Assa Abloy v.G1 Sargent User manual

Installation Instructions For
Profile Series v.G1 Mortise Lock
A7756A
Copyright © 2006, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
FOR ASSISTANCE, CONTACT SARGENT AT 800-727-5477 or www.sargentlock.com

800-810-WIRE (9473) • www.sargentlock.com • A7756A
Copyright © 2006, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Table of Contents
Warning
General Description...........................................................................1
Specifications....................................................................................1
Features.............................................................................................1
Parts Breakdown.............................................................................2-3
Installation Instructions..................................................................4-9
Operational Check............................................................................10
Installation of the RF Technology Lock (G1-TU, G1-TA, G1-TP)......10
Page
1
2
3
4
5
6
7
8
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme avec la norme NMB-003 du Canada.
Warning
1Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Warning
!To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.

1
800-810-WIRE (9473) • www.sargentlock.com • A7756A
Profile Series v.G1 Mortise Lock
Copyright © 2006, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
The SARGENT Profile v.G1 Mortise Lock is designed for areas which require stand alone authorized entry. It is a
self-contained microprocessor-controlled keypad with non-volatile memory. The keypad will hold a total of
100(LK)/2000 (G1-LU, G1-PK, G1-PA, G1-TU, G1-TP, G1-TA) different user codes. User codes “01” & “02” are
utilized for Master and Supervisory Codes, respectively.
This product is operated by six (6) “AA” alkaline batteries. SARGENT mortise locks are designed with quality
components to provide high security, performance and durability.
General Description
2
Specifications
• Latch - Stainless steel
• Deadbolt - Stainless steel
• Guardbolt - Stainless steel, non handed
• Handed - Easily field reversible without
disassembling the lock body
• Case - 12 gauge heavy duty wrought steel
• Outside lever controlled by any combination of
keypad, Proximity or RF Technology
• Inside lever retracts latch and deadbolt
• Locks furnished for 1-3/4" doors. Can be
furnished for other door sizes upon request.
Consult factory
• U.L. Listed (3 hr.)
Features
• Low battery alert–4 chirps after code entry
• External remote “request to enter” connector
• Master, Emergency or Supervisory code will
unlock door when low battery has expired
• Programming done at the keypad (Except
G1-PA & G1-TA) or with a PDA using SofLink
Plus software and a PC
• Entry of three wrong User Codes disables all
codes for ten seconds. Yellow LED on solid
• Last 15 transactions can be output to
portable printer via infrared link (LK Only)
• Last 2000 (Except LK) transactions can be output
to a PC via a PDA and SofLink™ Plus software
3
4

2800-810-WIRE (9473) • www.sargentlock.com • A7756A
Profile Series v.G1 Mortise Lock
Copyright © 2006, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
11
13
27/28
29
5
4
3
7
2, 2B
16
17
15
14
8915
31
21
22 20
20
18/19
25
23
24
26
21
22
26
16
1
17
30
13
13
12
24
33
5Parts Breakdown

