Assa Abloy Yale YDD724A User manual

16. Internal Forced Lock
15. External Forced Lock
User Guide
RFID Key Tag / Fingerprint / PIN Code / Key
YDD724A
23. Master Mode
17. Alarm
18. 3 Minute Lock Out
19. Unlocking Door with Fake Code
Intrusion Alarm : The alarm goes off when someone forces the door open.
For example, In case of an intrusion by opening a gap
in the door while the door is locked.
Broken Alarm(Breakage Alarm) : The alarm goes off when the front part is
completely separated from the main set. For example,
forced removal of external product (front body).
Turn off Alarm
There is no limitation for
digits of Fake Pin Code.
Disable 3-minute Lock Out
All access mode from the external side are disabled for 3 minutes to deter
unauthorized access.
Press the Open/Close button.
Open the door with mechanical key.
Press button.
Enter the registered User Code.
Scan the registered fingerprint.
Press and hold the O/C Button for 5seconds.
Touch the registered RFID Key Tag.
20. Power supply
21. Emergency power supply for discharged batteries
One-on-one real life size
1.5V(LR6) Alkaline AA Battery
It may sustain 1 year if used 10 times
a day. (Users are advised to use
authentic Alkaline batteries.)
* Kindly dispose used batteries.
•
Do not install the digital door lock in an outdoor environment.
•
Do not attempt to disassemble the digital door lock by your self.
By doing so, you may get an electronic shock and damage the product.
•
Do not use force with a tool onto the product.
•
Make sure to lock the door tight when you go out.
•
Do not use water and any type of solvent to clean the product such as
gasoline or benzene as they can cause damage to electronic circuit,
deterioration and or paint peel-off.
•
It is recommended to change User Code on a regular basis.
•
In manual lock mode, make sure to double check whether the door is
securely locked.
•
When External Forced lock is set and unlock the door, the alarm will be
activated.
•
Do not use rechargeable batteries. Only alkaline batteries are recommended.
•
Make sure to follow the above instructions to avoid any injuries.
•
It cannot be guaranteed in a special conditions & environment such as
water condensation, seaside.
•
Warranty will not cover- exposure to dampness, excessive heat,
excessive humidity and other extreme environmental conditions,
corrosion, damage beyond repair, rusting, unauthorised modifications,
unauthorised repairs, neglect, accident, alteration, acts of God,
spillage of liquid or food particles.
Master mode is a mode in which only the administrator can set the door lock and provide
access to other users. 100 users passwords, 100 users RFID key tags,100 users fingerprint and
individual registration and deletion of one-time passwords enable efficient management of visitors.
Change
Mode New Again
Switch to master mode (from normal mode)
PIN CODE
UPIN CODE MPIN CODE M
Change
Mode New Again
Switch to normal mode (from master mode)
PIN CODE
UPIN CODE U
OR
Registr
-ation New Again
Master Pin Code Change
PIN CODE
M
PIN CODE
M
PIN CODE
M
Delete
OR
Registr
-ation
User Code
PIN CODE
U
UN
OR
UN
PIN CODE
M
Up to 100 Users
Only 1 User
Delete
OR
Registr
-ation
Fingerprint
UN
OR
UN
PIN CODE
M
Up to 100 Users
Delete
Registr
-ation
Onetime Code
OR
OR
PIN CODE
M
PIN CODE
M
PIN CODE
O
Only 1 User, Automatically deleted after use
Langu
-age
Setting
Language Change
OR
OR
OR
OR
OR
Delete
Delete all credentials
PIN CODE
M
PIN CODE
M
PIN CODE
M
Registr
-ation
Bluetooth Setting (Yale Access App)
PIN CODE
M
Delete
Registr
-ation
Remote Controller
OR
OR
PIN CODE
M
Up to 5 Users
UN
UN
Button
SET
Delete
Registr
-ation
Home Network Controller
OR
OR
PIN CODE
Mroller
Cont
PIN CODE
M
PIN CODE
M
Korean
Chinese
English
Taiwanese
8times
Set up a new device in the app
14 (Registration process)
1
High
Low
Mute
Volume Control
PIN CODE
M
OR
OR
OR
Disable
Enable
Automatic Lock
PIN CODE
M
Continue / Complete
Enable External Forced Lock : Fingerprint
Scan with registered fingerprint and hold the fingerprint area
until you hear 3 beep sounds.
Disable External Forced Lock
When the door is unlocked from outside based upon proper
authentication, the External forced lock will be released.
Palm touch Enter the
User PIN Code
Enter the
button for 5 Sec.
Enable External Forced Lock : User Code
※If you try to open a door with the manual thumb turn knob from inside when the Outside Forced Lock is set,
the alarm goes off.
※If the Inside Forced Lock is set, any attempt to open a door from outside whether it’s be a Fingerprint or
code won’t work.
Press Open/Close button
for 3 seconds until
you hear “pik” beep.
Method 1 :
Press Open/Close
button for 3 seconds
until you hear
“pik” beep.
Method 2 :
Turn manual
thumb turn knob.
Setting
‘ 3 ’
Seconds
Release
‘ 3 ’
Seconds
Turn it
OR
OR
ISL-1857-00-046
PLEASE READ INSTRUCTIONS BEFORE USE.
The functions and design of this product can be changed
without prior notice for performance and quality improvement.
Packaging of this product can be recycled.
User Slot Number should be 2 digits.
like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100".
※
22. Code Chart
Duplicate if necessary
PIN Code Management(Up to 100 Users.)
Do not install the digital door
lock in an outdoor environment.
24. Important notes
Do not attempt to disassemble
the digital door lock by yourself.
Do not spray water directly
or wipe with chemicals such as
benzene, gasoline or alcohol.
Do not use force with a tool
onto the product.
When using, remember that
someone else can see the
password.
Make sure the door is closed
properly when going out.
25. Safety and Warning
※Voice guidance : Voice guidance features assist in easy navigation through various features.
※All registered passwords and other credentials will be deleted when mode is changed.
※Please install(register) the network module when you want to use a remote control or home network.
Part of ASSA ABLOY
You must replace all 4 batteries in the following cases:
* The Low Battery LED on keypad flickers red.
* When low battery notification message is played.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE NATIONAL CODE OR RECYCLING PROGRAM.
Palm touch Palm touchEnter the user code
and fake code
Enter the Fake Code
and User code
OR
Enable External Forced Lock : RFID Key Tag
Contact RFID key tag on [RFID key tag reader] for 5 sec. until you
hear 3 beeps.
※In case of discharged batteries, please use 9V battery to supply power
Palm
touch
OR OR
Contact 9V
battery
Enter the User Code
and Plam touch
Contact
RFID Key Tag
Scan
fingerprint
Delete
OR
Registr
-ation
RFID Key Tag
UN
OR
UN
PIN CODE
M
Up to 100 Users

1. Front Body (Front Body, installation on the outside of the door)
2. Basic Contents
Basic Contents
5. Front Body
4. Main Body (Main Body, installation on the inside of the door) 7. Setting Menu 9. Normal Mode (Default Mode)
Front Body Main Body Main bracket
Dead Bolt & Strike Plate
Optional Accessories
Mechanical Keys
12. Unlocking Door with Smart Etiquette.
3. Specifications
※Battery life may vary depending on temperature, moisture levels, frequency of use and the quality of battery used.
※Please make sure that all parts are included when purchasing the product.
※Optional products may not be available depending on your country or local dealer.
※Even after a door was locked by the Auto Lock function,
please check again if the door was completely closed and locked.
11. Unlocking Door with Code
14. Locking the door
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds after
the door was closed.
Manual Lock status :
Touch the keypad
in the front body gently
with your palm to lock a door.
9V Emergency
alkaline battery
Emergency Key
6. Main Body
1
Fingerprint Sensor
2
Keypad(10-key)
3
RFID Key Tag reader
4
Dead Bolt Jam Lamp
6
Emergency Power Supply Terminal (Mechanical Key)
5
Low Battery Indicator
7
Emergency Power Supply Terminal (9V Emergency alkaline battery)
Touch the Keypad of the Front Body with your palm to begin
Press button on the Keypad
Press button on the Keypad
Press (Registration) button in every steps to start or
complete the session
Enter User Fingerprint
(Up to 100 Users)
Enter User Code (4 ~ 10 digits)
Enter Master Code (4 ~ 10 digits)
Enter Visitor Code (Only 4 digits)
Enter Onetime Code (Only 4 digits)
User Slot Number should be 2 digits
(like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100". )
Rotation area to add more features
Normal mode is for convenient mode for anyone with user code to change
various settings.
Registr
-ation New
Only 1 User
User Code
PIN CODE
U
OR
Registr
-ation 8times
Fingerprint Up to 100 Users
12 (Registration process)
1Continue / Complete
YDD724A
7
6
1
2
Optional
1
2
3
4
5
6
1
2
Module Accessory Slot (Optional)
3
1.5V AA Alkaline Batteries (4PCS)
4
Thumb turn knob
5
Battery Cover
6
Open / Close button
Registration button
Operating temperature
-15~55˚C (5~131˚F)
100 different RFID Key Tags,
fingerprints, User codes
Up to 100 RFID Key Tags,
fingerprints, User codes
Specifications RemarksParts
Front Body
Fingerprint,
RFID Key Tag,
User code
It lasts a year
if used 10 times a day.
Optional
3EA
4EA 1.5V AA Alkaline batteries
(Operating voltage: 4.5~6V)
Wireless
Optional Remote Controller
Emergency Key
Works for
Main Body
66(W) X 176(H) X 31.5(D), Zinc die-casting
70(W) X 170(H) X 35(D), ALDC
10. Unlocking Door with Fingerprint
13. Open/Close the door from inside
Close Door from Outside
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds
after the door was closed.
Manual Lock status :
Turn manual
thumb turn knob to
close the lock,
Into ‘Close’ marked direction.
Press Open/Close button.
Close Door from Inside
Open/Close button
To open the lock,
turn manual thumb turn knob
from 'Close' direction to
'Open' direction.
Thumb turn knob
5 Sec
5 Sec
8. Product Features
One Touch Fingerprint Access
Secure one Touch Live fingerprint detection for personalized access. Unique Sensor not only
provides high security but faster unlocking experience as well.
Yale Access App
Yale Access gives you the peace of mind of knowing who and what you love is safe - no matter
where you are- just at the touch of your smartphone.
Smart Touchpad – Auto Lock
The door Locks when you touch the palm on the keypad.
3 minute Lock Out Feature
After five (5) unsuccessful attempts of an invalid code or fingerprint, RFID Key Tag lock out
mode is activated for 3 minutes.
Smart Etiquette
When entering a pin code on the keypad, the user can open the door lock in silent mode.
Fake PIN Code
Security enhancement to enter any number before or after entering a password to prevent
the PIN code from being exposed.
Internal Forced Lock
It is a security-enhancing function that 'disables' authentication methods such as passwords
and fingerprints from outside when setting up functions indoors.
External Forced Lock
It is a security-enhancing function that an alarm goes off if someone opens door from inside
when setting up functions outside.
Voice Guidance
It guides you through the operation status on how to enable various features & settings- mode
for easier and more convenient use.
Other features and Benefits
•Remote Controller (Optional):
This option may not be available depending on your country or local dealer.
•Network Module/Controller (Optional):
It allows door lock to connect with Home network controller.
•Intrusion/Broken Alarm.
•Low Battery Alarm and Emergency Power Supply.
•User Manual
• Installation Guide
• Screws
• RFID Key Tags X 4
• Remote Controller
• Remote Control
Module
• Bluetooth Module
Palm touch Enter the Code Palm touch Enter the
button
OR
Delete all fingerprint credentials
Delete
PIN CODE
UPIN CODE
U
OR
Registr
-ation
Delete
Visitor Code
OR
OR
PIN CODE
U
PIN CODE
V
Registr
-ation
Delete
Onetime Code Only 1 User, Automatically deleted after use
OR
OR
PIN CODE
U
PIN CODE
O
Only 1 User
PIN CODE
U
PIN CODE
U
Enable
Disable
Automatic Lock
PIN CODE
U
OR
OR
OR
OR
OR
Volume Control
High
Low
Mute
Remote Controller
Set with registration button located on the top of remote controller.
You can press it using a pin like the one shown in the image.
Registr
-ation
Delete
Remote Controller
OR
OR
PIN CODE
U
Button
SET
Registr
-ation
Delete
Home Network Controller
OR
OR
PIN CODE
U
roller
Cont
PIN CODE
U
PIN CODE
U
Up to 5 Users
OR
OR
OR
OR
Registr
-ation
Language Change
Korean
Chinese
English
Taiwanese
PIN CODE
U
PIN CODE
U
Please note following when pairing lock with Yale Access App.
- Depending on product type or FW version, app registration and door lock connection in normal mode may not
be possible, so if registration is not possible, change from normal mode to master mode and try again.
[ App Registration in Master Mode: Master Pin Code-> R (Registration Button)-> 7 -> # ]
- Because Yale Access Bluetooth App is only available in master mode, user code automatically changes to
master code when registering APP in normal mode.
- Please be informed that all registered credentials will be deleted when changing mode or registering and
deleting app.
Registr
-ation
Bluetooth setting (Yale Access app)
PIN CODE
U
Set up a new device in the app
U
PIN CODE
M
PIN CODE
V
PIN CODE
O
PIN CODE
UN
Master Mode : Only a designated person who knows 'Master PIN Code' has authority
to set features.
Normal Mode:
If no user is assigned with master code without a designated person,
anyone who knows ‘User PIN Code’ has authority to set features.
Visitor Code: Users with Visitor Code can only open the door with no access to change
settings.
Onetime Code: The onetime code is used only once for unlocking the door lock and
automatically deleted after usage.
User Slot Number: It should be 2 digits(like ’01’, ‘02’…’99’, ‘00’) and available
in advanced mode.
3
4
5
Enter User RFID Key Tag (Up to 100 Users)
Registr
-ation
RFID Key Tag Up to 100 Users
Touch the panel of finger
print area sensor using
registered fingerprint
for 1 seconds.
Fingerprint
scan completed
Contact registered
RFID Key Tag
Palm touch
for 3sec.
Enter the User PIN Code
then touch the keypad
with your palm
Scan
Fingerprint
OR OR
Touch
RFID Key Tag

