Azbil SLPC1F User manual

Thank you for purchasing this Azbil
Corporation product.
This manual contains information for
ensuring the correct use of the smart
loader package.
Those designing, configuring, or
maintaining equipment that uses
this product should first read and
understand this manual. It provides
necessary information not only for
initial setup, but also for changing of
settings, troubleshooting, etc. Be sure
to keep it nearby for handy reference.
User’s Manual for Detailed
Functions of Smart Loader
Package
Model SLPC1F
for Single Loop Controller
Model C1M
No. CP-SP-1463E

NOTICE
Please make sure that this manual is available to the user of the product.
Unauthorized duplication of this user’s manual in part or in whole is
forbidden. The information and specifications in this manual are subject to
change without notice.
Considerable effort has been made to ensure that this manual is complete
and accurate, but if you should find an omission or error, please contact us.
In no event is Azbil Corporation liable to anyone for any indirect, special, or
consequential damages as a result of using this product.
© 2022 Azbil Corporation. All Rights Reserved.
Do not apply too much force when connecting the loader plug. Doing so might damage the
instrument.
Handling Precautions
• Application of excessive force to the loader plug might cause communications
failure. If this happens, reconnect the loader plug correctly.
IMPORTANT

i
Conventions Used in This Manual
The safety precautions explained below aim to prevent injury to you and others, and to prevent property damage.
WARNING Warnings are indicated when mishandling this product may
result in death or serious injury.
CAUTION Cautions are indicated when mishandling this product may
result in minor injury or property damage only.
In describing the product, this manual uses the icons and conventions listed below.
Indicates that caution is required in handling.
The indicated action is prohibited.
Be sure to follow the indicated instructions.
Handling Precautions:
Information to be aware of when handling.
Note: Indicates information that may be useful.
: Indicates an item or page to which the user may refer.
(1), (2), (3): Steps in a sequence or parts of a figure, etc.
>> : Indicates the result of an operation, or the status after the operation.

ii
UNPACKING
When unpacking the product, please do the following.
1. Check the model number to make sure you received the correct product.
2. Check for any obvious damage.
3. Check the contents of the package against the packing list to make sure that all items are included.
Items included in the package are shown below.
Handle model SLP-C1F and its accessories with care to prevent damage or loss of parts.
If there is any problem with your order, please contact your dealer promptly.
Name Model No. Qty Remarks
Installation disk SLP-C1F 1 The media for installing SLP-
C1F.
USB loader cable 8141177-001 1 The dedicated cable for
connecting C1M and a PC.
(Included in SLP-C1FJA0.)
User’s Manual CP-UM-5986JEC 1 The manual for installing SLP-
C1F.
Software License Agreement
Software License Agreement
CP-UM-5985JE 1 The license agreement for
using SLP-C1F. Please read it
carefully before installation.

iii
There are five different manuals related to the model C1M Single Loop Controller (hereafter “this device”).
Read them as necessary for your specific requirements.
If you do not have a manual you require, please contact us or your dealer.
Alternatively, you can download the necessary manuals from https://www.azbil.com.
User’s Manual for Detailed Functions of Smart Loader Package Model SLPC1F for
Single Loop Controller Model C1M
Document No. CP-SP-1463E
This manual.
This manual describes the software used on a PC to configure model C1M. Those
designing or setting up equipment that uses model C1M should read this manual. The
manual describes installation of the software into a PC, operation of the PC, various
functions, and setup procedures.
Smart Loader Package Model SLP-C1F Installation Manual
Document No. CP-UM-5986JEC
This manual is supplied with the product. It has descriptions in Japanese,
English, and Chinese. Personnel in charge of the design or manufacture of
equipment that incorporates this device should read this manual thoroughly.
This manual covers safety precautions, installation, wiring, main specifications,
and parameters of this device. For further information about operation, refer to
the user’s manual for installation and configuration.
Single Loop Controller Model C1M User’s Manual for Installation and
Configuration
Document No. CP-SP-1448E
This manual describes the hardware and all functions of this device. Personnel
in charge of the design, manufacture, operation, or maintenance of equipment
that incorporates this device, or those in charge of communication software for
equipment that uses this device’s communication functions, should read this
manual thoroughly.
This manual also describes the installation, wiring, connections for
communication, functions and settings of this device, operating procedures,
communication with a master station (PC, etc.), communication addresses,
troubleshooting, and detailed specifications.
Single Loop Controller Model C1M User’s Manual
Document No. CP-UM-5964JEC
This manual is supplied with the product. It has descriptions in Japanese, English
and Chinese. Personnel in charge of the design or manufacture of equipment
that incorporates this device should read this manual thoroughly. This manual
covers safety precautions, installation, wiring, main specifications, and
parameters of this device. For further information about operation, refer to the
user’s manual for installation and configuration.
The Role of This Manual