3
800-810-WIRE (9473) • www.sargentlock.com • A7756A
Profile Series v.G1 Mortise Lock
Copyright © 2006, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
5Parts Breakdown (Continued)
ITEM PART No. DESCRIPTION REQ’D
1
82-4190 Outside Escutcheon with Cylinder Hole and Key Pad, or Key Pad/Prox (G1-LU, G1-PK, G1-TU, G1-TP) 1
82-4191 Outside Escutcheon without Cylinder Hole and Key Pad or Key Pad/Prox (G1-LU, G1-PK, G1-TU, G1-TP) 1
82-4192 Outside Escutcheon with Cylinder Hole and Prox Only (G1-PA, G1-TA) 1
82-4193 Outside Escutcheon without Cylinder Hole and Prox Only (G1-PA, G1-TA) 1
82-0493 Outside Escutcheon Housing Only without Cylinder Hole 1
82-0495 Outside Escutcheon Housing Only with Cylinder Hole 1
52-2432 Keypad/Proximity Bezel Assembly w/ Harness (LK) 1
52-2706 Proximity Only Bezel Assembly with Harness (G1-PA, G1-TA) 1
52-2704 Key Pad/Proximity Bezel Assembly with Harness (G1-LU, G1-PK, G1-TU, G1-TP) 1
2 82-3837 Inside Escutcheon with Thumb Turn and 100 User Controller (LK) 1
82-3838 Inside Escutcheon without Thumb Turn and 100 User Controller (LK) 1
82-4182 Inside Escutcheon with Thumb Turn and 2000 User Controller (G1-LU) 1
82-4183 Inside Escutcheon without Thumb Turn and 2000 User Controller (G1-LU) 1
82-4184 Inside Escutcheon with Thumb Turn Prox/Key Pad Controller (G1-PA, G1-PK) 1
82-4185 Inside Escutcheon without Thumb Turn Prox/Key Pad Cont. (G1-PA, G1-PK) 1
82-4186 Inside Escutcheon with Thumb Turn & 2000 User Controller with RF Technology (G1-TU) 1
82-4187 Inside Escutcheon Less Thumb Turn & 2000 User Controller with RF Technology (G1-TU) 1
82-4188 Inside Escutcheon with Thumb Turn & Keypad/Prox or Prox Only Controller (G1-TA, G1-TP) 1
82-4189 Inside Escutcheon Less Thumb Turn & Keypad Prox or Prox Only Controller (G1-TA, G1-TP) 1
82-0492 Inside Escutcheon Housing Only without Thumb Turn 1
82-0494 Inside Escutcheon Housing Only with Thumb Turn 1
52-2440 100 (LK) User Key Pad Controller Assembly 1
52-2783 2000 (G1-LU) User Controller Assembly 1
52-2784 2000 User (G1-PA, G1-PK) Controller Assembly 1
52-2786 2000 User Keypad/Prox Controller Assembly w/ RF Technology (G1-TA, G1-TP)
52-2785 2000 User Keypad Controller Assembly w/ RF Technology (G1-TU)
3 52-0170 Battery Cover 1
52-2509 Battery Cover – RF Technology (G1-TU,G1-TP, G1-TA)
4 01-1212 Security Screw 1
5 01-0297 Security Tool 1
7 82-0507 Thumb Turn 1
8 77-0772 Spindle (Thumb Turn) 1
9 01-0844 Washer (Thumb Turn) 1
10 01-0543 Spring Grip Fastener (Thumb Turn) 1
11 77-0168 Through-bolts #8-32 x 1 7/8” Flat Head Screw 2
12 52-0033 Fire Stop Plate 1
13 01-1500 Fire Stop Screws #8 x 1/2” Type “AB” Phillips Pan Head Self Tap 2
14 82-3088 Inside Spindle Adapter & Plate Assembly 1
15 01-1495 Screw #8-32 x 1/2” 2
16 82-0368 Inside Spindle/Outside Spindle 2
17 82-0347 Inside Spring/Outside Spring 2
18 82-0081 Face Plate no Dead Bolt 1
19 82-0084 Face Plate with Dead Bolt 1
20 01-1028 Face Plate Screws Machine 8-32 x 1/4” 2
21 01-2299 Lock Body Screws/Wood Door #12 x 1 1/4” 2
22 01-1019 Lock Body Screws/Metal Door 12-24 x 1/2” 2
23 82-0184 Cap Nut 1
24 01-0079 Washer 2
25 82-3082 Plate Assembly 1
26 81-0723 Post 2
27 01-1472 Lever Handle Screw, A, E & F Lever 1
28 01-1174 Lever Handle Screw, B, J, L, P & W Lever 1
29
Reference Profile Series catalog for available lever handles
30
31 82-3732 Lockbody Assembly (with deadbolt) (8276 & 8277) 1
82-3733 Lockbody Assembly (without deadbolt) (8278 & 8279) 1
32 01-0803 Battery Alkaline (“AA” cell) 6
33 52-0253 Battery Keeper 1
52-0344 Battery Keeper – RF Technology (G1-TU, G1-TP, G1-TA)