1. Front Body (Front Body, installation on the outside of the door)
2. Basic Contents
Basic Contents
5. Front Body
4. Main Body (Main Body, installation on the inside of the door) 7. Setting Menu 9. Normal Mode (Default Mode)
Front Body Main Body Main bracket
Dead Bolt & Strike Plate
Optional Accessories
Mechanical Keys
12. Unlocking Door with Smart Etiquette.
3. Specifications
※Battery life may vary depending on temperature, moisture levels, frequency of use and the quality of battery used.
※Please make sure that all parts are included when purchasing the product.
※Optional products may not be available depending on your country or local dealer.
※Even after a door was locked by the Auto Lock function,
please check again if the door was completely closed and locked.
11. Unlocking Door with Code
14. Locking the door
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds after
the door was closed.
Manual Lock status :
Touch the keypad
in the front body gently
with your palm to lock a door.
9V Emergency
alkaline battery
Emergency Key
6. Main Body
1
Fingerprint Sensor
2
Keypad(10-key)
3
RFID Key Tag reader
4
Dead Bolt Jam Lamp
6
Emergency Power Supply Terminal (Mechanical Key)
5
Low Battery Indicator
7
Emergency Power Supply Terminal (9V Emergency alkaline battery)
Touch the Keypad of the Front Body with your palm to begin
Press button on the Keypad
Press button on the Keypad
Press (Registration) button in every steps to start or
complete the session
Enter User Fingerprint
(Up to 100 Users)
Enter User Code (4 ~ 10 digits)
Enter Master Code (4 ~ 10 digits)
Enter Visitor Code (Only 4 digits)
Enter Onetime Code (Only 4 digits)
User Slot Number should be 2 digits
(like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100". )
Rotation area to add more features
Normal mode is for convenient mode for anyone with user code to change
various settings.
Registr
-ation New
Only 1 User
User Code
PIN CODE
U
OR
Registr
-ation 8times
Fingerprint Up to 100 Users
12 (Registration process)
1Continue / Complete
YDD724A
7
6
1
2
Optional
1
2
3
4
5
6
1
2
Module Accessory Slot (Optional)
3
1.5V AA Alkaline Batteries (4PCS)
4
Thumb turn knob
5
Battery Cover
6
Open / Close button
Registration button
Operating temperature
-15~55˚C (5~131˚F)
100 different RFID Key Tags,
fingerprints, User codes
Up to 100 RFID Key Tags,
fingerprints, User codes
Specifications RemarksParts
Front Body
Fingerprint,
RFID Key Tag,
User code
It lasts a year
if used 10 times a day.
Optional
3EA
4EA 1.5V AA Alkaline batteries
(Operating voltage: 4.5~6V)
Wireless
Optional Remote Controller
Emergency Key
Works for
Main Body
66(W) X 176(H) X 31.5(D), Zinc die-casting
70(W) X 170(H) X 35(D), ALDC
10. Unlocking Door with Fingerprint
13. Open/Close the door from inside
Close Door from Outside
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds
after the door was closed.
Manual Lock status :
Turn manual
thumb turn knob to
close the lock,
Into ‘Close’ marked direction.
Press Open/Close button.
Close Door from Inside
Open/Close button
To open the lock,
turn manual thumb turn knob
from 'Close' direction to
'Open' direction.
Thumb turn knob
5 Sec
5 Sec
8. Product Features
One Touch Fingerprint Access
Secure one Touch Live fingerprint detection for personalized access. Unique Sensor not only
provides high security but faster unlocking experience as well.
Yale Access App
Yale Access gives you the peace of mind of knowing who and what you love is safe - no matter
where you are- just at the touch of your smartphone.
Smart Touchpad – Auto Lock
The door Locks when you touch the palm on the keypad.
3 minute Lock Out Feature
After five (5) unsuccessful attempts of an invalid code or fingerprint, RFID Key Tag lock out
mode is activated for 3 minutes.
Smart Etiquette
When entering a pin code on the keypad, the user can open the door lock in silent mode.
Fake PIN Code
Security enhancement to enter any number before or after entering a password to prevent
the PIN code from being exposed.
Internal Forced Lock
It is a security-enhancing function that 'disables' authentication methods such as passwords
and fingerprints from outside when setting up functions indoors.
External Forced Lock
It is a security-enhancing function that an alarm goes off if someone opens door from inside
when setting up functions outside.
Voice Guidance
It guides you through the operation status on how to enable various features & settings- mode
for easier and more convenient use.
Other features and Benefits
•Remote Controller (Optional):
This option may not be available depending on your country or local dealer.
•Network Module/Controller (Optional):
It allows door lock to connect with Home network controller.
•Intrusion/Broken Alarm.
•Low Battery Alarm and Emergency Power Supply.
•User Manual
• Installation Guide
• Screws
• RFID Key Tags X 4
• Remote Controller
• Remote Control
Module
• Bluetooth Module
Palm touch Enter the Code Palm touch Enter the
button
OR
Delete all fingerprint credentials
Delete
PIN CODE
UPIN CODE
U
OR
Registr
-ation
Delete
Visitor Code
OR
OR
PIN CODE
U
PIN CODE
V
Registr
-ation
Delete
Onetime Code Only 1 User, Automatically deleted after use
OR
OR
PIN CODE
U
PIN CODE
O
Only 1 User
PIN CODE
U
PIN CODE
U
Enable
Disable
Automatic Lock
PIN CODE
U
OR
OR
OR
OR
OR
Volume Control
High
Low
Mute
Remote Controller
Set with registration button located on the top of remote controller.
You can press it using a pin like the one shown in the image.
Registr
-ation
Delete
Remote Controller
OR
OR
PIN CODE
U
Button
SET
Registr
-ation
Delete
Home Network Controller
OR
OR
PIN CODE
U
roller
Cont
PIN CODE
U
PIN CODE
U
Up to 5 Users
OR
OR
OR
OR
Registr
-ation
Language Change
Korean
Chinese
English
Taiwanese
PIN CODE
U
PIN CODE
U
Please note following when pairing lock with Yale Access App.
- Depending on product type or FW version, app registration and door lock connection in normal mode may not
be possible, so if registration is not possible, change from normal mode to master mode and try again.
[ App Registration in Master Mode: Master Pin Code-> R (Registration Button)-> 7 -> # ]
- Because Yale Access Bluetooth App is only available in master mode, user code automatically changes to
master code when registering APP in normal mode.
- Please be informed that all registered credentials will be deleted when changing mode or registering and
deleting app.
Registr
-ation
Bluetooth setting (Yale Access app)
PIN CODE
U
Set up a new device in the app
U
PIN CODE
M
PIN CODE
V
PIN CODE
O
PIN CODE
UN
Master Mode : Only a designated person who knows 'Master PIN Code' has authority
to set features.
Normal Mode:
If no user is assigned with master code without a designated person,
anyone who knows ‘User PIN Code’ has authority to set features.
Visitor Code: Users with Visitor Code can only open the door with no access to change
settings.
Onetime Code: The onetime code is used only once for unlocking the door lock and
automatically deleted after usage.
User Slot Number: It should be 2 digits(like ’01’, ‘02’…’99’, ‘00’) and available
in advanced mode.
3
4
5
Enter User RFID Key Tag (Up to 100 Users)
Registr
-ation
RFID Key Tag Up to 100 Users
Touch the panel of finger
print area sensor using
registered fingerprint
for 1 seconds.
Fingerprint
scan completed
Contact registered
RFID Key Tag
Palm touch
for 3sec.
Enter the User PIN Code
then touch the keypad
with your palm
Scan
Fingerprint
OR OR
Touch
RFID Key Tag

1. Front Body (Front Body, installation on the outside of the door)
2. Basic Contents
Basic Contents
5. Front Body
4. Main Body (Main Body, installation on the inside of the door) 7. Setting Menu 9. Normal Mode (Default Mode)
Front Body Main Body Main bracket
Dead Bolt & Strike Plate
Optional Accessories
Mechanical Keys
12. Unlocking Door with Smart Etiquette.
3. Specifications
※Battery life may vary depending on temperature, moisture levels, frequency of use and the quality of battery used.
※Please make sure that all parts are included when purchasing the product.
※Optional products may not be available depending on your country or local dealer.
※Even after a door was locked by the Auto Lock function,
please check again if the door was completely closed and locked.
11. Unlocking Door with Code
14. Locking the door
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds after
the door was closed.
Manual Lock status :
Touch the keypad
in the front body gently
with your palm to lock a door.
9V Emergency
alkaline battery
Emergency Key
6. Main Body
1
Fingerprint Sensor
2
Keypad(10-key)
3
RFID Key Tag reader
4
Dead Bolt Jam Lamp
6
Emergency Power Supply Terminal (Mechanical Key)
5
Low Battery Indicator
7
Emergency Power Supply Terminal (9V Emergency alkaline battery)
Touch the Keypad of the Front Body with your palm to begin
Press button on the Keypad
Press button on the Keypad
Press (Registration) button in every steps to start or
complete the session
Enter User Fingerprint
(Up to 100 Users)
Enter User Code (4 ~ 10 digits)
Enter Master Code (4 ~ 10 digits)
Enter Visitor Code (Only 4 digits)
Enter Onetime Code (Only 4 digits)
User Slot Number should be 2 digits
(like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100". )
Rotation area to add more features
Normal mode is for convenient mode for anyone with user code to change
various settings.
Registr
-ation New
Only 1 User
User Code
PIN CODE
U
OR
Registr
-ation 8times
Fingerprint Up to 100 Users
12 (Registration process)
1Continue / Complete
YDD724A
7
6
1
2
Optional
1
2
3
4
5
6
1
2
Module Accessory Slot (Optional)
3
1.5V AA Alkaline Batteries (4PCS)
4
Thumb turn knob
5
Battery Cover
6
Open / Close button
Registration button
Operating temperature
-15~55˚C (5~131˚F)
100 different RFID Key Tags,
fingerprints, User codes
Up to 100 RFID Key Tags,
fingerprints, User codes
Specifications RemarksParts
Front Body
Fingerprint,
RFID Key Tag,
User code
It lasts a year
if used 10 times a day.
Optional
3EA
4EA 1.5V AA Alkaline batteries
(Operating voltage: 4.5~6V)
Wireless
Optional Remote Controller
Emergency Key
Works for
Main Body
66(W) X 176(H) X 31.5(D), Zinc die-casting
70(W) X 170(H) X 35(D), ALDC
10. Unlocking Door with Fingerprint
13. Open/Close the door from inside
Close Door from Outside
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds
after the door was closed.
Manual Lock status :
Turn manual
thumb turn knob to
close the lock,
Into ‘Close’ marked direction.
Press Open/Close button.
Close Door from Inside
Open/Close button
To open the lock,
turn manual thumb turn knob
from 'Close' direction to
'Open' direction.
Thumb turn knob
5 Sec
5 Sec
8. Product Features
One Touch Fingerprint Access
Secure one Touch Live fingerprint detection for personalized access. Unique Sensor not only
provides high security but faster unlocking experience as well.
Yale Access App
Yale Access gives you the peace of mind of knowing who and what you love is safe - no matter
where you are- just at the touch of your smartphone.
Smart Touchpad – Auto Lock
The door Locks when you touch the palm on the keypad.
3 minute Lock Out Feature
After five (5) unsuccessful attempts of an invalid code or fingerprint, RFID Key Tag lock out
mode is activated for 3 minutes.
Smart Etiquette
When entering a pin code on the keypad, the user can open the door lock in silent mode.
Fake PIN Code
Security enhancement to enter any number before or after entering a password to prevent
the PIN code from being exposed.
Internal Forced Lock
It is a security-enhancing function that 'disables' authentication methods such as passwords
and fingerprints from outside when setting up functions indoors.
External Forced Lock
It is a security-enhancing function that an alarm goes off if someone opens door from inside
when setting up functions outside.
Voice Guidance
It guides you through the operation status on how to enable various features & settings- mode
for easier and more convenient use.
Other features and Benefits
•Remote Controller (Optional):
This option may not be available depending on your country or local dealer.
•Network Module/Controller (Optional):
It allows door lock to connect with Home network controller.
•Intrusion/Broken Alarm.
•Low Battery Alarm and Emergency Power Supply.
•User Manual
• Installation Guide
• Screws
• RFID Key Tags X 4
• Remote Controller
• Remote Control
Module
• Bluetooth Module
Palm touch Enter the Code Palm touch Enter the
button
OR
Delete all fingerprint credentials
Delete
PIN CODE
UPIN CODE
U
OR
Registr
-ation
Delete
Visitor Code
OR
OR
PIN CODE
U
PIN CODE
V
Registr
-ation
Delete
Onetime Code Only 1 User, Automatically deleted after use
OR
OR
PIN CODE
U
PIN CODE
O
Only 1 User
PIN CODE
U
PIN CODE
U
Enable
Disable
Automatic Lock
PIN CODE
U
OR
OR
OR
OR
OR
Volume Control
High
Low
Mute
Remote Controller
Set with registration button located on the top of remote controller.
You can press it using a pin like the one shown in the image.
Registr
-ation
Delete
Remote Controller
OR
OR
PIN CODE
U
Button
SET
Registr
-ation
Delete
Home Network Controller
OR
OR
PIN CODE
U
roller
Cont
PIN CODE
U
PIN CODE
U
Up to 5 Users
OR
OR
OR
OR
Registr
-ation
Language Change
Korean
Chinese
English
Taiwanese
PIN CODE
U
PIN CODE
U
Please note following when pairing lock with Yale Access App.
- Depending on product type or FW version, app registration and door lock connection in normal mode may not
be possible, so if registration is not possible, change from normal mode to master mode and try again.
[ App Registration in Master Mode: Master Pin Code-> R (Registration Button)-> 7 -> # ]
- Because Yale Access Bluetooth App is only available in master mode, user code automatically changes to
master code when registering APP in normal mode.
- Please be informed that all registered credentials will be deleted when changing mode or registering and
deleting app.
Registr
-ation
Bluetooth setting (Yale Access app)
PIN CODE
U
Set up a new device in the app
U
PIN CODE
M
PIN CODE
V
PIN CODE
O
PIN CODE
UN
Master Mode : Only a designated person who knows 'Master PIN Code' has authority
to set features.
Normal Mode:
If no user is assigned with master code without a designated person,
anyone who knows ‘User PIN Code’ has authority to set features.
Visitor Code: Users with Visitor Code can only open the door with no access to change
settings.
Onetime Code: The onetime code is used only once for unlocking the door lock and
automatically deleted after usage.
User Slot Number: It should be 2 digits(like ’01’, ‘02’…’99’, ‘00’) and available
in advanced mode.
3
4
5
Enter User RFID Key Tag (Up to 100 Users)
Registr
-ation
RFID Key Tag Up to 100 Users
Touch the panel of finger
print area sensor using
registered fingerprint
for 1 seconds.
Fingerprint
scan completed
Contact registered
RFID Key Tag
Palm touch
for 3sec.
Enter the User PIN Code
then touch the keypad
with your palm
Scan
Fingerprint
OR OR
Touch
RFID Key Tag

1. Front Body (Front Body, installation on the outside of the door)
2. Basic Contents
Basic Contents
5. Front Body
4. Main Body (Main Body, installation on the inside of the door) 7. Setting Menu 9. Normal Mode (Default Mode)
Front Body Main Body Main bracket
Dead Bolt & Strike Plate
Optional Accessories
Mechanical Keys
12. Unlocking Door with Smart Etiquette.
3. Specifications
※Battery life may vary depending on temperature, moisture levels, frequency of use and the quality of battery used.
※Please make sure that all parts are included when purchasing the product.
※Optional products may not be available depending on your country or local dealer.
※Even after a door was locked by the Auto Lock function,
please check again if the door was completely closed and locked.
11. Unlocking Door with Code
14. Locking the door
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds after
the door was closed.
Manual Lock status :
Touch the keypad
in the front body gently
with your palm to lock a door.
9V Emergency
alkaline battery
Emergency Key
6. Main Body
1
Fingerprint Sensor
2
Keypad(10-key)
3
RFID Key Tag reader
4
Dead Bolt Jam Lamp
6
Emergency Power Supply Terminal (Mechanical Key)
5
Low Battery Indicator
7
Emergency Power Supply Terminal (9V Emergency alkaline battery)
Touch the Keypad of the Front Body with your palm to begin
Press button on the Keypad
Press button on the Keypad
Press (Registration) button in every steps to start or
complete the session
Enter User Fingerprint
(Up to 100 Users)
Enter User Code (4 ~ 10 digits)
Enter Master Code (4 ~ 10 digits)
Enter Visitor Code (Only 4 digits)
Enter Onetime Code (Only 4 digits)
User Slot Number should be 2 digits
(like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100". )
Rotation area to add more features
Normal mode is for convenient mode for anyone with user code to change
various settings.
Registr
-ation New
Only 1 User
User Code
PIN CODE
U
OR
Registr
-ation 8times
Fingerprint Up to 100 Users
12 (Registration process)
1Continue / Complete
YDD724A
7
6
1
2
Optional
1
2
3
4
5
6
1
2
Module Accessory Slot (Optional)
3
1.5V AA Alkaline Batteries (4PCS)
4
Thumb turn knob
5
Battery Cover
6
Open / Close button
Registration button
Operating temperature
-15~55˚C (5~131˚F)
100 different RFID Key Tags,
fingerprints, User codes
Up to 100 RFID Key Tags,
fingerprints, User codes
Specifications RemarksParts
Front Body
Fingerprint,
RFID Key Tag,
User code
It lasts a year
if used 10 times a day.
Optional
3EA
4EA 1.5V AA Alkaline batteries
(Operating voltage: 4.5~6V)
Wireless
Optional Remote Controller
Emergency Key
Works for
Main Body
66(W) X 176(H) X 31.5(D), Zinc die-casting
70(W) X 170(H) X 35(D), ALDC
10. Unlocking Door with Fingerprint
13. Open/Close the door from inside
Close Door from Outside
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds
after the door was closed.
Manual Lock status :
Turn manual
thumb turn knob to
close the lock,
Into ‘Close’ marked direction.
Press Open/Close button.
Close Door from Inside
Open/Close button
To open the lock,
turn manual thumb turn knob
from 'Close' direction to
'Open' direction.
Thumb turn knob
5 Sec
5 Sec
8. Product Features
One Touch Fingerprint Access
Secure one Touch Live fingerprint detection for personalized access. Unique Sensor not only
provides high security but faster unlocking experience as well.
Yale Access App
Yale Access gives you the peace of mind of knowing who and what you love is safe - no matter
where you are- just at the touch of your smartphone.
Smart Touchpad – Auto Lock
The door Locks when you touch the palm on the keypad.
3 minute Lock Out Feature
After five (5) unsuccessful attempts of an invalid code or fingerprint, RFID Key Tag lock out
mode is activated for 3 minutes.
Smart Etiquette
When entering a pin code on the keypad, the user can open the door lock in silent mode.
Fake PIN Code
Security enhancement to enter any number before or after entering a password to prevent
the PIN code from being exposed.
Internal Forced Lock
It is a security-enhancing function that 'disables' authentication methods such as passwords
and fingerprints from outside when setting up functions indoors.
External Forced Lock
It is a security-enhancing function that an alarm goes off if someone opens door from inside
when setting up functions outside.
Voice Guidance
It guides you through the operation status on how to enable various features & settings- mode
for easier and more convenient use.
Other features and Benefits
•Remote Controller (Optional):
This option may not be available depending on your country or local dealer.
•Network Module/Controller (Optional):
It allows door lock to connect with Home network controller.
•Intrusion/Broken Alarm.
•Low Battery Alarm and Emergency Power Supply.
•User Manual
• Installation Guide
• Screws
• RFID Key Tags X 4
• Remote Controller
• Remote Control
Module
• Bluetooth Module
Palm touch Enter the Code Palm touch Enter the
button
OR
Delete all fingerprint credentials
Delete
PIN CODE
UPIN CODE
U
OR
Registr
-ation
Delete
Visitor Code
OR
OR
PIN CODE
U
PIN CODE
V
Registr
-ation
Delete
Onetime Code Only 1 User, Automatically deleted after use
OR
OR
PIN CODE
U
PIN CODE
O
Only 1 User
PIN CODE
U
PIN CODE
U
Enable
Disable
Automatic Lock
PIN CODE
U
OR
OR
OR
OR
OR
Volume Control
High
Low
Mute
Remote Controller
Set with registration button located on the top of remote controller.
You can press it using a pin like the one shown in the image.
Registr
-ation
Delete
Remote Controller
OR
OR
PIN CODE
U
Button
SET
Registr
-ation
Delete
Home Network Controller
OR
OR
PIN CODE
U
roller
Cont
PIN CODE
U
PIN CODE
U
Up to 5 Users
OR
OR
OR
OR
Registr
-ation
Language Change
Korean
Chinese
English
Taiwanese
PIN CODE
U
PIN CODE
U
Please note following when pairing lock with Yale Access App.
- Depending on product type or FW version, app registration and door lock connection in normal mode may not
be possible, so if registration is not possible, change from normal mode to master mode and try again.
[ App Registration in Master Mode: Master Pin Code-> R (Registration Button)-> 7 -> # ]
- Because Yale Access Bluetooth App is only available in master mode, user code automatically changes to
master code when registering APP in normal mode.
- Please be informed that all registered credentials will be deleted when changing mode or registering and
deleting app.
Registr
-ation
Bluetooth setting (Yale Access app)
PIN CODE
U
Set up a new device in the app
U
PIN CODE
M
PIN CODE
V
PIN CODE
O
PIN CODE
UN
Master Mode : Only a designated person who knows 'Master PIN Code' has authority
to set features.
Normal Mode:
If no user is assigned with master code without a designated person,
anyone who knows ‘User PIN Code’ has authority to set features.
Visitor Code: Users with Visitor Code can only open the door with no access to change
settings.
Onetime Code: The onetime code is used only once for unlocking the door lock and
automatically deleted after usage.
User Slot Number: It should be 2 digits(like ’01’, ‘02’…’99’, ‘00’) and available
in advanced mode.
3
4
5
Enter User RFID Key Tag (Up to 100 Users)
Registr
-ation
RFID Key Tag Up to 100 Users
Touch the panel of finger
print area sensor using
registered fingerprint
for 1 seconds.
Fingerprint
scan completed
Contact registered
RFID Key Tag
Palm touch
for 3sec.
Enter the User PIN Code
then touch the keypad
with your palm
Scan
Fingerprint
OR OR
Touch
RFID Key Tag

