de-
tailed information in the relevant sections of this operating manual.
2.9 Maintenance and repair work, fault elimination
Carry out prescribed setting, maintenance and inspection work in
good time.
Secure all media such as compressed air and the hydraulic system
against unintentional start-up.
Carefully fix and secure larger assembly groups to lifting gear when
carrying out replacement work.
Check all the bolted connections for tightness. On completion of the
maintenance work, check the function of the safety and protective de-
vices.
General safety instructions
18 Centaya Super BAH0092-3 01.19
2.10 Design changes
You may make no changes, expansions or modifications to the im-
plement without the authorisation of AMAZONEN-WERKE. This also
applies when welding support parts.
A
ny extension or conversion work shall require the written approval of
AMAZONEN-WERKE. Only use conversion and special equipment
parts approved by AMAZONEN-WERKE so that the operating permit,
for example, remains valid in accordance with national and interna-
tional regulations.
Vehicles with an official type approval or with equipment connected to
a vehicle with a valid type approval or approval for road transport ac-
cording to the German road traffic regulations must be in the state
specified by the approval.
WARNING
Risk of crushing, cutting, being trapped or drawn in, or impact
through the failure of support parts.
It is strictly forbidden to
drill holes in the frame or on the running gear
increase the size of existing holes on the frame or the running gear
weld on load-bearing parts.
General safety instructions
Centaya Super BAH0092-3 01.19 19
2.10.1 Spare and wear parts and aids
Immediately replace any implement parts which are not in a perfect
state.
Use only genuine AMAZONE spare and wear parts or the parts
cleared by AMAZONEN-WERKE so that the operating permit retains
its validity in accordance with national and international regulations. If
you use wear and spare parts from third parties, there is no guarantee
that they have been designed and manufactured in such a way as to
meet the requirements placed on them.
AMAZONEN-WERKE shall accept no liability for damage caused by
the use of non-approved spare and wear parts or aids.
2.11 Cleaning and disposal
Handle and dispose of any materials used carefully, in particular
when carrying out work on lubrication systems and equipment
and
when cleaning using solvents.
2.12 User workstation
The implement may be operated by only one person sitting in the
driver's seat of the tractor.
General safety instructions
20 Centaya Super BAH0092-3 01.19
2.13 Warning symbols and other labels on the implement
Always keep all the warning symbols of the implement clean and in a
legible state! Replace illegible warning symbols. You can request the
warning symbols from your AMAZONE dealer using the order number
(e.g., MD 075).
Structure
Warning symbols indicate danger areas on the implement and warn
against residual dangers. At these points, there are permanent or un-
expected dangers.
A warning symbol consists of two fields:
Field 1
Shows the danger in a triangular safety symbol.
Field 2
Shows instructions for avoiding the danger.
Explanatory text beside the warning symbol
The text beside the warning symbol describes
1. The dangers, e.g.:
Laceration or amputation hazard.
2. The consequence of non-compliance with the risk avoidance in-
structions, e.g.:
This danger can cause serious injuries to fingers or hands.
3. Instructions for avoiding the risk, e.g.:
Touch machinery parts only when they have come to a complete
stop.
Other manuals for Centaya 3000 Super 1600
1
This manual suits for next models
5
Table of contents
Other Amazone Farm Equipment manuals
Amazone
Amazone Cenius 3003 User manual
Amazone
Amazone Cenius 4003-2TX User manual
Amazone
Amazone Cayros M Installation instructions
Amazone
Amazone ZA-M 1800 Ultra Service manual
Amazone
Amazone TL 251 User manual
Amazone
Amazone CatrosXL 4003-2TS Installation instructions
Amazone
Amazone KG Special Series User manual
Amazone
Amazone Catros 7003-2TX User manual
Amazone
Amazone Amatron+ User manual
Amazone
Amazone Catros 4003-2 Installation instructions
Amazone
Amazone Cataya 3000 Special User manual
Amazone
Amazone Cirrus 03 User manual
Amazone
Amazone D9 2500 Special User manual
Amazone
Amazone ZA-X Perfect 602 User manual
Amazone
Amazone GreenDrill GD200-E User manual
Amazone
Amazone TSE 3000 User manual
Amazone
Amazone VK70181000 User manual
Amazone
Amazone ZG-TS 7501 Truck User manual
Amazone
Amazone DMC Primera 3000 User manual
Amazone
Amazone AMASPRAY+ User manual
Popular Farm Equipment manuals by other brands
CropCare
CropCare A116K Assembly & instruction manual
IronCraft
IronCraft FDM44 Operation and parts manual
Rain Harvesting
Rain Harvesting Clean Rain Ultra Installation and specification guide
Kerbl
Kerbl buddex 1716 user guide
Kerbl
Kerbl Air Buddex Instructions for use
Reinke
Reinke Ontrac Installation and service manual