4800-810-WIRE (9473) • www.sargentlock.com • A7756A
Profile Series v.G1 Mortise Lock
Copyright © 2006, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Left Hand
Hinges Left.
Open inward.
“LH”
Left Hand
Reverse Bevel
Hinges Left.
Open Outward
“LHRB”
Right Hand
Hinges Right
Open Inward.
“RH”
Right Hand
Reverse Bevel
Hinges Right.
Open Outward.
“RHRB”
Installation Instructions
6
Verify Hand and Bevel of Door
Before Starting
Prep door according to Instruction Sheet A7454 and appropriate template:
Wood door - A7457
Metal door - 4533 for 8276/8278
Metal door - 4534 for 8277/8279
Step #1 – Door Preparation

5
800-810-WIRE (9473) • www.sargentlock.com • A7756A
Profile Series v.G1 Mortise Lock
Copyright © 2006, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Step #2 – How to Reverse Lock Hand
RED color
locking piece
indicates locked side
End Cap
Connector
If it is necessary to change hand of latch:
1. Insert blade of common screwdriver into triangular slot behind latch.
2. Rotate screw driver and push latch out until back of bolt clears lockbody front.
3. Rotate latch 180° until the latch drops back into the lockbody.
If it is necessary to change hand of locking piece:
1. Turn lockbody to side NOT marked with RED locking piece.
2. Insert blade of common screwdriver into locking piece slot.
3. Push locking piece toward front of lockbody and rotate until RED shows.
4. RED indicates locked (outside) side.
5. Wire harness MUST exit thru non-cylinder side.
Right Hand
Shown
Locking
guide slot
Push in
End
Cap
Latchbolt
Outside of
door
Front
Deadbolt
Dead Latch
Connector
and wires
Triangular
slot
Rotate
Latchbolt

Non Fire Rated Exterior Doors-
Install Weather Conduit
(P/N 52-2847) as shown below
Outside of
door
6800-810-WIRE (9473) • www.sargentlock.com • A7756A
Profile Series v.G1 Mortise Lock
Copyright © 2006, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Inside of
door
(2) #12-24 x 1/2" long
flat head screw
for metal doors
(2) #12 x 1-1/4" long
flat head wood screw
for wood doors
Insert Lockbody in mortised cutout
Hold loosely in place with (2) lockbody screws
DO NOT COMPLETELY TIGHTEN SCREWS
AT THIS TIME
MUST feed
Connector
& Wires thru
non-cylinder
side.
Step #3 – Lockbody Installation
Step #4 – Attach Fire Stop Plate
Wires and connector go into the mortised area and out of the inside cylinder hole
Outside of
door
C
LOf 1-1/2" Dia.
(2) Self tapping
screws #8 x 1/2"
long for wood
& metal doors
(2) 1/8" Dia. holes required
7"
8
1"
2
Slot
1
Fire stop plate
NOTE: Required for 12- fire rated doors.

7
800-810-WIRE (9473) • www.sargentlock.com • A7756A
Profile Series v.G1 Mortise Lock
Copyright © 2006, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Mortise lockbody
connector and wire
Gasket
82-0500
Outside of
door
8-32 x 1-1/4"
Flat Head
Screw
Keypad
harness
Ground
wire
Motor
harness
Inside of
door
With
Deadbolt
Without
Deadbolt
RED
Black
Green
Green
Red
Black
6. Connect ground wire to terminal E3 (Fig. 1), keypad ribbon
cable connector to controller (Fig. 2), and ET motor harness to
motor connector (Fig. 3).
7. Place extra wire inside door hole or outside escutcheon being
careful not to pinch wires
NOTE: Connectors go on only one way, do not offset connector and
be sure they are completely seated
8. Insert #8-32 x 1-1/4" screws through inside escutcheon and thread
into outside escutcheon. Straighten (Ref. Fig. 2) escutcheons and
tighten securely.
NOTE: For RF Technology versions (G1-TU, G1-TP, G1-TA) refer to
Section 8 to install through bolt screws.
Step #5 – Installation of Outside/Inside Escutcheon
& Lever Assembly
NOTE: For exterior applications, gasket (82-0500)
should be used to seal between escutcheon and
outside door surface
1A. For 12- fire rated devices,
feed keypad ribbon cable
connector and ground wire
from outside of door through
gasket and fire stop plate hole
1B. For non-12- exit devices, feed keypad ribbon
cable connector and ground wire through
gasket then through conduit hole in door
2. With outside lever horizontal, insert
mounting posts through door and
lock body. Make certain the lever
spindle is properly engaged in lock.
3. Secure inside adapter and plate assembly by
threading screws into mounting posts of
outside lever assembly
4. Tighten retaining nut by hand, back off slightly
until star pattern lines up with square lever
assembly corners
5. Insert spindle into square hole of adapter plate
Step #6
Fig. 1
Fig. 2
Fig. 3
For RF Technology
see Section 8