1. Front Body (Front Body, installation on the outside of the door)
2. Basic Contents
Basic Contents
5. Front Body
4. Main Body (Main Body, installation on the inside of the door) 7. Setting Menu 9. Normal Mode (Default Mode)
Front Body Main Body Main bracket
Dead Bolt & Strike Plate
Optional Accessories
Mechanical Keys
12. Unlocking Door with Smart Etiquette.
3. Specifications
※Battery life may vary depending on temperature, moisture levels, frequency of use and the quality of battery used.
※Please make sure that all parts are included when purchasing the product.
※Optional products may not be available depending on your country or local dealer.
※Even after a door was locked by the Auto Lock function,
please check again if the door was completely closed and locked.
11. Unlocking Door with Code
14. Locking the door
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds after
the door was closed.
Manual Lock status :
Touch the keypad
in the front body gently
with your palm to lock a door.
9V Emergency
alkaline battery
Emergency Key
6. Main Body
1
Fingerprint Sensor
2
Keypad(10-key)
3
RFID Key Tag reader
4
Dead Bolt Jam Lamp
6
Emergency Power Supply Terminal (Mechanical Key)
5
Low Battery Indicator
7
Emergency Power Supply Terminal (9V Emergency alkaline battery)
Touch the Keypad of the Front Body with your palm to begin
Press button on the Keypad
Press button on the Keypad
Press (Registration) button in every steps to start or
complete the session
Enter User Fingerprint
(Up to 100 Users)
Enter User Code (4 ~ 10 digits)
Enter Master Code (4 ~ 10 digits)
Enter Visitor Code (Only 4 digits)
Enter Onetime Code (Only 4 digits)
User Slot Number should be 2 digits
(like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100". )
Rotation area to add more features
Normal mode is for convenient mode for anyone with user code to change
various settings.
Registr
-ation New
Only 1 User
User Code
PIN CODE
U
OR
Registr
-ation 8times
Fingerprint Up to 100 Users
12 (Registration process)
1Continue / Complete
YDD724A
7
6
1
2
Optional
1
2
3
4
5
6
1
2
Module Accessory Slot (Optional)
3
1.5V AA Alkaline Batteries (4PCS)
4
Thumb turn knob
5
Battery Cover
6
Open / Close button
Registration button
Operating temperature
-15~55˚C (5~131˚F)
100 different RFID Key Tags,
fingerprints, User codes
Up to 100 RFID Key Tags,
fingerprints, User codes
Specifications RemarksParts
Front Body
Fingerprint,
RFID Key Tag,
User code
It lasts a year
if used 10 times a day.
Optional
3EA
4EA 1.5V AA Alkaline batteries
(Operating voltage: 4.5~6V)
Wireless
Optional Remote Controller
Emergency Key
Works for
Main Body
66(W) X 176(H) X 31.5(D), Zinc die-casting
70(W) X 170(H) X 35(D), ALDC
10. Unlocking Door with Fingerprint
13. Open/Close the door from inside
Close Door from Outside
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds
after the door was closed.
Manual Lock status :
Turn manual
thumb turn knob to
close the lock,
Into ‘Close’ marked direction.
Press Open/Close button.
Close Door from Inside
Open/Close button
To open the lock,
turn manual thumb turn knob
from 'Close' direction to
'Open' direction.
Thumb turn knob
5 Sec
5 Sec
8. Product Features
One Touch Fingerprint Access
Secure one Touch Live fingerprint detection for personalized access. Unique Sensor not only
provides high security but faster unlocking experience as well.
Yale Access App
Yale Access gives you the peace of mind of knowing who and what you love is safe - no matter
where you are- just at the touch of your smartphone.
Smart Touchpad – Auto Lock
The door Locks when you touch the palm on the keypad.
3 minute Lock Out Feature
After five (5) unsuccessful attempts of an invalid code or fingerprint, RFID Key Tag lock out
mode is activated for 3 minutes.
Smart Etiquette
When entering a pin code on the keypad, the user can open the door lock in silent mode.
Fake PIN Code
Security enhancement to enter any number before or after entering a password to prevent
the PIN code from being exposed.
Internal Forced Lock
It is a security-enhancing function that 'disables' authentication methods such as passwords
and fingerprints from outside when setting up functions indoors.
External Forced Lock
It is a security-enhancing function that an alarm goes off if someone opens door from inside
when setting up functions outside.
Voice Guidance
It guides you through the operation status on how to enable various features & settings- mode
for easier and more convenient use.
Other features and Benefits
•Remote Controller (Optional):
This option may not be available depending on your country or local dealer.
•Network Module/Controller (Optional):
It allows door lock to connect with Home network controller.
•Intrusion/Broken Alarm.
•Low Battery Alarm and Emergency Power Supply.
•User Manual
• Installation Guide
• Screws
• RFID Key Tags X 4
• Remote Controller
• Remote Control
Module
• Bluetooth Module
Palm touch Enter the Code Palm touch Enter the
button
OR
Delete all fingerprint credentials
Delete
PIN CODE
UPIN CODE
U
OR
Registr
-ation
Delete
Visitor Code
OR
OR
PIN CODE
U
PIN CODE
V
Registr
-ation
Delete
Onetime Code Only 1 User, Automatically deleted after use
OR
OR
PIN CODE
U
PIN CODE
O
Only 1 User
PIN CODE
U
PIN CODE
U
Enable
Disable
Automatic Lock
PIN CODE
U
OR
OR
OR
OR
OR
Volume Control
High
Low
Mute
Remote Controller
Set with registration button located on the top of remote controller.
You can press it using a pin like the one shown in the image.
Registr
-ation
Delete
Remote Controller
OR
OR
PIN CODE
U
Button
SET
Registr
-ation
Delete
Home Network Controller
OR
OR
PIN CODE
U
roller
Cont
PIN CODE
U
PIN CODE
U
Up to 5 Users
OR
OR
OR
OR
Registr
-ation
Language Change
Korean
Chinese
English
Taiwanese
PIN CODE
U
PIN CODE
U
Please note following when pairing lock with Yale Access App.
- Depending on product type or FW version, app registration and door lock connection in normal mode may not
be possible, so if registration is not possible, change from normal mode to master mode and try again.
[ App Registration in Master Mode: Master Pin Code-> R (Registration Button)-> 7 -> # ]
- Because Yale Access Bluetooth App is only available in master mode, user code automatically changes to
master code when registering APP in normal mode.
- Please be informed that all registered credentials will be deleted when changing mode or registering and
deleting app.
Registr
-ation
Bluetooth setting (Yale Access app)
PIN CODE
U
Set up a new device in the app
U
PIN CODE
M
PIN CODE
V
PIN CODE
O
PIN CODE
UN
Master Mode : Only a designated person who knows 'Master PIN Code' has authority
to set features.
Normal Mode:
If no user is assigned with master code without a designated person,
anyone who knows ‘User PIN Code’ has authority to set features.
Visitor Code: Users with Visitor Code can only open the door with no access to change
settings.
Onetime Code: The onetime code is used only once for unlocking the door lock and
automatically deleted after usage.
User Slot Number: It should be 2 digits(like ’01’, ‘02’…’99’, ‘00’) and available
in advanced mode.
3
4
5
Enter User RFID Key Tag (Up to 100 Users)
Registr
-ation
RFID Key Tag Up to 100 Users
Touch the panel of finger
print area sensor using
registered fingerprint
for 1 seconds.
Fingerprint
scan completed
Contact registered
RFID Key Tag
Palm touch
for 3sec.
Enter the User PIN Code
then touch the keypad
with your palm
Scan
Fingerprint
OR OR
Touch
RFID Key Tag

1. Front Body (Front Body, installation on the outside of the door)
2. Basic Contents
Basic Contents
5. Front Body
4. Main Body (Main Body, installation on the inside of the door) 7. Setting Menu 9. Normal Mode (Default Mode)
Front Body Main Body Main bracket
Dead Bolt & Strike Plate
Optional Accessories
Mechanical Keys
12. Unlocking Door with Smart Etiquette.
3. Specifications
※Battery life may vary depending on temperature, moisture levels, frequency of use and the quality of battery used.
※Please make sure that all parts are included when purchasing the product.
※Optional products may not be available depending on your country or local dealer.
※Even after a door was locked by the Auto Lock function,
please check again if the door was completely closed and locked.
11. Unlocking Door with Code
14. Locking the door
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds after
the door was closed.
Manual Lock status :
Touch the keypad
in the front body gently
with your palm to lock a door.
9V Emergency
alkaline battery
Emergency Key
6. Main Body
1
Fingerprint Sensor
2
Keypad(10-key)
3
RFID Key Tag reader
4
Dead Bolt Jam Lamp
6
Emergency Power Supply Terminal (Mechanical Key)
5
Low Battery Indicator
7
Emergency Power Supply Terminal (9V Emergency alkaline battery)
Touch the Keypad of the Front Body with your palm to begin
Press button on the Keypad
Press button on the Keypad
Press (Registration) button in every steps to start or
complete the session
Enter User Fingerprint
(Up to 100 Users)
Enter User Code (4 ~ 10 digits)
Enter Master Code (4 ~ 10 digits)
Enter Visitor Code (Only 4 digits)
Enter Onetime Code (Only 4 digits)
User Slot Number should be 2 digits
(like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100". )
Rotation area to add more features
Normal mode is for convenient mode for anyone with user code to change
various settings.
Registr
-ation New
Only 1 User
User Code
PIN CODE
U
OR
Registr
-ation 8times
Fingerprint Up to 100 Users
12 (Registration process)
1Continue / Complete
YDD724A
7
6
1
2
Optional
1
2
3
4
5
6
1
2
Module Accessory Slot (Optional)
3
1.5V AA Alkaline Batteries (4PCS)
4
Thumb turn knob
5
Battery Cover
6
Open / Close button
Registration button
Operating temperature
-15~55˚C (5~131˚F)
100 different RFID Key Tags,
fingerprints, User codes
Up to 100 RFID Key Tags,
fingerprints, User codes
Specifications RemarksParts
Front Body
Fingerprint,
RFID Key Tag,
User code
It lasts a year
if used 10 times a day.
Optional
3EA
4EA 1.5V AA Alkaline batteries
(Operating voltage: 4.5~6V)
Wireless
Optional Remote Controller
Emergency Key
Works for
Main Body
66(W) X 176(H) X 31.5(D), Zinc die-casting
70(W) X 170(H) X 35(D), ALDC
10. Unlocking Door with Fingerprint
13. Open/Close the door from inside
Close Door from Outside
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds
after the door was closed.
Manual Lock status :
Turn manual
thumb turn knob to
close the lock,
Into ‘Close’ marked direction.
Press Open/Close button.
Close Door from Inside
Open/Close button
To open the lock,
turn manual thumb turn knob
from 'Close' direction to
'Open' direction.
Thumb turn knob
5 Sec
5 Sec
8. Product Features
One Touch Fingerprint Access
Secure one Touch Live fingerprint detection for personalized access. Unique Sensor not only
provides high security but faster unlocking experience as well.
Yale Access App
Yale Access gives you the peace of mind of knowing who and what you love is safe - no matter
where you are- just at the touch of your smartphone.
Smart Touchpad – Auto Lock
The door Locks when you touch the palm on the keypad.
3 minute Lock Out Feature
After five (5) unsuccessful attempts of an invalid code or fingerprint, RFID Key Tag lock out
mode is activated for 3 minutes.
Smart Etiquette
When entering a pin code on the keypad, the user can open the door lock in silent mode.
Fake PIN Code
Security enhancement to enter any number before or after entering a password to prevent
the PIN code from being exposed.
Internal Forced Lock
It is a security-enhancing function that 'disables' authentication methods such as passwords
and fingerprints from outside when setting up functions indoors.
External Forced Lock
It is a security-enhancing function that an alarm goes off if someone opens door from inside
when setting up functions outside.
Voice Guidance
It guides you through the operation status on how to enable various features & settings- mode
for easier and more convenient use.
Other features and Benefits
•Remote Controller (Optional):
This option may not be available depending on your country or local dealer.
•Network Module/Controller (Optional):
It allows door lock to connect with Home network controller.
•Intrusion/Broken Alarm.
•Low Battery Alarm and Emergency Power Supply.
•User Manual
• Installation Guide
• Screws
• RFID Key Tags X 4
• Remote Controller
• Remote Control
Module
• Bluetooth Module
Palm touch Enter the Code Palm touch Enter the
button
OR
Delete all fingerprint credentials
Delete
PIN CODE
UPIN CODE
U
OR
Registr
-ation
Delete
Visitor Code
OR
OR
PIN CODE
U
PIN CODE
V
Registr
-ation
Delete
Onetime Code Only 1 User, Automatically deleted after use
OR
OR
PIN CODE
U
PIN CODE
O
Only 1 User
PIN CODE
U
PIN CODE
U
Enable
Disable
Automatic Lock
PIN CODE
U
OR
OR
OR
OR
OR
Volume Control
High
Low
Mute
Remote Controller
Set with registration button located on the top of remote controller.
You can press it using a pin like the one shown in the image.
Registr
-ation
Delete
Remote Controller
OR
OR
PIN CODE
U
Button
SET
Registr
-ation
Delete
Home Network Controller
OR
OR
PIN CODE
U
roller
Cont
PIN CODE
U
PIN CODE
U
Up to 5 Users
OR
OR
OR
OR
Registr
-ation
Language Change
Korean
Chinese
English
Taiwanese
PIN CODE
U
PIN CODE
U
Please note following when pairing lock with Yale Access App.
- Depending on product type or FW version, app registration and door lock connection in normal mode may not
be possible, so if registration is not possible, change from normal mode to master mode and try again.
[ App Registration in Master Mode: Master Pin Code-> R (Registration Button)-> 7 -> # ]
- Because Yale Access Bluetooth App is only available in master mode, user code automatically changes to
master code when registering APP in normal mode.
- Please be informed that all registered credentials will be deleted when changing mode or registering and
deleting app.
Registr
-ation
Bluetooth setting (Yale Access app)
PIN CODE
U
Set up a new device in the app
U
PIN CODE
M
PIN CODE
V
PIN CODE
O
PIN CODE
UN
Master Mode : Only a designated person who knows 'Master PIN Code' has authority
to set features.
Normal Mode:
If no user is assigned with master code without a designated person,
anyone who knows ‘User PIN Code’ has authority to set features.
Visitor Code: Users with Visitor Code can only open the door with no access to change
settings.
Onetime Code: The onetime code is used only once for unlocking the door lock and
automatically deleted after usage.
User Slot Number: It should be 2 digits(like ’01’, ‘02’…’99’, ‘00’) and available
in advanced mode.
3
4
5
Enter User RFID Key Tag (Up to 100 Users)
Registr
-ation
RFID Key Tag Up to 100 Users
Touch the panel of finger
print area sensor using
registered fingerprint
for 1 seconds.
Fingerprint
scan completed
Contact registered
RFID Key Tag
Palm touch
for 3sec.
Enter the User PIN Code
then touch the keypad
with your palm
Scan
Fingerprint
OR OR
Touch
RFID Key Tag

