Assa Abloy Norton 8000 Series User manual

Copyright © 2004, 2017 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2206-020 Rev 2 (09-17)
1
ASSA ABLOY
3/16"
#7
1/4-20
for Wood drill 7/32
Machine Screws
#7 Drill, 1/4-20 Tap
Metal Wood
Installation Instructions
NOTE: For special applications a
separate door and frame preparation
template is packed with these instructions.
Use this instruction sheet for installation
sequence and closer adjustments only.
Doors should be hung on ball bearing or
anti-friction hinges.
A separate door stop is recommended.
Door and frame must be properly
reinforced.
Always adjust spring power before
adjusting control.
Adjust closing time speed between 3 and 7
seconds from 90° to 0°. Greater closing
times may be required for elderly or
handicapped.
These door closers should NOT be
installed on the exposed side (weather
side) of exterior doors.
Left Hand Door - LH
Right Hand Reverse - RHR
Right Hand Door - RH
Left Hand Reverse - LHR
Right Hand Door - RH
Left Hand Reverse - LHR
Regular Arm
Installation
See Page 2
Left Hand Door - LH
Right Hand Reverse - RHR
Left Hand Door - LH
Right Hand Reverse - RHR
Top Jamb
Installation
See Page 5
Regular Arm
Installation
See Page 2
Parallel Arm
Installation
See Pages
3 & 4
Parallel Arm
Installation
See Pages
3 & 4
Self Drilling Screws
Wood and Metal
For Wood drill 3/16 hole
Non Hold Open Models
Sized
(Sizes 2,3,4,5,6)
8100
8300
8500
Adjustable
(Sizes 1 thru 6)
8301
8501
8000 Series Tri-Style
Non Handed Door Closer
"DA" suffix (Delayed Action) is an optional
feature.
CAUTION
CAUTION
A n I n c o r r e c t l y i n s t a l l e d o r
improperly adjusted door closer can
cause property damage or personal
injury. These installation instructions
should be followed to avoid the
possibility of misapplication or
misadjustment.
!
* Pilot Hole
Required
Top Jamb
Installation
See Page 5
Right Hand Door - RH
Left Hand Reverse - LHR
Sleeve Nut and Bolt
Thru Bolt and Grommet Nut
Drill 9/32 thru from Closer Side
3/8 Drill other side
Drill 9/32 thru from Closer Side
3/8 Drill other Side
(Optional)
Screw Pack
Backcheck Valve Power Adjustment Shaft
Latch Valve
Sweep Valve
Closer Body
Regular Arm/Top
Jamb Shoe
Connecting Rod
Forearm
Screw
Main Arm
Closer Arm
NOTE: Architectural Cover CAN
NOT be used for doors swinging
over 120° using parallel mount.
1618A Parallel
Arm Bracket
Cover Clips
Cover Screw
Cover Screws
Metal Cover
Standard With
8500M Series
8400M Cover
Cover Screw
Cover Screws
Standoffs
Architectural Metal Cover
Standard With 8500MA Series
8400MA Cover
Pinion Cap (1639)
Insert Cutouts
Cover
Insert
Standoff
Standoff
Architectural Plastic Cover
Standard With 8500A Series
8400A Cover
Cover
Insert
Insert Cutouts
Full Cover
Standard With 8500P Series
8400P Cover
Narrow Cover
Standard With 8300 Series
8200P Cover

Copyright © 2004, 2017 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2206-020 Rev 2 (09-17)
12
7
+
-
4
5
2
3
Non Hold Open Door Closers — Regular Arm
Door/Wall/Hardware/Jamb
*
conditions permitting
Right Hand Shown
Inches
(mm)
8000 Series
Pinion Cap or Optional Cover
Opening
To 100°
101° to 130°
131° to *180°
7-1/2
(191)
6
(152)
4-1/2
(114)
Dimension "A"
5-1/2
(140)
1-3/4
(44)
12
(305)
1-1/8
(29)
A
1-1/4
(32) 3/4
(19)
Spring Power Adjust
(If Necessary)
G
For
8500 Architectural
Cover Only
HOptional
A
F
90°
E
C
L
Y
S
Z
R
B
D
or
(2)
Mark and Drill Holes
Installation Sequence
H
Optional
Optional
Covers
1
Parts
8300 Series
Screw pinion cap onto pinion shaft by
hand or with a Phillips screw driver -
DO NOT OVER TIGTHEN.
Clips for metal
covers 8500M
Latch
Sweep
+
-
+
-
6
Backcheck
Caution:
Don't completely
close valve
!
Optional 8500M
Metal Cover Installation
2 Cover
Screws
8400M Cover
2 Clips for metal
covers 8500M
+
-