8800-810-WIRE (9473) • www.sargentlock.com • A7756A
Profile Series v.G1 Mortise Lock
Copyright © 2006, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Step #7 – Installation of Inside Lever and Outside Cylinder
Inside of
door
•
Set
screw
Inside lever
Spindle
1. Put the turn lever in the horizontal position
(Ref. Fig. 1).
2. Slide lever handle onto spindle until fully seated
(as shown in Fig. 2). Be sure handle is horizontal
and facing to the rear of the door
3. Tighten the set screw securely with 1/8" hex wrench
Fig. 1 Fig. 2
Step #8 – Installation of Cylinder
1. Align cylinder (as shown in Fig. 1).
2. Screw cylinder into lockbody unit (Ref. Fig. 3 for cylinder orientation).
3. Tighten the set screw to prevent unscrewing of the cylinder (Ref. Fig. 2).
4. Turn the keyway in the cylinder to make certain that the locking mechanism
functions correctly.
Outside of door
Type 43 Mortise
cylinder ONLY
Key Phillips
screwdriver
Set screw
Fig. 1
Fig. 3
Fig. 2
SARGENT
SARGENT
Note: Key and
cylinder must be
rotated as shown
Correct Incorrect

9
800-810-WIRE (9473) • www.sargentlock.com • A7756A
Profile Series v.G1 Mortise Lock
Copyright © 2006, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Step #9 – Battery Installation/Application of Front Plate
1. Tighten lockbody screws (Ref. Fig. 1)
2. Attach front plate with (2) flat head screws
Fig. 1
Fig. 3
Fig. 2 Fig. 4

10 800-810-WIRE (9473) • www.sargentlock.com • A7756A
Profile Series v.G1 Mortise Lock
Copyright © 2006, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Operational Check
7
For devices with cylinders:
1. Insert key into cylinder and rotate (There should be no friction against lock case, wire
harness or any other obstructions – refer to Section 6, Step 8 if harness friction exists.
2. The key will retract the latch, key should rotate freely
3. If the deadbolt is thrown, the key will retract both the deadbolt and the latch
4. Inside lever retracts latch and deadbolt (if provided)
5. Enter 1234* to unlock outside lever handle and retract latch and deadbolt
(if provided)
6. If lock is prox only (G1-PA) or RF Technology with prox (G1-TA) - refer to keypad
programming instructions (A7716) to program lock using SofLink Plus™ software.
Installation of RF Technology Lock
8
The RF Technology Lock (G1-TU, G1-TA, G1-TP) is installed as described in sections 1-7 with the
following exceptions: • Installation of the top through-bolt screw
• Removal process for the battery keeper
The antenna board must be carefully moved to access the
upper through-bolt screw. Care should be taken to prevent
damage to the antenna retaining tabs during this process.
Press the two tabs away from the antenna board and lift the
board off the mounting posts. Insert the flat head through-bolt
and secure the escutcheon in place. After tightening the top
through-bolt, replace the antenna board by placing it on the
mounting posts and pressing into the retaining tabs.
A. Installation of the top through-bolt screw:
To remove the battery keeper, a flat bladed screwdriver or similar tool must be used.
Insert the screwdriver into the slot at the top of the battery keeper, lift up and pull the top of the keeper
away from the batteries.
To install, insert the tabs on the bottom of the keeper into the battery compartment slots and press the
keeper tightly against batteries.
B. Removal procedure for the Battery Keeper:
Flathead through-bolt
Antenna
Board
Retaining
Tabs
Mounting
Posts
Controller
Assembly
Insert screwdriver tip
and lift up
Battery
Keeper
Tip out
Keeper tabs