1. Front Body (Front Body, installation on the outside of the door)
2. Basic Contents
Basic Contents
5. Front Body
4. Main Body (Main Body, installation on the inside of the door) 7. Setting Menu 9. Normal Mode (Default Mode)
Front Body Main Body Main bracket
Dead Bolt & Strike Plate
Optional Accessories
Mechanical Keys
12. Unlocking Door with Smart Etiquette.
3. Specifications
※Battery life may vary depending on temperature, moisture levels, frequency of use and the quality of battery used.
※Please make sure that all parts are included when purchasing the product.
※Optional products may not be available depending on your country or local dealer.
※Even after a door was locked by the Auto Lock function,
please check again if the door was completely closed and locked.
11. Unlocking Door with Code
14. Locking the door
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds after
the door was closed.
Manual Lock status :
Touch the keypad
in the front body gently
with your palm to lock a door.
9V Emergency
alkaline battery
Emergency Key
6. Main Body
1
Fingerprint Sensor
2
Keypad(10-key)
3
RFID Key Tag reader
4
Dead Bolt Jam Lamp
6
Emergency Power Supply Terminal (Mechanical Key)
5
Low Battery Indicator
7
Emergency Power Supply Terminal (9V Emergency alkaline battery)
Touch the Keypad of the Front Body with your palm to begin
Press button on the Keypad
Press button on the Keypad
Press (Registration) button in every steps to start or
complete the session
Enter User Fingerprint
(Up to 100 Users)
Enter User Code (4 ~ 10 digits)
Enter Master Code (4 ~ 10 digits)
Enter Visitor Code (Only 4 digits)
Enter Onetime Code (Only 4 digits)
User Slot Number should be 2 digits
(like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100". )
Rotation area to add more features
Normal mode is for convenient mode for anyone with user code to change
various settings.
Registr
-ation New
Only 1 User
User Code
PIN CODE
U
OR
Registr
-ation 8times
Fingerprint Up to 100 Users
12 (Registration process)
1Continue / Complete
YDD724A
7
6
1
2
Optional
1
2
3
4
5
6
1
2
Module Accessory Slot (Optional)
3
1.5V AA Alkaline Batteries (4PCS)
4
Thumb turn knob
5
Battery Cover
6
Open / Close button
Registration button
Operating temperature
-15~55˚C (5~131˚F)
100 different RFID Key Tags,
fingerprints, User codes
Up to 100 RFID Key Tags,
fingerprints, User codes
Specifications RemarksParts
Front Body
Fingerprint,
RFID Key Tag,
User code
It lasts a year
if used 10 times a day.
Optional
3EA
4EA 1.5V AA Alkaline batteries
(Operating voltage: 4.5~6V)
Wireless
Optional Remote Controller
Emergency Key
Works for
Main Body
66(W) X 176(H) X 31.5(D), Zinc die-casting
70(W) X 170(H) X 35(D), ALDC
10. Unlocking Door with Fingerprint
13. Open/Close the door from inside
Close Door from Outside
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds
after the door was closed.
Manual Lock status :
Turn manual
thumb turn knob to
close the lock,
Into ‘Close’ marked direction.
Press Open/Close button.
Close Door from Inside
Open/Close button
To open the lock,
turn manual thumb turn knob
from 'Close' direction to
'Open' direction.
Thumb turn knob
5 Sec
5 Sec
8. Product Features
One Touch Fingerprint Access
Secure one Touch Live fingerprint detection for personalized access. Unique Sensor not only
provides high security but faster unlocking experience as well.
Yale Access App
Yale Access gives you the peace of mind of knowing who and what you love is safe - no matter
where you are- just at the touch of your smartphone.
Smart Touchpad – Auto Lock
The door Locks when you touch the palm on the keypad.
3 minute Lock Out Feature
After five (5) unsuccessful attempts of an invalid code or fingerprint, RFID Key Tag lock out
mode is activated for 3 minutes.
Smart Etiquette
When entering a pin code on the keypad, the user can open the door lock in silent mode.
Fake PIN Code
Security enhancement to enter any number before or after entering a password to prevent
the PIN code from being exposed.
Internal Forced Lock
It is a security-enhancing function that 'disables' authentication methods such as passwords
and fingerprints from outside when setting up functions indoors.
External Forced Lock
It is a security-enhancing function that an alarm goes off if someone opens door from inside
when setting up functions outside.
Voice Guidance
It guides you through the operation status on how to enable various features & settings- mode
for easier and more convenient use.
Other features and Benefits
•Remote Controller (Optional):
This option may not be available depending on your country or local dealer.
•Network Module/Controller (Optional):
It allows door lock to connect with Home network controller.
•Intrusion/Broken Alarm.
•Low Battery Alarm and Emergency Power Supply.
•User Manual
• Installation Guide
• Screws
• RFID Key Tags X 4
• Remote Controller
• Remote Control
Module
• Bluetooth Module
Palm touch Enter the Code Palm touch Enter the
button
OR
Delete all fingerprint credentials
Delete
PIN CODE
UPIN CODE
U
OR
Registr
-ation
Delete
Visitor Code
OR
OR
PIN CODE
U
PIN CODE
V
Registr
-ation
Delete
Onetime Code Only 1 User, Automatically deleted after use
OR
OR
PIN CODE
U
PIN CODE
O
Only 1 User
PIN CODE
U
PIN CODE
U
Enable
Disable
Automatic Lock
PIN CODE
U
OR
OR
OR
OR
OR
Volume Control
High
Low
Mute
Remote Controller
Set with registration button located on the top of remote controller.
You can press it using a pin like the one shown in the image.
Registr
-ation
Delete
Remote Controller
OR
OR
PIN CODE
U
Button
SET
Registr
-ation
Delete
Home Network Controller
OR
OR
PIN CODE
U
roller
Cont
PIN CODE
U
PIN CODE
U
Up to 5 Users
OR
OR
OR
OR
Registr
-ation
Language Change
Korean
Chinese
English
Taiwanese
PIN CODE
U
PIN CODE
U
Please note following when pairing lock with Yale Access App.
- Depending on product type or FW version, app registration and door lock connection in normal mode may not
be possible, so if registration is not possible, change from normal mode to master mode and try again.
[ App Registration in Master Mode: Master Pin Code-> R (Registration Button)-> 7 -> # ]
- Because Yale Access Bluetooth App is only available in master mode, user code automatically changes to
master code when registering APP in normal mode.
- Please be informed that all registered credentials will be deleted when changing mode or registering and
deleting app.
Registr
-ation
Bluetooth setting (Yale Access app)
PIN CODE
U
Set up a new device in the app
U
PIN CODE
M
PIN CODE
V
PIN CODE
O
PIN CODE
UN
Master Mode : Only a designated person who knows 'Master PIN Code' has authority
to set features.
Normal Mode:
If no user is assigned with master code without a designated person,
anyone who knows ‘User PIN Code’ has authority to set features.
Visitor Code: Users with Visitor Code can only open the door with no access to change
settings.
Onetime Code: The onetime code is used only once for unlocking the door lock and
automatically deleted after usage.
User Slot Number: It should be 2 digits(like ’01’, ‘02’…’99’, ‘00’) and available
in advanced mode.
3
4
5
Enter User RFID Key Tag (Up to 100 Users)
Registr
-ation
RFID Key Tag Up to 100 Users
Touch the panel of finger
print area sensor using
registered fingerprint
for 1 seconds.
Fingerprint
scan completed
Contact registered
RFID Key Tag
Palm touch
for 3sec.
Enter the User PIN Code
then touch the keypad
with your palm
Scan
Fingerprint
OR OR
Touch
RFID Key Tag

1. Front Body (Front Body, installation on the outside of the door)
2. Basic Contents
Basic Contents
5. Front Body
4. Main Body (Main Body, installation on the inside of the door) 7. Setting Menu 9. Normal Mode (Default Mode)
Front Body Main Body Main bracket
Dead Bolt & Strike Plate
Optional Accessories
Mechanical Keys
12. Unlocking Door with Smart Etiquette.
3. Specifications
※Battery life may vary depending on temperature, moisture levels, frequency of use and the quality of battery used.
※Please make sure that all parts are included when purchasing the product.
※Optional products may not be available depending on your country or local dealer.
※Even after a door was locked by the Auto Lock function,
please check again if the door was completely closed and locked.
11. Unlocking Door with Code
14. Locking the door
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds after
the door was closed.
Manual Lock status :
Touch the keypad
in the front body gently
with your palm to lock a door.
9V Emergency
alkaline battery
Emergency Key
6. Main Body
1
Fingerprint Sensor
2
Keypad(10-key)
3
RFID Key Tag reader
4
Dead Bolt Jam Lamp
6
Emergency Power Supply Terminal (Mechanical Key)
5
Low Battery Indicator
7
Emergency Power Supply Terminal (9V Emergency alkaline battery)
Touch the Keypad of the Front Body with your palm to begin
Press button on the Keypad
Press button on the Keypad
Press (Registration) button in every steps to start or
complete the session
Enter User Fingerprint
(Up to 100 Users)
Enter User Code (4 ~ 10 digits)
Enter Master Code (4 ~ 10 digits)
Enter Visitor Code (Only 4 digits)
Enter Onetime Code (Only 4 digits)
User Slot Number should be 2 digits
(like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100". )
Rotation area to add more features
Normal mode is for convenient mode for anyone with user code to change
various settings.
Registr
-ation New
Only 1 User
User Code
PIN CODE
U
OR
Registr
-ation 8times
Fingerprint Up to 100 Users
12 (Registration process)
1Continue / Complete
YDD724A
7
6
1
2
Optional
1
2
3
4
5
6
1
2
Module Accessory Slot (Optional)
3
1.5V AA Alkaline Batteries (4PCS)
4
Thumb turn knob
5
Battery Cover
6
Open / Close button
Registration button
Operating temperature
-15~55˚C (5~131˚F)
100 different RFID Key Tags,
fingerprints, User codes
Up to 100 RFID Key Tags,
fingerprints, User codes
Specifications RemarksParts
Front Body
Fingerprint,
RFID Key Tag,
User code
It lasts a year
if used 10 times a day.
Optional
3EA
4EA 1.5V AA Alkaline batteries
(Operating voltage: 4.5~6V)
Wireless
Optional Remote Controller
Emergency Key
Works for
Main Body
66(W) X 176(H) X 31.5(D), Zinc die-casting
70(W) X 170(H) X 35(D), ALDC
10. Unlocking Door with Fingerprint
13. Open/Close the door from inside
Close Door from Outside
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds
after the door was closed.
Manual Lock status :
Turn manual
thumb turn knob to
close the lock,
Into ‘Close’ marked direction.
Press Open/Close button.
Close Door from Inside
Open/Close button
To open the lock,
turn manual thumb turn knob
from 'Close' direction to
'Open' direction.
Thumb turn knob
5 Sec
5 Sec
8. Product Features
One Touch Fingerprint Access
Secure one Touch Live fingerprint detection for personalized access. Unique Sensor not only
provides high security but faster unlocking experience as well.
Yale Access App
Yale Access gives you the peace of mind of knowing who and what you love is safe - no matter
where you are- just at the touch of your smartphone.
Smart Touchpad – Auto Lock
The door Locks when you touch the palm on the keypad.
3 minute Lock Out Feature
After five (5) unsuccessful attempts of an invalid code or fingerprint, RFID Key Tag lock out
mode is activated for 3 minutes.
Smart Etiquette
When entering a pin code on the keypad, the user can open the door lock in silent mode.
Fake PIN Code
Security enhancement to enter any number before or after entering a password to prevent
the PIN code from being exposed.
Internal Forced Lock
It is a security-enhancing function that 'disables' authentication methods such as passwords
and fingerprints from outside when setting up functions indoors.
External Forced Lock
It is a security-enhancing function that an alarm goes off if someone opens door from inside
when setting up functions outside.
Voice Guidance
It guides you through the operation status on how to enable various features & settings- mode
for easier and more convenient use.
Other features and Benefits
•Remote Controller (Optional):
This option may not be available depending on your country or local dealer.
•Network Module/Controller (Optional):
It allows door lock to connect with Home network controller.
•Intrusion/Broken Alarm.
•Low Battery Alarm and Emergency Power Supply.
•User Manual
• Installation Guide
• Screws
• RFID Key Tags X 4
• Remote Controller
• Remote Control
Module
• Bluetooth Module
Palm touch Enter the Code Palm touch Enter the
button
OR
Delete all fingerprint credentials
Delete
PIN CODE
UPIN CODE
U
OR
Registr
-ation
Delete
Visitor Code
OR
OR
PIN CODE
U
PIN CODE
V
Registr
-ation
Delete
Onetime Code Only 1 User, Automatically deleted after use
OR
OR
PIN CODE
U
PIN CODE
O
Only 1 User
PIN CODE
U
PIN CODE
U
Enable
Disable
Automatic Lock
PIN CODE
U
OR
OR
OR
OR
OR
Volume Control
High
Low
Mute
Remote Controller
Set with registration button located on the top of remote controller.
You can press it using a pin like the one shown in the image.
Registr
-ation
Delete
Remote Controller
OR
OR
PIN CODE
U
Button
SET
Registr
-ation
Delete
Home Network Controller
OR
OR
PIN CODE
U
roller
Cont
PIN CODE
U
PIN CODE
U
Up to 5 Users
OR
OR
OR
OR
Registr
-ation
Language Change
Korean
Chinese
English
Taiwanese
PIN CODE
U
PIN CODE
U
Please note following when pairing lock with Yale Access App.
- Depending on product type or FW version, app registration and door lock connection in normal mode may not
be possible, so if registration is not possible, change from normal mode to master mode and try again.
[ App Registration in Master Mode: Master Pin Code-> R (Registration Button)-> 7 -> # ]
- Because Yale Access Bluetooth App is only available in master mode, user code automatically changes to
master code when registering APP in normal mode.
- Please be informed that all registered credentials will be deleted when changing mode or registering and
deleting app.
Registr
-ation
Bluetooth setting (Yale Access app)
PIN CODE
U
Set up a new device in the app
U
PIN CODE
M
PIN CODE
V
PIN CODE
O
PIN CODE
UN
Master Mode : Only a designated person who knows 'Master PIN Code' has authority
to set features.
Normal Mode:
If no user is assigned with master code without a designated person,
anyone who knows ‘User PIN Code’ has authority to set features.
Visitor Code: Users with Visitor Code can only open the door with no access to change
settings.
Onetime Code: The onetime code is used only once for unlocking the door lock and
automatically deleted after usage.
User Slot Number: It should be 2 digits(like ’01’, ‘02’…’99’, ‘00’) and available
in advanced mode.
3
4
5
Enter User RFID Key Tag (Up to 100 Users)
Registr
-ation
RFID Key Tag Up to 100 Users
Touch the panel of finger
print area sensor using
registered fingerprint
for 1 seconds.
Fingerprint
scan completed
Contact registered
RFID Key Tag
Palm touch
for 3sec.
Enter the User PIN Code
then touch the keypad
with your palm
Scan
Fingerprint
OR OR
Touch
RFID Key Tag