Copyright © 2004, 2017 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2206-020 Rev 2 (09-17)
13
6
3
2
Spring Power Adjust
(If Necessary)
1
8000 Series
Backcheck
Door/Wall/Hardware/Jamb
*
conditions permitting
Inches
(mm)
Parts
Caution:
Don't completely
close valve
A longer connecting
rod, 7701-1A, is
required for reveals
greater than 3" (76)
or
Pinion Cap
or Optional Cover
Optional
Covers
Reveal
Opening
To 100°
101° to 130°
131° to *180°
7-1/2
(191)
6
(152)
4-1/2
(114)
Dimension "A"
Right Hand Shown
5
Latch
+
-
Non Hold Open Door Closers — Top Jamb Arm
12
(305)
A
3/4
(19)
1/2
(13)
5-1/2
(140)
1-7/8
(38)
1-3/4
(44) C
L
Top of
Frame
For
8500 Architectural
Cover Only
H
Optional
+
-
Installation Sequence
D
A
B
C
L
Y
S
Z
R
E
90°
F
Mark and Drill Holes
!
8300 Series
Screw pinion cap onto pinion shaft
by hand or with a Phillips screw
driver - DO NOT OVER TIGHTEN.
Clips for metal
covers 8500M
A
B
E
90°
4
Sweep
+
-
8400M Cover
2 Clips for metal
covers 8500M
2 Cover
Screws
Optional 8500M
Metal Cover Installation 7
+
-
G
H
OptionalOptional
(2)

Copyright © 2004, 2017 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2206-020 Rev 2 (09-17)
14
2
1
5
3
D
46
8000 Series
Non Hold Open Door Closers — Parallel Arm
Door/Wall/Hardware/Jamb
*
conditions permitting.
8500A and 8500MA Series
cannot be installed
for this door opening range.
R
o
t
a
t
e
Door
Opening
To 120°
121° to 180°
*
A
9-1/2
(241)
7
(178)
B
3-3/4
(95)
1-1/4
(32)
Close Valves
Latch
Sweep
+
+
3-1/2
(89)
3/4
(19) 12
(305)
Top of
Door
Inches
(mm)
Frame
B
C
L
1/2
(13)
7/16
(11)
2
(51)
2-3/4
(70) 3/8
(10)
A
Remove Arm
from Spindle
Place Arm on
Spindle
Mark and Drill Holes
Install Closer and Bracket Preload Closer
Installation Sequence
Right Hand Shown
H
Optional
A
B
E
C
1-1/2”
F
G
Parts
Optional
Cover
Clips for metal
covers 8500M

Copyright © 2004, 2017 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2206-020 Rev 2 (09-17)
15
14
7 98
8000 Series
Non Hold Open Door Closers — Parallel Arm
11
10
Spring Power Adjust
(If necessary)
(2)
Assemble Arm
Arm Screw
Pinion Cap
or Optional Cover
L
Y
S
Z
R
L
Y
S
Z
R
Left Hand
Door
Right Hand
Door
or
B
A
Flat
Flat
Open Valves
Caution:
Don't remove
valves
Latch
Sweep
!
8300 Series
Screw pinion cap onto
pinion shaft by hand or
with a Phillips screw driver
- DO NOT OVER TIGHTEN.
12
13
Latch
Sweep
+
-
+
-
Backcheck
Caution:
Don't completely
close valve
+
-
!
2 Clips for metal
covers 8500M
2 Cover
Screws
Optional 8500M
Metal Cover Installation
8400M Cover
15
1-1/2
(38)
+
-
(Use 5/16" socket or adjustable wrench
for this Adjustment)
or

Copyright © 2004, 2017 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2206-020 Rev 2 (09-17)
16
ASSA ABLOY
8000 Series
CLOSED
70°
10°
Spring Power Adjust
Adjustment Chart
(8301 & 8501 Only)
EXTERIOR
INTERIOR
Regular Arm
Top Jamb
Regular Arm
Top Jamb
Parallel Arm
Parallel Arm
FULL 360° TURNS OF
5/16 POWER
ADJUSTMENT WRENCH
8100/8300/8500
DOOR
TYPE
OF
INST. *32"
(0.85M)
36"
(0.90M)
42"
(1.00M)
48"
(1.20M)
5811 13
7 10 13 16
710 13 16
912 15 18
20 FULL (360°) TURNS MAXIMUM AVAILABLE
*
MAXIMUM DOOR SIZE
Number of Turns Required
(Use 1/8" Hex Wrench for these Adjustments)
Arm Placement in Shoe
or
or
7-1/2 % stronger
7-1/2 % weaker
-
+
Backcheck
+
-
Latch
+
-
Sweep
+
-
Closer is shipped set at mid range setting = 10 turns
Adjust Closing Speed Time to between 3 to 7 seconds from 90°.
Use of the door by handicapped, elderly or small children may
require greater closing time.
!
The closing force for series 8301 & 8501 door closers is adjustable
from a size 1 to a size 6, as outlined in ANSI Standard A156.4.
When these series of door closers are installed and adjusted to
conform to ADA reduced opening force requirements (5 lbs max.) for
interior doors, they may not have adequate closing force to reliably
close and latch the door. Power adjustments charted on this page are
recommended where possible, to ensure proper door control.
By law the Americans with
Disabilities Act (ADA) may
require that door closer
installation comply with
accessability guidelines.
!
Delayed Action
(Optional)
+
-
+
-
To identify your model:
Closer Size
Mfg.
Date
1FA
Blank = 8301/8501
2 = 8302/8502
3 = 8303/8503
4 = 8304/8504
5 = 8305/8505
6 = 8306/8506
3
(Use 5/16” Socket or
Adjustable Wrench for
this Adjustment)
3000 Highway 74 East • Monroe, NC 28112
Tel: [phone] Ext. 4706 • Fax: [phone]
www. no r to ndoorcontrols. co m