1. Front Body (Front Body, installation on the outside of the door)
2. Basic Contents
Basic Contents
5. Front Body
4. Main Body (Main Body, installation on the inside of the door) 7. Setting Menu 9. Normal Mode (Default Mode)
Front Body Main Body Main bracket
Dead Bolt & Strike Plate
Optional Accessories
Mechanical Keys
12. Unlocking Door with Smart Etiquette.
3. Specifications
※Battery life may vary depending on temperature, moisture levels, frequency of use and the quality of battery used.
※Please make sure that all parts are included when purchasing the product.
※Optional products may not be available depending on your country or local dealer.
※Even after a door was locked by the Auto Lock function,
please check again if the door was completely closed and locked.
11. Unlocking Door with Code
14. Locking the door
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds after
the door was closed.
Manual Lock status :
Touch the keypad
in the front body gently
with your palm to lock a door.
9V Emergency
alkaline battery
Emergency Key
6. Main Body
1
Fingerprint Sensor
2
Keypad(10-key)
3
RFID Key Tag reader
4
Dead Bolt Jam Lamp
6
Emergency Power Supply Terminal (Mechanical Key)
5
Low Battery Indicator
7
Emergency Power Supply Terminal (9V Emergency alkaline battery)
Touch the Keypad of the Front Body with your palm to begin
Press button on the Keypad
Press button on the Keypad
Press (Registration) button in every steps to start or
complete the session
Enter User Fingerprint
(Up to 100 Users)
Enter User Code (4 ~ 10 digits)
Enter Master Code (4 ~ 10 digits)
Enter Visitor Code (Only 4 digits)
Enter Onetime Code (Only 4 digits)
User Slot Number should be 2 digits
(like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100". )
Rotation area to add more features
Normal mode is for convenient mode for anyone with user code to change
various settings.
Registr
-ation New
Only 1 User
User Code
PIN CODE
U
OR
Registr
-ation 8times
Fingerprint Up to 100 Users
12 (Registration process)
1Continue / Complete
YDD724A
7
6
1
2
Optional
1
2
3
4
5
6
1
2
Module Accessory Slot (Optional)
3
1.5V AA Alkaline Batteries (4PCS)
4
Thumb turn knob
5
Battery Cover
6
Open / Close button
Registration button
Operating temperature
-15~55˚C (5~131˚F)
100 different RFID Key Tags,
fingerprints, User codes
Up to 100 RFID Key Tags,
fingerprints, User codes
Specifications RemarksParts
Front Body
Fingerprint,
RFID Key Tag,
User code
It lasts a year
if used 10 times a day.
Optional
3EA
4EA 1.5V AA Alkaline batteries
(Operating voltage: 4.5~6V)
Wireless
Optional Remote Controller
Emergency Key
Works for
Main Body
66(W) X 176(H) X 31.5(D), Zinc die-casting
70(W) X 170(H) X 35(D), ALDC
10. Unlocking Door with Fingerprint
13. Open/Close the door from inside
Close Door from Outside
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds
after the door was closed.
Manual Lock status :
Turn manual
thumb turn knob to
close the lock,
Into ‘Close’ marked direction.
Press Open/Close button.
Close Door from Inside
Open/Close button
To open the lock,
turn manual thumb turn knob
from 'Close' direction to
'Open' direction.
Thumb turn knob
5 Sec
5 Sec
8. Product Features
One Touch Fingerprint Access
Secure one Touch Live fingerprint detection for personalized access. Unique Sensor not only
provides high security but faster unlocking experience as well.
Yale Access App
Yale Access gives you the peace of mind of knowing who and what you love is safe - no matter
where you are- just at the touch of your smartphone.
Smart Touchpad – Auto Lock
The door Locks when you touch the palm on the keypad.
3 minute Lock Out Feature
After five (5) unsuccessful attempts of an invalid code or fingerprint, RFID Key Tag lock out
mode is activated for 3 minutes.
Smart Etiquette
When entering a pin code on the keypad, the user can open the door lock in silent mode.
Fake PIN Code
Security enhancement to enter any number before or after entering a password to prevent
the PIN code from being exposed.
Internal Forced Lock
It is a security-enhancing function that 'disables' authentication methods such as passwords
and fingerprints from outside when setting up functions indoors.
External Forced Lock
It is a security-enhancing function that an alarm goes off if someone opens door from inside
when setting up functions outside.
Voice Guidance
It guides you through the operation status on how to enable various features & settings- mode
for easier and more convenient use.
Other features and Benefits
•Remote Controller (Optional):
This option may not be available depending on your country or local dealer.
•Network Module/Controller (Optional):
It allows door lock to connect with Home network controller.
•Intrusion/Broken Alarm.
•Low Battery Alarm and Emergency Power Supply.
•User Manual
• Installation Guide
• Screws
• RFID Key Tags X 4
• Remote Controller
• Remote Control
Module
• Bluetooth Module
Palm touch Enter the Code Palm touch Enter the
button
OR
Delete all fingerprint credentials
Delete
PIN CODE
UPIN CODE
U
OR
Registr
-ation
Delete
Visitor Code
OR
OR
PIN CODE
U
PIN CODE
V
Registr
-ation
Delete
Onetime Code Only 1 User, Automatically deleted after use
OR
OR
PIN CODE
U
PIN CODE
O
Only 1 User
PIN CODE
U
PIN CODE
U
Enable
Disable
Automatic Lock
PIN CODE
U
OR
OR
OR
OR
OR
Volume Control
High
Low
Mute
Remote Controller
Set with registration button located on the top of remote controller.
You can press it using a pin like the one shown in the image.
Registr
-ation
Delete
Remote Controller
OR
OR
PIN CODE
U
Button
SET
Registr
-ation
Delete
Home Network Controller
OR
OR
PIN CODE
U
roller
Cont
PIN CODE
U
PIN CODE
U
Up to 5 Users
OR
OR
OR
OR
Registr
-ation
Language Change
Korean
Chinese
English
Taiwanese
PIN CODE
U
PIN CODE
U
Please note following when pairing lock with Yale Access App.
- Depending on product type or FW version, app registration and door lock connection in normal mode may not
be possible, so if registration is not possible, change from normal mode to master mode and try again.
[ App Registration in Master Mode: Master Pin Code-> R (Registration Button)-> 7 -> # ]
- Because Yale Access Bluetooth App is only available in master mode, user code automatically changes to
master code when registering APP in normal mode.
- Please be informed that all registered credentials will be deleted when changing mode or registering and
deleting app.
Registr
-ation
Bluetooth setting (Yale Access app)
PIN CODE
U
Set up a new device in the app
U
PIN CODE
M
PIN CODE
V
PIN CODE
O
PIN CODE
UN
Master Mode : Only a designated person who knows 'Master PIN Code' has authority
to set features.
Normal Mode:
If no user is assigned with master code without a designated person,
anyone who knows ‘User PIN Code’ has authority to set features.
Visitor Code: Users with Visitor Code can only open the door with no access to change
settings.
Onetime Code: The onetime code is used only once for unlocking the door lock and
automatically deleted after usage.
User Slot Number: It should be 2 digits(like ’01’, ‘02’…’99’, ‘00’) and available
in advanced mode.
3
4
5
Enter User RFID Key Tag (Up to 100 Users)
Registr
-ation
RFID Key Tag Up to 100 Users
Touch the panel of finger
print area sensor using
registered fingerprint
for 1 seconds.
Fingerprint
scan completed
Contact registered
RFID Key Tag
Palm touch
for 3sec.
Enter the User PIN Code
then touch the keypad
with your palm
Scan
Fingerprint
OR OR
Touch
RFID Key Tag

1. Front Body (Front Body, installation on the outside of the door)
2. Basic Contents
Basic Contents
5. Front Body
4. Main Body (Main Body, installation on the inside of the door) 7. Setting Menu 9. Normal Mode (Default Mode)
Front Body Main Body Main bracket
Dead Bolt & Strike Plate
Optional Accessories
Mechanical Keys
12. Unlocking Door with Smart Etiquette.
3. Specifications
※Battery life may vary depending on temperature, moisture levels, frequency of use and the quality of battery used.
※Please make sure that all parts are included when purchasing the product.
※Optional products may not be available depending on your country or local dealer.
※Even after a door was locked by the Auto Lock function,
please check again if the door was completely closed and locked.
11. Unlocking Door with Code
14. Locking the door
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds after
the door was closed.
Manual Lock status :
Touch the keypad
in the front body gently
with your palm to lock a door.
9V Emergency
alkaline battery
Emergency Key
6. Main Body
1
Fingerprint Sensor
2
Keypad(10-key)
3
RFID Key Tag reader
4
Dead Bolt Jam Lamp
6
Emergency Power Supply Terminal (Mechanical Key)
5
Low Battery Indicator
7
Emergency Power Supply Terminal (9V Emergency alkaline battery)
Touch the Keypad of the Front Body with your palm to begin
Press button on the Keypad
Press button on the Keypad
Press (Registration) button in every steps to start or
complete the session
Enter User Fingerprint
(Up to 100 Users)
Enter User Code (4 ~ 10 digits)
Enter Master Code (4 ~ 10 digits)
Enter Visitor Code (Only 4 digits)
Enter Onetime Code (Only 4 digits)
User Slot Number should be 2 digits
(like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100". )
Rotation area to add more features
Normal mode is for convenient mode for anyone with user code to change
various settings.
Registr
-ation New
Only 1 User
User Code
PIN CODE
U
OR
Registr
-ation 8times
Fingerprint Up to 100 Users
12 (Registration process)
1Continue / Complete
YDD724A
7
6
1
2
Optional
1
2
3
4
5
6
1
2
Module Accessory Slot (Optional)
3
1.5V AA Alkaline Batteries (4PCS)
4
Thumb turn knob
5
Battery Cover
6
Open / Close button
Registration button
Operating temperature
-15~55˚C (5~131˚F)
100 different RFID Key Tags,
fingerprints, User codes
Up to 100 RFID Key Tags,
fingerprints, User codes
Specifications RemarksParts
Front Body
Fingerprint,
RFID Key Tag,
User code
It lasts a year
if used 10 times a day.
Optional
3EA
4EA 1.5V AA Alkaline batteries
(Operating voltage: 4.5~6V)
Wireless
Optional Remote Controller
Emergency Key
Works for
Main Body
66(W) X 176(H) X 31.5(D), Zinc die-casting
70(W) X 170(H) X 35(D), ALDC
10. Unlocking Door with Fingerprint
13. Open/Close the door from inside
Close Door from Outside
Auto Lock status :
The built-in Auto Lock sensor
automatically locks a door
within 5 seconds
after the door was closed.
Manual Lock status :
Turn manual
thumb turn knob to
close the lock,
Into ‘Close’ marked direction.
Press Open/Close button.
Close Door from Inside
Open/Close button
To open the lock,
turn manual thumb turn knob
from 'Close' direction to
'Open' direction.
Thumb turn knob
5 Sec
5 Sec
8. Product Features
One Touch Fingerprint Access
Secure one Touch Live fingerprint detection for personalized access. Unique Sensor not only
provides high security but faster unlocking experience as well.
Yale Access App
Yale Access gives you the peace of mind of knowing who and what you love is safe - no matter
where you are- just at the touch of your smartphone.
Smart Touchpad – Auto Lock
The door Locks when you touch the palm on the keypad.
3 minute Lock Out Feature
After five (5) unsuccessful attempts of an invalid code or fingerprint, RFID Key Tag lock out
mode is activated for 3 minutes.
Smart Etiquette
When entering a pin code on the keypad, the user can open the door lock in silent mode.
Fake PIN Code
Security enhancement to enter any number before or after entering a password to prevent
the PIN code from being exposed.
Internal Forced Lock
It is a security-enhancing function that 'disables' authentication methods such as passwords
and fingerprints from outside when setting up functions indoors.
External Forced Lock
It is a security-enhancing function that an alarm goes off if someone opens door from inside
when setting up functions outside.
Voice Guidance
It guides you through the operation status on how to enable various features & settings- mode
for easier and more convenient use.
Other features and Benefits
•Remote Controller (Optional):
This option may not be available depending on your country or local dealer.
•Network Module/Controller (Optional):
It allows door lock to connect with Home network controller.
•Intrusion/Broken Alarm.
•Low Battery Alarm and Emergency Power Supply.
•User Manual
• Installation Guide
• Screws
• RFID Key Tags X 4
• Remote Controller
• Remote Control
Module
• Bluetooth Module
Palm touch Enter the Code Palm touch Enter the
button
OR
Delete all fingerprint credentials
Delete
PIN CODE
UPIN CODE
U
OR
Registr
-ation
Delete
Visitor Code
OR
OR
PIN CODE
U
PIN CODE
V
Registr
-ation
Delete
Onetime Code Only 1 User, Automatically deleted after use
OR
OR
PIN CODE
U
PIN CODE
O
Only 1 User
PIN CODE
U
PIN CODE
U
Enable
Disable
Automatic Lock
PIN CODE
U
OR
OR
OR
OR
OR
Volume Control
High
Low
Mute
Remote Controller
Set with registration button located on the top of remote controller.
You can press it using a pin like the one shown in the image.
Registr
-ation
Delete
Remote Controller
OR
OR
PIN CODE
U
Button
SET
Registr
-ation
Delete
Home Network Controller
OR
OR
PIN CODE
U
roller
Cont
PIN CODE
U
PIN CODE
U
Up to 5 Users
OR
OR
OR
OR
Registr
-ation
Language Change
Korean
Chinese
English
Taiwanese
PIN CODE
U
PIN CODE
U
Please note following when pairing lock with Yale Access App.
- Depending on product type or FW version, app registration and door lock connection in normal mode may not
be possible, so if registration is not possible, change from normal mode to master mode and try again.
[ App Registration in Master Mode: Master Pin Code-> R (Registration Button)-> 7 -> # ]
- Because Yale Access Bluetooth App is only available in master mode, user code automatically changes to
master code when registering APP in normal mode.
- Please be informed that all registered credentials will be deleted when changing mode or registering and
deleting app.
Registr
-ation
Bluetooth setting (Yale Access app)
PIN CODE
U
Set up a new device in the app
U
PIN CODE
M
PIN CODE
V
PIN CODE
O
PIN CODE
UN
Master Mode : Only a designated person who knows 'Master PIN Code' has authority
to set features.
Normal Mode:
If no user is assigned with master code without a designated person,
anyone who knows ‘User PIN Code’ has authority to set features.
Visitor Code: Users with Visitor Code can only open the door with no access to change
settings.
Onetime Code: The onetime code is used only once for unlocking the door lock and
automatically deleted after usage.
User Slot Number: It should be 2 digits(like ’01’, ‘02’…’99’, ‘00’) and available
in advanced mode.
3
4
5
Enter User RFID Key Tag (Up to 100 Users)
Registr
-ation
RFID Key Tag Up to 100 Users
Touch the panel of finger
print area sensor using
registered fingerprint
for 1 seconds.
Fingerprint
scan completed
Contact registered
RFID Key Tag
Palm touch
for 3sec.
Enter the User PIN Code
then touch the keypad
with your palm
Scan
Fingerprint
OR OR
Touch
RFID Key Tag

16. Internal Forced Lock
15. External Forced Lock
User Guide
RFID Key Tag / Fingerprint / PIN Code / Key
YDD724A
23. Master Mode
17. Alarm
18. 3 Minute Lock Out
19. Unlocking Door with Fake Code
Intrusion Alarm : The alarm goes off when someone forces the door open.
For example, In case of an intrusion by opening a gap
in the door while the door is locked.
Broken Alarm(Breakage Alarm) : The alarm goes off when the front part is
completely separated from the main set. For example,
forced removal of external product (front body).
Turn off Alarm
There is no limitation for
digits of Fake Pin Code.
Disable 3-minute Lock Out
All access mode from the external side are disabled for 3 minutes to deter
unauthorized access.
Press the Open/Close button.
Open the door with mechanical key.
Press button.
Enter the registered User Code.
Scan the registered fingerprint.
Press and hold the O/C Button for 5seconds.
Touch the registered RFID Key Tag.
20. Power supply
21. Emergency power supply for discharged batteries
One-on-one real life size
1.5V(LR6) Alkaline AA Battery
It may sustain 1 year if used 10 times
a day. (Users are advised to use
authentic Alkaline batteries.)
* Kindly dispose used batteries.
•
Do not install the digital door lock in an outdoor environment.
•
Do not attempt to disassemble the digital door lock by your self.
By doing so, you may get an electronic shock and damage the product.
•
Do not use force with a tool onto the product.
•
Make sure to lock the door tight when you go out.
•
Do not use water and any type of solvent to clean the product such as
gasoline or benzene as they can cause damage to electronic circuit,
deterioration and or paint peel-off.
•
It is recommended to change User Code on a regular basis.
•
In manual lock mode, make sure to double check whether the door is
securely locked.
•
When External Forced lock is set and unlock the door, the alarm will be
activated.
•
Do not use rechargeable batteries. Only alkaline batteries are recommended.
•
Make sure to follow the above instructions to avoid any injuries.
•
It cannot be guaranteed in a special conditions & environment such as
water condensation, seaside.
•
Warranty will not cover- exposure to dampness, excessive heat,
excessive humidity and other extreme environmental conditions,
corrosion, damage beyond repair, rusting, unauthorised modifications,
unauthorised repairs, neglect, accident, alteration, acts of God,
spillage of liquid or food particles.
Master mode is a mode in which only the administrator can set the door lock and provide
access to other users. 100 users passwords, 100 users RFID key tags,100 users fingerprint and
individual registration and deletion of one-time passwords enable efficient management of visitors.
Change
Mode New Again
Switch to master mode (from normal mode)
PIN CODE
UPIN CODE MPIN CODE M
Change
Mode New Again
Switch to normal mode (from master mode)
PIN CODE
UPIN CODE U
OR
Registr
-ation New Again
Master Pin Code Change
PIN CODE
M
PIN CODE
M
PIN CODE
M
Delete
OR
Registr
-ation
User Code
PIN CODE
U
UN
OR
UN
PIN CODE
M
Up to 100 Users
Only 1 User
Delete
OR
Registr
-ation
Fingerprint
UN
OR
UN
PIN CODE
M
Up to 100 Users
Delete
Registr
-ation
Onetime Code
OR
OR
PIN CODE
M
PIN CODE
M
PIN CODE
O
Only 1 User, Automatically deleted after use
Langu
-age
Setting
Language Change
OR
OR
OR
OR
OR
Delete
Delete all credentials
PIN CODE
M
PIN CODE
M
PIN CODE
M
Registr
-ation
Bluetooth Setting (Yale Access App)
PIN CODE
M
Delete
Registr
-ation
Remote Controller
OR
OR
PIN CODE
M
Up to 5 Users
UN
UN
Button
SET
Delete
Registr
-ation
Home Network Controller
OR
OR
PIN CODE
Mroller
Cont
PIN CODE
M
PIN CODE
M
Korean
Chinese
English
Taiwanese
8times
Set up a new device in the app
14 (Registration process)
1
High
Low
Mute
Volume Control
PIN CODE
M
OR
OR
OR
Disable
Enable
Automatic Lock
PIN CODE
M
Continue / Complete
Enable External Forced Lock : Fingerprint
Scan with registered fingerprint and hold the fingerprint area
until you hear 3 beep sounds.
Disable External Forced Lock
When the door is unlocked from outside based upon proper
authentication, the External forced lock will be released.
Palm touch Enter the
User PIN Code
Enter the
button for 5 Sec.
Enable External Forced Lock : User Code
※If you try to open a door with the manual thumb turn knob from inside when the Outside Forced Lock is set,
the alarm goes off.
※If the Inside Forced Lock is set, any attempt to open a door from outside whether it’s be a Fingerprint or
code won’t work.
Press Open/Close button
for 3 seconds until
you hear “pik” beep.
Method 1 :
Press Open/Close
button for 3 seconds
until you hear
“pik” beep.
Method 2 :
Turn manual
thumb turn knob.
Setting
‘ 3 ’
Seconds
Release
‘ 3 ’
Seconds
Turn it
OR
OR
ISL-1857-00-046
PLEASE READ INSTRUCTIONS BEFORE USE.
The functions and design of this product can be changed
without prior notice for performance and quality improvement.
Packaging of this product can be recycled.
User Slot Number should be 2 digits.
like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100".
※
22. Code Chart
Duplicate if necessary
PIN Code Management(Up to 100 Users.)
Do not install the digital door
lock in an outdoor environment.
24. Important notes
Do not attempt to disassemble
the digital door lock by yourself.
Do not spray water directly
or wipe with chemicals such as
benzene, gasoline or alcohol.
Do not use force with a tool
onto the product.
When using, remember that
someone else can see the
password.
Make sure the door is closed
properly when going out.
25. Safety and Warning
※Voice guidance : Voice guidance features assist in easy navigation through various features.
※All registered passwords and other credentials will be deleted when mode is changed.
※Please install(register) the network module when you want to use a remote control or home network.
Part of ASSA ABLOY
You must replace all 4 batteries in the following cases:
* The Low Battery LED on keypad flickers red.
* When low battery notification message is played.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE NATIONAL CODE OR RECYCLING PROGRAM.
Palm touch Palm touchEnter the user code
and fake code
Enter the Fake Code
and User code
OR
Enable External Forced Lock : RFID Key Tag
Contact RFID key tag on [RFID key tag reader] for 5 sec. until you
hear 3 beeps.
※In case of discharged batteries, please use 9V battery to supply power
Palm
touch
OR OR
Contact 9V
battery
Enter the User Code
and Plam touch
Contact
RFID Key Tag
Scan
fingerprint
Delete
OR
Registr
-ation
RFID Key Tag
UN
OR
UN
PIN CODE
M
Up to 100 Users

16. Internal Forced Lock
15. External Forced Lock
User Guide
RFID Key Tag / Fingerprint / PIN Code / Key
YDD724A
23. Master Mode
17. Alarm
18. 3 Minute Lock Out
19. Unlocking Door with Fake Code
Intrusion Alarm : The alarm goes off when someone forces the door open.
For example, In case of an intrusion by opening a gap
in the door while the door is locked.
Broken Alarm(Breakage Alarm) : The alarm goes off when the front part is
completely separated from the main set. For example,
forced removal of external product (front body).
Turn off Alarm
There is no limitation for
digits of Fake Pin Code.
Disable 3-minute Lock Out
All access mode from the external side are disabled for 3 minutes to deter
unauthorized access.
Press the Open/Close button.
Open the door with mechanical key.
Press button.
Enter the registered User Code.
Scan the registered fingerprint.
Press and hold the O/C Button for 5seconds.
Touch the registered RFID Key Tag.
20. Power supply
21. Emergency power supply for discharged batteries
One-on-one real life size
1.5V(LR6) Alkaline AA Battery
It may sustain 1 year if used 10 times
a day. (Users are advised to use
authentic Alkaline batteries.)
* Kindly dispose used batteries.
•
Do not install the digital door lock in an outdoor environment.
•
Do not attempt to disassemble the digital door lock by your self.
By doing so, you may get an electronic shock and damage the product.
•
Do not use force with a tool onto the product.
•
Make sure to lock the door tight when you go out.
•
Do not use water and any type of solvent to clean the product such as
gasoline or benzene as they can cause damage to electronic circuit,
deterioration and or paint peel-off.
•
It is recommended to change User Code on a regular basis.
•
In manual lock mode, make sure to double check whether the door is
securely locked.
•
When External Forced lock is set and unlock the door, the alarm will be
activated.
•
Do not use rechargeable batteries. Only alkaline batteries are recommended.
•
Make sure to follow the above instructions to avoid any injuries.
•
It cannot be guaranteed in a special conditions & environment such as
water condensation, seaside.
•
Warranty will not cover- exposure to dampness, excessive heat,
excessive humidity and other extreme environmental conditions,
corrosion, damage beyond repair, rusting, unauthorised modifications,
unauthorised repairs, neglect, accident, alteration, acts of God,
spillage of liquid or food particles.
Master mode is a mode in which only the administrator can set the door lock and provide
access to other users. 100 users passwords, 100 users RFID key tags,100 users fingerprint and
individual registration and deletion of one-time passwords enable efficient management of visitors.
Change
Mode New Again
Switch to master mode (from normal mode)
PIN CODE
UPIN CODE MPIN CODE M
Change
Mode New Again
Switch to normal mode (from master mode)
PIN CODE
UPIN CODE U
OR
Registr
-ation New Again
Master Pin Code Change
PIN CODE
M
PIN CODE
M
PIN CODE
M
Delete
OR
Registr
-ation
User Code
PIN CODE
U
UN
OR
UN
PIN CODE
M
Up to 100 Users
Only 1 User
Delete
OR
Registr
-ation
Fingerprint
UN
OR
UN
PIN CODE
M
Up to 100 Users
Delete
Registr
-ation
Onetime Code
OR
OR
PIN CODE
M
PIN CODE
M
PIN CODE
O
Only 1 User, Automatically deleted after use
Langu
-age
Setting
Language Change
OR
OR
OR
OR
OR
Delete
Delete all credentials
PIN CODE
M
PIN CODE
M
PIN CODE
M
Registr
-ation
Bluetooth Setting (Yale Access App)
PIN CODE
M
Delete
Registr
-ation
Remote Controller
OR
OR
PIN CODE
M
Up to 5 Users
UN
UN
Button
SET
Delete
Registr
-ation
Home Network Controller
OR
OR
PIN CODE
Mroller
Cont
PIN CODE
M
PIN CODE
M
Korean
Chinese
English
Taiwanese
8times
Set up a new device in the app
14 (Registration process)
1
High
Low
Mute
Volume Control
PIN CODE
M
OR
OR
OR
Disable
Enable
Automatic Lock
PIN CODE
M
Continue / Complete
Enable External Forced Lock : Fingerprint
Scan with registered fingerprint and hold the fingerprint area
until you hear 3 beep sounds.
Disable External Forced Lock
When the door is unlocked from outside based upon proper
authentication, the External forced lock will be released.
Palm touch Enter the
User PIN Code
Enter the
button for 5 Sec.
Enable External Forced Lock : User Code
※If you try to open a door with the manual thumb turn knob from inside when the Outside Forced Lock is set,
the alarm goes off.
※If the Inside Forced Lock is set, any attempt to open a door from outside whether it’s be a Fingerprint or
code won’t work.
Press Open/Close button
for 3 seconds until
you hear “pik” beep.
Method 1 :
Press Open/Close
button for 3 seconds
until you hear
“pik” beep.
Method 2 :
Turn manual
thumb turn knob.
Setting
‘ 3 ’
Seconds
Release
‘ 3 ’
Seconds
Turn it
OR
OR
ISL-1857-00-046
PLEASE READ INSTRUCTIONS BEFORE USE.
The functions and design of this product can be changed
without prior notice for performance and quality improvement.
Packaging of this product can be recycled.
User Slot Number should be 2 digits.
like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100".
※
22. Code Chart
Duplicate if necessary
PIN Code Management(Up to 100 Users.)
Do not install the digital door
lock in an outdoor environment.
24. Important notes
Do not attempt to disassemble
the digital door lock by yourself.
Do not spray water directly
or wipe with chemicals such as
benzene, gasoline or alcohol.
Do not use force with a tool
onto the product.
When using, remember that
someone else can see the
password.
Make sure the door is closed
properly when going out.
25. Safety and Warning
※Voice guidance : Voice guidance features assist in easy navigation through various features.
※All registered passwords and other credentials will be deleted when mode is changed.
※Please install(register) the network module when you want to use a remote control or home network.
Part of ASSA ABLOY
You must replace all 4 batteries in the following cases:
* The Low Battery LED on keypad flickers red.
* When low battery notification message is played.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE NATIONAL CODE OR RECYCLING PROGRAM.
Palm touch Palm touchEnter the user code
and fake code
Enter the Fake Code
and User code
OR
Enable External Forced Lock : RFID Key Tag
Contact RFID key tag on [RFID key tag reader] for 5 sec. until you
hear 3 beeps.
※In case of discharged batteries, please use 9V battery to supply power
Palm
touch
OR OR
Contact 9V
battery
Enter the User Code
and Plam touch
Contact
RFID Key Tag
Scan
fingerprint
Delete
OR
Registr
-ation
RFID Key Tag
UN
OR
UN
PIN CODE
M
Up to 100 Users

16. Internal Forced Lock
15. External Forced Lock
User Guide
RFID Key Tag / Fingerprint / PIN Code / Key
YDD724A
23. Master Mode
17. Alarm
18. 3 Minute Lock Out
19. Unlocking Door with Fake Code
Intrusion Alarm : The alarm goes off when someone forces the door open.
For example, In case of an intrusion by opening a gap
in the door while the door is locked.
Broken Alarm(Breakage Alarm) : The alarm goes off when the front part is
completely separated from the main set. For example,
forced removal of external product (front body).
Turn off Alarm
There is no limitation for
digits of Fake Pin Code.
Disable 3-minute Lock Out
All access mode from the external side are disabled for 3 minutes to deter
unauthorized access.
Press the Open/Close button.
Open the door with mechanical key.
Press button.
Enter the registered User Code.
Scan the registered fingerprint.
Press and hold the O/C Button for 5seconds.
Touch the registered RFID Key Tag.
20. Power supply
21. Emergency power supply for discharged batteries
One-on-one real life size
1.5V(LR6) Alkaline AA Battery
It may sustain 1 year if used 10 times
a day. (Users are advised to use
authentic Alkaline batteries.)
* Kindly dispose used batteries.
•
Do not install the digital door lock in an outdoor environment.
•
Do not attempt to disassemble the digital door lock by your self.
By doing so, you may get an electronic shock and damage the product.
•
Do not use force with a tool onto the product.
•
Make sure to lock the door tight when you go out.
•
Do not use water and any type of solvent to clean the product such as
gasoline or benzene as they can cause damage to electronic circuit,
deterioration and or paint peel-off.
•
It is recommended to change User Code on a regular basis.
•
In manual lock mode, make sure to double check whether the door is
securely locked.
•
When External Forced lock is set and unlock the door, the alarm will be
activated.
•
Do not use rechargeable batteries. Only alkaline batteries are recommended.
•
Make sure to follow the above instructions to avoid any injuries.
•
It cannot be guaranteed in a special conditions & environment such as
water condensation, seaside.
•
Warranty will not cover- exposure to dampness, excessive heat,
excessive humidity and other extreme environmental conditions,
corrosion, damage beyond repair, rusting, unauthorised modifications,
unauthorised repairs, neglect, accident, alteration, acts of God,
spillage of liquid or food particles.
Master mode is a mode in which only the administrator can set the door lock and provide
access to other users. 100 users passwords, 100 users RFID key tags,100 users fingerprint and
individual registration and deletion of one-time passwords enable efficient management of visitors.
Change
Mode New Again
Switch to master mode (from normal mode)
PIN CODE
UPIN CODE MPIN CODE M
Change
Mode New Again
Switch to normal mode (from master mode)
PIN CODE
UPIN CODE U
OR
Registr
-ation New Again
Master Pin Code Change
PIN CODE
M
PIN CODE
M
PIN CODE
M
Delete
OR
Registr
-ation
User Code
PIN CODE
U
UN
OR
UN
PIN CODE
M
Up to 100 Users
Only 1 User
Delete
OR
Registr
-ation
Fingerprint
UN
OR
UN
PIN CODE
M
Up to 100 Users
Delete
Registr
-ation
Onetime Code
OR
OR
PIN CODE
M
PIN CODE
M
PIN CODE
O
Only 1 User, Automatically deleted after use
Langu
-age
Setting
Language Change
OR
OR
OR
OR
OR
Delete
Delete all credentials
PIN CODE
M
PIN CODE
M
PIN CODE
M
Registr
-ation
Bluetooth Setting (Yale Access App)
PIN CODE
M
Delete
Registr
-ation
Remote Controller
OR
OR
PIN CODE
M
Up to 5 Users
UN
UN
Button
SET
Delete
Registr
-ation
Home Network Controller
OR
OR
PIN CODE
Mroller
Cont
PIN CODE
M
PIN CODE
M
Korean
Chinese
English
Taiwanese
8times
Set up a new device in the app
14 (Registration process)
1
High
Low
Mute
Volume Control
PIN CODE
M
OR
OR
OR
Disable
Enable
Automatic Lock
PIN CODE
M
Continue / Complete
Enable External Forced Lock : Fingerprint
Scan with registered fingerprint and hold the fingerprint area
until you hear 3 beep sounds.
Disable External Forced Lock
When the door is unlocked from outside based upon proper
authentication, the External forced lock will be released.
Palm touch Enter the
User PIN Code
Enter the
button for 5 Sec.
Enable External Forced Lock : User Code
※If you try to open a door with the manual thumb turn knob from inside when the Outside Forced Lock is set,
the alarm goes off.
※If the Inside Forced Lock is set, any attempt to open a door from outside whether it’s be a Fingerprint or
code won’t work.
Press Open/Close button
for 3 seconds until
you hear “pik” beep.
Method 1 :
Press Open/Close
button for 3 seconds
until you hear
“pik” beep.
Method 2 :
Turn manual
thumb turn knob.
Setting
‘ 3 ’
Seconds
Release
‘ 3 ’
Seconds
Turn it
OR
OR
ISL-1857-00-046
PLEASE READ INSTRUCTIONS BEFORE USE.
The functions and design of this product can be changed
without prior notice for performance and quality improvement.
Packaging of this product can be recycled.
User Slot Number should be 2 digits.
like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100".
※
22. Code Chart
Duplicate if necessary
PIN Code Management(Up to 100 Users.)
Do not install the digital door
lock in an outdoor environment.
24. Important notes
Do not attempt to disassemble
the digital door lock by yourself.
Do not spray water directly
or wipe with chemicals such as
benzene, gasoline or alcohol.
Do not use force with a tool
onto the product.
When using, remember that
someone else can see the
password.
Make sure the door is closed
properly when going out.
25. Safety and Warning
※Voice guidance : Voice guidance features assist in easy navigation through various features.
※All registered passwords and other credentials will be deleted when mode is changed.
※Please install(register) the network module when you want to use a remote control or home network.
Part of ASSA ABLOY
You must replace all 4 batteries in the following cases:
* The Low Battery LED on keypad flickers red.
* When low battery notification message is played.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE NATIONAL CODE OR RECYCLING PROGRAM.
Palm touch Palm touchEnter the user code
and fake code
Enter the Fake Code
and User code
OR
Enable External Forced Lock : RFID Key Tag
Contact RFID key tag on [RFID key tag reader] for 5 sec. until you
hear 3 beeps.
※In case of discharged batteries, please use 9V battery to supply power
Palm
touch
OR OR
Contact 9V
battery
Enter the User Code
and Plam touch
Contact
RFID Key Tag
Scan
fingerprint
Delete
OR
Registr
-ation
RFID Key Tag
UN
OR
UN
PIN CODE
M
Up to 100 Users

16. Internal Forced Lock
15. External Forced Lock
User Guide
RFID Key Tag / Fingerprint / PIN Code / Key
YDD724A
23. Master Mode
17. Alarm
18. 3 Minute Lock Out
19. Unlocking Door with Fake Code
Intrusion Alarm : The alarm goes off when someone forces the door open.
For example, In case of an intrusion by opening a gap
in the door while the door is locked.
Broken Alarm(Breakage Alarm) : The alarm goes off when the front part is
completely separated from the main set. For example,
forced removal of external product (front body).
Turn off Alarm
There is no limitation for
digits of Fake Pin Code.
Disable 3-minute Lock Out
All access mode from the external side are disabled for 3 minutes to deter
unauthorized access.
Press the Open/Close button.
Open the door with mechanical key.
Press button.
Enter the registered User Code.
Scan the registered fingerprint.
Press and hold the O/C Button for 5seconds.
Touch the registered RFID Key Tag.
20. Power supply
21. Emergency power supply for discharged batteries
One-on-one real life size
1.5V(LR6) Alkaline AA Battery
It may sustain 1 year if used 10 times
a day. (Users are advised to use
authentic Alkaline batteries.)
* Kindly dispose used batteries.
•
Do not install the digital door lock in an outdoor environment.
•
Do not attempt to disassemble the digital door lock by your self.
By doing so, you may get an electronic shock and damage the product.
•
Do not use force with a tool onto the product.
•
Make sure to lock the door tight when you go out.
•
Do not use water and any type of solvent to clean the product such as
gasoline or benzene as they can cause damage to electronic circuit,
deterioration and or paint peel-off.
•
It is recommended to change User Code on a regular basis.
•
In manual lock mode, make sure to double check whether the door is
securely locked.
•
When External Forced lock is set and unlock the door, the alarm will be
activated.
•
Do not use rechargeable batteries. Only alkaline batteries are recommended.
•
Make sure to follow the above instructions to avoid any injuries.
•
It cannot be guaranteed in a special conditions & environment such as
water condensation, seaside.
•
Warranty will not cover- exposure to dampness, excessive heat,
excessive humidity and other extreme environmental conditions,
corrosion, damage beyond repair, rusting, unauthorised modifications,
unauthorised repairs, neglect, accident, alteration, acts of God,
spillage of liquid or food particles.
Master mode is a mode in which only the administrator can set the door lock and provide
access to other users. 100 users passwords, 100 users RFID key tags,100 users fingerprint and
individual registration and deletion of one-time passwords enable efficient management of visitors.
Change
Mode New Again
Switch to master mode (from normal mode)
PIN CODE
UPIN CODE MPIN CODE M
Change
Mode New Again
Switch to normal mode (from master mode)
PIN CODE
UPIN CODE U
OR
Registr
-ation New Again
Master Pin Code Change
PIN CODE
M
PIN CODE
M
PIN CODE
M
Delete
OR
Registr
-ation
User Code
PIN CODE
U
UN
OR
UN
PIN CODE
M
Up to 100 Users
Only 1 User
Delete
OR
Registr
-ation
Fingerprint
UN
OR
UN
PIN CODE
M
Up to 100 Users
Delete
Registr
-ation
Onetime Code
OR
OR
PIN CODE
M
PIN CODE
M
PIN CODE
O
Only 1 User, Automatically deleted after use
Langu
-age
Setting
Language Change
OR
OR
OR
OR
OR
Delete
Delete all credentials
PIN CODE
M
PIN CODE
M
PIN CODE
M
Registr
-ation
Bluetooth Setting (Yale Access App)
PIN CODE
M
Delete
Registr
-ation
Remote Controller
OR
OR
PIN CODE
M
Up to 5 Users
UN
UN
Button
SET
Delete
Registr
-ation
Home Network Controller
OR
OR
PIN CODE
Mroller
Cont
PIN CODE
M
PIN CODE
M
Korean
Chinese
English
Taiwanese
8times
Set up a new device in the app
14 (Registration process)
1
High
Low
Mute
Volume Control
PIN CODE
M
OR
OR
OR
Disable
Enable
Automatic Lock
PIN CODE
M
Continue / Complete
Enable External Forced Lock : Fingerprint
Scan with registered fingerprint and hold the fingerprint area
until you hear 3 beep sounds.
Disable External Forced Lock
When the door is unlocked from outside based upon proper
authentication, the External forced lock will be released.
Palm touch Enter the
User PIN Code
Enter the
button for 5 Sec.
Enable External Forced Lock : User Code
※If you try to open a door with the manual thumb turn knob from inside when the Outside Forced Lock is set,
the alarm goes off.
※If the Inside Forced Lock is set, any attempt to open a door from outside whether it’s be a Fingerprint or
code won’t work.
Press Open/Close button
for 3 seconds until
you hear “pik” beep.
Method 1 :
Press Open/Close
button for 3 seconds
until you hear
“pik” beep.
Method 2 :
Turn manual
thumb turn knob.
Setting
‘ 3 ’
Seconds
Release
‘ 3 ’
Seconds
Turn it
OR
OR
ISL-1857-00-046
PLEASE READ INSTRUCTIONS BEFORE USE.
The functions and design of this product can be changed
without prior notice for performance and quality improvement.
Packaging of this product can be recycled.
User Slot Number should be 2 digits.
like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100".
※
22. Code Chart
Duplicate if necessary
PIN Code Management(Up to 100 Users.)
Do not install the digital door
lock in an outdoor environment.
24. Important notes
Do not attempt to disassemble
the digital door lock by yourself.
Do not spray water directly
or wipe with chemicals such as
benzene, gasoline or alcohol.
Do not use force with a tool
onto the product.
When using, remember that
someone else can see the
password.
Make sure the door is closed
properly when going out.
25. Safety and Warning
※Voice guidance : Voice guidance features assist in easy navigation through various features.
※All registered passwords and other credentials will be deleted when mode is changed.
※Please install(register) the network module when you want to use a remote control or home network.
Part of ASSA ABLOY
You must replace all 4 batteries in the following cases:
* The Low Battery LED on keypad flickers red.
* When low battery notification message is played.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE NATIONAL CODE OR RECYCLING PROGRAM.
Palm touch Palm touchEnter the user code
and fake code
Enter the Fake Code
and User code
OR
Enable External Forced Lock : RFID Key Tag
Contact RFID key tag on [RFID key tag reader] for 5 sec. until you
hear 3 beeps.
※In case of discharged batteries, please use 9V battery to supply power
Palm
touch
OR OR
Contact 9V
battery
Enter the User Code
and Plam touch
Contact
RFID Key Tag
Scan
fingerprint
Delete
OR
Registr
-ation
RFID Key Tag
UN
OR
UN
PIN CODE
M
Up to 100 Users

16. Internal Forced Lock
15. External Forced Lock
User Guide
RFID Key Tag / Fingerprint / PIN Code / Key
YDD724A
23. Master Mode
17. Alarm
18. 3 Minute Lock Out
19. Unlocking Door with Fake Code
Intrusion Alarm : The alarm goes off when someone forces the door open.
For example, In case of an intrusion by opening a gap
in the door while the door is locked.
Broken Alarm(Breakage Alarm) : The alarm goes off when the front part is
completely separated from the main set. For example,
forced removal of external product (front body).
Turn off Alarm
There is no limitation for
digits of Fake Pin Code.
Disable 3-minute Lock Out
All access mode from the external side are disabled for 3 minutes to deter
unauthorized access.
Press the Open/Close button.
Open the door with mechanical key.
Press button.
Enter the registered User Code.
Scan the registered fingerprint.
Press and hold the O/C Button for 5seconds.
Touch the registered RFID Key Tag.
20. Power supply
21. Emergency power supply for discharged batteries
One-on-one real life size
1.5V(LR6) Alkaline AA Battery
It may sustain 1 year if used 10 times
a day. (Users are advised to use
authentic Alkaline batteries.)
* Kindly dispose used batteries.
•
Do not install the digital door lock in an outdoor environment.
•
Do not attempt to disassemble the digital door lock by your self.
By doing so, you may get an electronic shock and damage the product.
•
Do not use force with a tool onto the product.
•
Make sure to lock the door tight when you go out.
•
Do not use water and any type of solvent to clean the product such as
gasoline or benzene as they can cause damage to electronic circuit,
deterioration and or paint peel-off.
•
It is recommended to change User Code on a regular basis.
•
In manual lock mode, make sure to double check whether the door is
securely locked.
•
When External Forced lock is set and unlock the door, the alarm will be
activated.
•
Do not use rechargeable batteries. Only alkaline batteries are recommended.
•
Make sure to follow the above instructions to avoid any injuries.
•
It cannot be guaranteed in a special conditions & environment such as
water condensation, seaside.
•
Warranty will not cover- exposure to dampness, excessive heat,
excessive humidity and other extreme environmental conditions,
corrosion, damage beyond repair, rusting, unauthorised modifications,
unauthorised repairs, neglect, accident, alteration, acts of God,
spillage of liquid or food particles.
Master mode is a mode in which only the administrator can set the door lock and provide
access to other users. 100 users passwords, 100 users RFID key tags,100 users fingerprint and
individual registration and deletion of one-time passwords enable efficient management of visitors.
Change
Mode New Again
Switch to master mode (from normal mode)
PIN CODE
UPIN CODE MPIN CODE M
Change
Mode New Again
Switch to normal mode (from master mode)
PIN CODE
UPIN CODE U
OR
Registr
-ation New Again
Master Pin Code Change
PIN CODE
M
PIN CODE
M
PIN CODE
M
Delete
OR
Registr
-ation
User Code
PIN CODE
U
UN
OR
UN
PIN CODE
M
Up to 100 Users
Only 1 User
Delete
OR
Registr
-ation
Fingerprint
UN
OR
UN
PIN CODE
M
Up to 100 Users
Delete
Registr
-ation
Onetime Code
OR
OR
PIN CODE
M
PIN CODE
M
PIN CODE
O
Only 1 User, Automatically deleted after use
Langu
-age
Setting
Language Change
OR
OR
OR
OR
OR
Delete
Delete all credentials
PIN CODE
M
PIN CODE
M
PIN CODE
M
Registr
-ation
Bluetooth Setting (Yale Access App)
PIN CODE
M
Delete
Registr
-ation
Remote Controller
OR
OR
PIN CODE
M
Up to 5 Users
UN
UN
Button
SET
Delete
Registr
-ation
Home Network Controller
OR
OR
PIN CODE
Mroller
Cont
PIN CODE
M
PIN CODE
M
Korean
Chinese
English
Taiwanese
8times
Set up a new device in the app
14 (Registration process)
1
High
Low
Mute
Volume Control
PIN CODE
M
OR
OR
OR
Disable
Enable
Automatic Lock
PIN CODE
M
Continue / Complete
Enable External Forced Lock : Fingerprint
Scan with registered fingerprint and hold the fingerprint area
until you hear 3 beep sounds.
Disable External Forced Lock
When the door is unlocked from outside based upon proper
authentication, the External forced lock will be released.
Palm touch Enter the
User PIN Code
Enter the
button for 5 Sec.
Enable External Forced Lock : User Code
※If you try to open a door with the manual thumb turn knob from inside when the Outside Forced Lock is set,
the alarm goes off.
※If the Inside Forced Lock is set, any attempt to open a door from outside whether it’s be a Fingerprint or
code won’t work.
Press Open/Close button
for 3 seconds until
you hear “pik” beep.
Method 1 :
Press Open/Close
button for 3 seconds
until you hear
“pik” beep.
Method 2 :
Turn manual
thumb turn knob.
Setting
‘ 3 ’
Seconds
Release
‘ 3 ’
Seconds
Turn it
OR
OR
ISL-1857-00-046
PLEASE READ INSTRUCTIONS BEFORE USE.
The functions and design of this product can be changed
without prior notice for performance and quality improvement.
Packaging of this product can be recycled.
User Slot Number should be 2 digits.
like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100".
※
22. Code Chart
Duplicate if necessary
PIN Code Management(Up to 100 Users.)
Do not install the digital door
lock in an outdoor environment.
24. Important notes
Do not attempt to disassemble
the digital door lock by yourself.
Do not spray water directly
or wipe with chemicals such as
benzene, gasoline or alcohol.
Do not use force with a tool
onto the product.
When using, remember that
someone else can see the
password.
Make sure the door is closed
properly when going out.
25. Safety and Warning
※Voice guidance : Voice guidance features assist in easy navigation through various features.
※All registered passwords and other credentials will be deleted when mode is changed.
※Please install(register) the network module when you want to use a remote control or home network.
Part of ASSA ABLOY
You must replace all 4 batteries in the following cases:
* The Low Battery LED on keypad flickers red.
* When low battery notification message is played.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE NATIONAL CODE OR RECYCLING PROGRAM.
Palm touch Palm touchEnter the user code
and fake code
Enter the Fake Code
and User code
OR
Enable External Forced Lock : RFID Key Tag
Contact RFID key tag on [RFID key tag reader] for 5 sec. until you
hear 3 beeps.
※In case of discharged batteries, please use 9V battery to supply power
Palm
touch
OR OR
Contact 9V
battery
Enter the User Code
and Plam touch
Contact
RFID Key Tag
Scan
fingerprint
Delete
OR
Registr
-ation
RFID Key Tag
UN
OR
UN
PIN CODE
M
Up to 100 Users

16. Internal Forced Lock
15. External Forced Lock
User Guide
RFID Key Tag / Fingerprint / PIN Code / Key
YDD724A
23. Master Mode
17. Alarm
18. 3 Minute Lock Out
19. Unlocking Door with Fake Code
Intrusion Alarm : The alarm goes off when someone forces the door open.
For example, In case of an intrusion by opening a gap
in the door while the door is locked.
Broken Alarm(Breakage Alarm) : The alarm goes off when the front part is
completely separated from the main set. For example,
forced removal of external product (front body).
Turn off Alarm
There is no limitation for
digits of Fake Pin Code.
Disable 3-minute Lock Out
All access mode from the external side are disabled for 3 minutes to deter
unauthorized access.
Press the Open/Close button.
Open the door with mechanical key.
Press button.
Enter the registered User Code.
Scan the registered fingerprint.
Press and hold the O/C Button for 5seconds.
Touch the registered RFID Key Tag.
20. Power supply
21. Emergency power supply for discharged batteries
One-on-one real life size
1.5V(LR6) Alkaline AA Battery
It may sustain 1 year if used 10 times
a day. (Users are advised to use
authentic Alkaline batteries.)
* Kindly dispose used batteries.
•
Do not install the digital door lock in an outdoor environment.
•
Do not attempt to disassemble the digital door lock by your self.
By doing so, you may get an electronic shock and damage the product.
•
Do not use force with a tool onto the product.
•
Make sure to lock the door tight when you go out.
•
Do not use water and any type of solvent to clean the product such as
gasoline or benzene as they can cause damage to electronic circuit,
deterioration and or paint peel-off.
•
It is recommended to change User Code on a regular basis.
•
In manual lock mode, make sure to double check whether the door is
securely locked.
•
When External Forced lock is set and unlock the door, the alarm will be
activated.
•
Do not use rechargeable batteries. Only alkaline batteries are recommended.
•
Make sure to follow the above instructions to avoid any injuries.
•
It cannot be guaranteed in a special conditions & environment such as
water condensation, seaside.
•
Warranty will not cover- exposure to dampness, excessive heat,
excessive humidity and other extreme environmental conditions,
corrosion, damage beyond repair, rusting, unauthorised modifications,
unauthorised repairs, neglect, accident, alteration, acts of God,
spillage of liquid or food particles.
Master mode is a mode in which only the administrator can set the door lock and provide
access to other users. 100 users passwords, 100 users RFID key tags,100 users fingerprint and
individual registration and deletion of one-time passwords enable efficient management of visitors.
Change
Mode New Again
Switch to master mode (from normal mode)
PIN CODE
UPIN CODE MPIN CODE M
Change
Mode New Again
Switch to normal mode (from master mode)
PIN CODE
UPIN CODE U
OR
Registr
-ation New Again
Master Pin Code Change
PIN CODE
M
PIN CODE
M
PIN CODE
M
Delete
OR
Registr
-ation
User Code
PIN CODE
U
UN
OR
UN
PIN CODE
M
Up to 100 Users
Only 1 User
Delete
OR
Registr
-ation
Fingerprint
UN
OR
UN
PIN CODE
M
Up to 100 Users
Delete
Registr
-ation
Onetime Code
OR
OR
PIN CODE
M
PIN CODE
M
PIN CODE
O
Only 1 User, Automatically deleted after use
Langu
-age
Setting
Language Change
OR
OR
OR
OR
OR
Delete
Delete all credentials
PIN CODE
M
PIN CODE
M
PIN CODE
M
Registr
-ation
Bluetooth Setting (Yale Access App)
PIN CODE
M
Delete
Registr
-ation
Remote Controller
OR
OR
PIN CODE
M
Up to 5 Users
UN
UN
Button
SET
Delete
Registr
-ation
Home Network Controller
OR
OR
PIN CODE
Mroller
Cont
PIN CODE
M
PIN CODE
M
Korean
Chinese
English
Taiwanese
8times
Set up a new device in the app
14 (Registration process)
1
High
Low
Mute
Volume Control
PIN CODE
M
OR
OR
OR
Disable
Enable
Automatic Lock
PIN CODE
M
Continue / Complete
Enable External Forced Lock : Fingerprint
Scan with registered fingerprint and hold the fingerprint area
until you hear 3 beep sounds.
Disable External Forced Lock
When the door is unlocked from outside based upon proper
authentication, the External forced lock will be released.
Palm touch Enter the
User PIN Code
Enter the
button for 5 Sec.
Enable External Forced Lock : User Code
※If you try to open a door with the manual thumb turn knob from inside when the Outside Forced Lock is set,
the alarm goes off.
※If the Inside Forced Lock is set, any attempt to open a door from outside whether it’s be a Fingerprint or
code won’t work.
Press Open/Close button
for 3 seconds until
you hear “pik” beep.
Method 1 :
Press Open/Close
button for 3 seconds
until you hear
“pik” beep.
Method 2 :
Turn manual
thumb turn knob.
Setting
‘ 3 ’
Seconds
Release
‘ 3 ’
Seconds
Turn it
OR
OR
ISL-1857-00-046
PLEASE READ INSTRUCTIONS BEFORE USE.
The functions and design of this product can be changed
without prior notice for performance and quality improvement.
Packaging of this product can be recycled.
User Slot Number should be 2 digits.
like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100".
※
22. Code Chart
Duplicate if necessary
PIN Code Management(Up to 100 Users.)
Do not install the digital door
lock in an outdoor environment.
24. Important notes
Do not attempt to disassemble
the digital door lock by yourself.
Do not spray water directly
or wipe with chemicals such as
benzene, gasoline or alcohol.
Do not use force with a tool
onto the product.
When using, remember that
someone else can see the
password.
Make sure the door is closed
properly when going out.
25. Safety and Warning
※Voice guidance : Voice guidance features assist in easy navigation through various features.
※All registered passwords and other credentials will be deleted when mode is changed.
※Please install(register) the network module when you want to use a remote control or home network.
Part of ASSA ABLOY
You must replace all 4 batteries in the following cases:
* The Low Battery LED on keypad flickers red.
* When low battery notification message is played.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE NATIONAL CODE OR RECYCLING PROGRAM.
Palm touch Palm touchEnter the user code
and fake code
Enter the Fake Code
and User code
OR
Enable External Forced Lock : RFID Key Tag
Contact RFID key tag on [RFID key tag reader] for 5 sec. until you
hear 3 beeps.
※In case of discharged batteries, please use 9V battery to supply power
Palm
touch
OR OR
Contact 9V
battery
Enter the User Code
and Plam touch
Contact
RFID Key Tag
Scan
fingerprint
Delete
OR
Registr
-ation
RFID Key Tag
UN
OR
UN
PIN CODE
M
Up to 100 Users

16. Internal Forced Lock
15. External Forced Lock
User Guide
RFID Key Tag / Fingerprint / PIN Code / Key
YDD724A
23. Master Mode
17. Alarm
18. 3 Minute Lock Out
19. Unlocking Door with Fake Code
Intrusion Alarm : The alarm goes off when someone forces the door open.
For example, In case of an intrusion by opening a gap
in the door while the door is locked.
Broken Alarm(Breakage Alarm) : The alarm goes off when the front part is
completely separated from the main set. For example,
forced removal of external product (front body).
Turn off Alarm
There is no limitation for
digits of Fake Pin Code.
Disable 3-minute Lock Out
All access mode from the external side are disabled for 3 minutes to deter
unauthorized access.
Press the Open/Close button.
Open the door with mechanical key.
Press button.
Enter the registered User Code.
Scan the registered fingerprint.
Press and hold the O/C Button for 5seconds.
Touch the registered RFID Key Tag.
20. Power supply
21. Emergency power supply for discharged batteries
One-on-one real life size
1.5V(LR6) Alkaline AA Battery
It may sustain 1 year if used 10 times
a day. (Users are advised to use
authentic Alkaline batteries.)
* Kindly dispose used batteries.
•
Do not install the digital door lock in an outdoor environment.
•
Do not attempt to disassemble the digital door lock by your self.
By doing so, you may get an electronic shock and damage the product.
•
Do not use force with a tool onto the product.
•
Make sure to lock the door tight when you go out.
•
Do not use water and any type of solvent to clean the product such as
gasoline or benzene as they can cause damage to electronic circuit,
deterioration and or paint peel-off.
•
It is recommended to change User Code on a regular basis.
•
In manual lock mode, make sure to double check whether the door is
securely locked.
•
When External Forced lock is set and unlock the door, the alarm will be
activated.
•
Do not use rechargeable batteries. Only alkaline batteries are recommended.
•
Make sure to follow the above instructions to avoid any injuries.
•
It cannot be guaranteed in a special conditions & environment such as
water condensation, seaside.
•
Warranty will not cover- exposure to dampness, excessive heat,
excessive humidity and other extreme environmental conditions,
corrosion, damage beyond repair, rusting, unauthorised modifications,
unauthorised repairs, neglect, accident, alteration, acts of God,
spillage of liquid or food particles.
Master mode is a mode in which only the administrator can set the door lock and provide
access to other users. 100 users passwords, 100 users RFID key tags,100 users fingerprint and
individual registration and deletion of one-time passwords enable efficient management of visitors.
Change
Mode New Again
Switch to master mode (from normal mode)
PIN CODE
UPIN CODE MPIN CODE M
Change
Mode New Again
Switch to normal mode (from master mode)
PIN CODE
UPIN CODE U
OR
Registr
-ation New Again
Master Pin Code Change
PIN CODE
M
PIN CODE
M
PIN CODE
M
Delete
OR
Registr
-ation
User Code
PIN CODE
U
UN
OR
UN
PIN CODE
M
Up to 100 Users
Only 1 User
Delete
OR
Registr
-ation
Fingerprint
UN
OR
UN
PIN CODE
M
Up to 100 Users
Delete
Registr
-ation
Onetime Code
OR
OR
PIN CODE
M
PIN CODE
M
PIN CODE
O
Only 1 User, Automatically deleted after use
Langu
-age
Setting
Language Change
OR
OR
OR
OR
OR
Delete
Delete all credentials
PIN CODE
M
PIN CODE
M
PIN CODE
M
Registr
-ation
Bluetooth Setting (Yale Access App)
PIN CODE
M
Delete
Registr
-ation
Remote Controller
OR
OR
PIN CODE
M
Up to 5 Users
UN
UN
Button
SET
Delete
Registr
-ation
Home Network Controller
OR
OR
PIN CODE
Mroller
Cont
PIN CODE
M
PIN CODE
M
Korean
Chinese
English
Taiwanese
8times
Set up a new device in the app
14 (Registration process)
1
High
Low
Mute
Volume Control
PIN CODE
M
OR
OR
OR
Disable
Enable
Automatic Lock
PIN CODE
M
Continue / Complete
Enable External Forced Lock : Fingerprint
Scan with registered fingerprint and hold the fingerprint area
until you hear 3 beep sounds.
Disable External Forced Lock
When the door is unlocked from outside based upon proper
authentication, the External forced lock will be released.
Palm touch Enter the
User PIN Code
Enter the
button for 5 Sec.
Enable External Forced Lock : User Code
※If you try to open a door with the manual thumb turn knob from inside when the Outside Forced Lock is set,
the alarm goes off.
※If the Inside Forced Lock is set, any attempt to open a door from outside whether it’s be a Fingerprint or
code won’t work.
Press Open/Close button
for 3 seconds until
you hear “pik” beep.
Method 1 :
Press Open/Close
button for 3 seconds
until you hear
“pik” beep.
Method 2 :
Turn manual
thumb turn knob.
Setting
‘ 3 ’
Seconds
Release
‘ 3 ’
Seconds
Turn it
OR
OR
ISL-1857-00-046
PLEASE READ INSTRUCTIONS BEFORE USE.
The functions and design of this product can be changed
without prior notice for performance and quality improvement.
Packaging of this product can be recycled.
User Slot Number should be 2 digits.
like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100".
※
22. Code Chart
Duplicate if necessary
PIN Code Management(Up to 100 Users.)
Do not install the digital door
lock in an outdoor environment.
24. Important notes
Do not attempt to disassemble
the digital door lock by yourself.
Do not spray water directly
or wipe with chemicals such as
benzene, gasoline or alcohol.
Do not use force with a tool
onto the product.
When using, remember that
someone else can see the
password.
Make sure the door is closed
properly when going out.
25. Safety and Warning
※Voice guidance : Voice guidance features assist in easy navigation through various features.
※All registered passwords and other credentials will be deleted when mode is changed.
※Please install(register) the network module when you want to use a remote control or home network.
Part of ASSA ABLOY
You must replace all 4 batteries in the following cases:
* The Low Battery LED on keypad flickers red.
* When low battery notification message is played.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE NATIONAL CODE OR RECYCLING PROGRAM.
Palm touch Palm touchEnter the user code
and fake code
Enter the Fake Code
and User code
OR
Enable External Forced Lock : RFID Key Tag
Contact RFID key tag on [RFID key tag reader] for 5 sec. until you
hear 3 beeps.
※In case of discharged batteries, please use 9V battery to supply power
Palm
touch
OR OR
Contact 9V
battery
Enter the User Code
and Plam touch
Contact
RFID Key Tag
Scan
fingerprint
Delete
OR
Registr
-ation
RFID Key Tag
UN
OR
UN
PIN CODE
M
Up to 100 Users

16. Internal Forced Lock
15. External Forced Lock
User Guide
RFID Key Tag / Fingerprint / PIN Code / Key
YDD724A
23. Master Mode
17. Alarm
18. 3 Minute Lock Out
19. Unlocking Door with Fake Code
Intrusion Alarm : The alarm goes off when someone forces the door open.
For example, In case of an intrusion by opening a gap
in the door while the door is locked.
Broken Alarm(Breakage Alarm) : The alarm goes off when the front part is
completely separated from the main set. For example,
forced removal of external product (front body).
Turn off Alarm
There is no limitation for
digits of Fake Pin Code.
Disable 3-minute Lock Out
All access mode from the external side are disabled for 3 minutes to deter
unauthorized access.
Press the Open/Close button.
Open the door with mechanical key.
Press button.
Enter the registered User Code.
Scan the registered fingerprint.
Press and hold the O/C Button for 5seconds.
Touch the registered RFID Key Tag.
20. Power supply
21. Emergency power supply for discharged batteries
One-on-one real life size
1.5V(LR6) Alkaline AA Battery
It may sustain 1 year if used 10 times
a day. (Users are advised to use
authentic Alkaline batteries.)
* Kindly dispose used batteries.
•
Do not install the digital door lock in an outdoor environment.
•
Do not attempt to disassemble the digital door lock by your self.
By doing so, you may get an electronic shock and damage the product.
•
Do not use force with a tool onto the product.
•
Make sure to lock the door tight when you go out.
•
Do not use water and any type of solvent to clean the product such as
gasoline or benzene as they can cause damage to electronic circuit,
deterioration and or paint peel-off.
•
It is recommended to change User Code on a regular basis.
•
In manual lock mode, make sure to double check whether the door is
securely locked.
•
When External Forced lock is set and unlock the door, the alarm will be
activated.
•
Do not use rechargeable batteries. Only alkaline batteries are recommended.
•
Make sure to follow the above instructions to avoid any injuries.
•
It cannot be guaranteed in a special conditions & environment such as
water condensation, seaside.
•
Warranty will not cover- exposure to dampness, excessive heat,
excessive humidity and other extreme environmental conditions,
corrosion, damage beyond repair, rusting, unauthorised modifications,
unauthorised repairs, neglect, accident, alteration, acts of God,
spillage of liquid or food particles.
Master mode is a mode in which only the administrator can set the door lock and provide
access to other users. 100 users passwords, 100 users RFID key tags,100 users fingerprint and
individual registration and deletion of one-time passwords enable efficient management of visitors.
Change
Mode New Again
Switch to master mode (from normal mode)
PIN CODE
UPIN CODE MPIN CODE M
Change
Mode New Again
Switch to normal mode (from master mode)
PIN CODE
UPIN CODE U
OR
Registr
-ation New Again
Master Pin Code Change
PIN CODE
M
PIN CODE
M
PIN CODE
M
Delete
OR
Registr
-ation
User Code
PIN CODE
U
UN
OR
UN
PIN CODE
M
Up to 100 Users
Only 1 User
Delete
OR
Registr
-ation
Fingerprint
UN
OR
UN
PIN CODE
M
Up to 100 Users
Delete
Registr
-ation
Onetime Code
OR
OR
PIN CODE
M
PIN CODE
M
PIN CODE
O
Only 1 User, Automatically deleted after use
Langu
-age
Setting
Language Change
OR
OR
OR
OR
OR
Delete
Delete all credentials
PIN CODE
M
PIN CODE
M
PIN CODE
M
Registr
-ation
Bluetooth Setting (Yale Access App)
PIN CODE
M
Delete
Registr
-ation
Remote Controller
OR
OR
PIN CODE
M
Up to 5 Users
UN
UN
Button
SET
Delete
Registr
-ation
Home Network Controller
OR
OR
PIN CODE
Mroller
Cont
PIN CODE
M
PIN CODE
M
Korean
Chinese
English
Taiwanese
8times
Set up a new device in the app
14 (Registration process)
1
High
Low
Mute
Volume Control
PIN CODE
M
OR
OR
OR
Disable
Enable
Automatic Lock
PIN CODE
M
Continue / Complete
Enable External Forced Lock : Fingerprint
Scan with registered fingerprint and hold the fingerprint area
until you hear 3 beep sounds.
Disable External Forced Lock
When the door is unlocked from outside based upon proper
authentication, the External forced lock will be released.
Palm touch Enter the
User PIN Code
Enter the
button for 5 Sec.
Enable External Forced Lock : User Code
※If you try to open a door with the manual thumb turn knob from inside when the Outside Forced Lock is set,
the alarm goes off.
※If the Inside Forced Lock is set, any attempt to open a door from outside whether it’s be a Fingerprint or
code won’t work.
Press Open/Close button
for 3 seconds until
you hear “pik” beep.
Method 1 :
Press Open/Close
button for 3 seconds
until you hear
“pik” beep.
Method 2 :
Turn manual
thumb turn knob.
Setting
‘ 3 ’
Seconds
Release
‘ 3 ’
Seconds
Turn it
OR
OR
ISL-1857-00-046
PLEASE READ INSTRUCTIONS BEFORE USE.
The functions and design of this product can be changed
without prior notice for performance and quality improvement.
Packaging of this product can be recycled.
User Slot Number should be 2 digits.
like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100".
※
22. Code Chart
Duplicate if necessary
PIN Code Management(Up to 100 Users.)
Do not install the digital door
lock in an outdoor environment.
24. Important notes
Do not attempt to disassemble
the digital door lock by yourself.
Do not spray water directly
or wipe with chemicals such as
benzene, gasoline or alcohol.
Do not use force with a tool
onto the product.
When using, remember that
someone else can see the
password.
Make sure the door is closed
properly when going out.
25. Safety and Warning
※Voice guidance : Voice guidance features assist in easy navigation through various features.
※All registered passwords and other credentials will be deleted when mode is changed.
※Please install(register) the network module when you want to use a remote control or home network.
Part of ASSA ABLOY
You must replace all 4 batteries in the following cases:
* The Low Battery LED on keypad flickers red.
* When low battery notification message is played.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE NATIONAL CODE OR RECYCLING PROGRAM.
Palm touch Palm touchEnter the user code
and fake code
Enter the Fake Code
and User code
OR
Enable External Forced Lock : RFID Key Tag
Contact RFID key tag on [RFID key tag reader] for 5 sec. until you
hear 3 beeps.
※In case of discharged batteries, please use 9V battery to supply power
Palm
touch
OR OR
Contact 9V
battery
Enter the User Code
and Plam touch
Contact
RFID Key Tag
Scan
fingerprint
Delete
OR
Registr
-ation
RFID Key Tag
UN
OR
UN
PIN CODE
M
Up to 100 Users