iv
CP-SP-1450E
Quick Reference Guide for Model C1M
Quick Reference Guide for Model C1M Document No. CP-SP-1450E
For those using this device for the first time or for operators on the work site, this
guide serves as a reference when specifying parameters.
Key operations, menu flowcharts and parameter settings are described with color
illustrations.
Organization of the Manual
This manual is organized as shown below.
Chapter 1 Introduction
Be sure to read this chapter before you start using this software.
Describes the required PC operating environment and briefly introduces the
features of the software.
Chapter 2 Installing, Starting, and Exiting the Loader
Tells how to install, start and quit the software.
Chapter 3 Setup
Tells how to configure settings.
Chapter 4 Monitoring
Discusses the settings and screens for monitoring the status of operation.
Chapter 5 Adjusting PID Values
Describes the PID Simulator support software for adjusting PID values and tells
how to adjust the PID values.
Chapter 6 Troubleshooting
Error messages and remedies

v
Conventions Used in This Manual
UNPACKING
The Role of This Manual
Organization of the Manual
Chapter 1. Introduction 1-1
1 - 1 Overview 1-1
 Functions of the loader 1-1
1 - 2 System Requirements 1-2
 Hardware 1-2
 Hardware configuration 1-3
Chapter 2. Installing, Starting, and Exiting the Loader 2-1
2 - 1 Installing the Loader 2-1
 Installation procedure 2-1
2 - 2 Installing the Device Driver for the USB Loader Cable 2-5
 Installing the USB loader cable device driver 2-5
 Handling precautions for uses other than SLP-C1F 2-8
 Uninstalling the device driver 2-9
2 - 3 Starting and Exiting the Loader 2-11
 Starting the loader 2-11
 Exiting the loader 2-11
Chapter 3. Setup 3-1
3 - 1 Setup Function 3-1
 Overview 3-1
 Flowchart for setup 3-1
 Screen explanations 3-1
3 - 2 Setting Method 3-4
Chapter 4. Monitoring 4-1
4 - 1 Monitoring Function 4-1
 Overview 4-1
 Screen explanations 4-2
4 - 2 Method of Operation 4-6
 How to operate the Numeric Monitor screen 4-6
 How to operate the Trend Monitor 4-9
Contents

vi
Chapter 5. Adjusting PID Values 5-1
5 - 1 What Is the PID Simulator? 5-1
 Overview 5-1
 Precautions 5-2
 Screen explanations 5-2
 Adjustment procedure 5-10
5 - 2 Functions of the PID Simulator 5-11
 Modeling wizard 5-11
 Auto tuning 5-16
 Memo 5-17
 Graph adjustment 5-19
 Loading/saving parameters 5-20
5 - 3 Data Sampling Method 5-21
 Overview 5-21
 Step 1: Choose a default process variable (PV) and set point 5-22
 Step 2: Stabilize the process variable (PV) and manipulated variable (MV) 5-23
 Step 3: Start data sampling 5-26
 Step 4: Start step response 5-26
 Step 5: End data sampling 5-27
 Step 6: Save the sampled data 5-28
5 - 4 When PID Adjustment is Unsuccessful 5-29
 Problems with adjustment or PID control simulation 5-29
 Problems with the PID simulator operation 5-30
Chapter 6. Troubleshooting 6-1
6 - 1 Error Messages and Countermeasures 6-1
 Error messages during communication 6-1
 Error messages during file operations 6-1
 Error messages while using the Trend Monitor 6-1
 Error messages while setting up PLC link communication 6-2
6 - 2 Other Troubleshooting 6-3

1-1
Chapter 1. Introduction
1 - 1 Overview
This software, model No. SLP-C1F (hereafter called “the loader”), is an engineering tool equipped not only with the
basic functions for configuring and monitoring the C1M single loop controller, but also with a PID Simulator for
improving controllability.
The loader is a software package that runs on a PC with the Microsoft Windows 10 operating system.
Note
• Install the loader on a PC by following Installation procedure (p.2-1).
 Functions of the loader
The loader has the following functions:
• Setup
• Monitoring
• Calibration and checking
• PID Simulator
z Setup
This function is for setting the required controller parameters on the PC and
writing (transferring) them to the controller. For details, refer to the following.
Chapter 3. Setup
z Monitoring
After writing the setup parameters to the controller, the user can do a trial run and
change control constants, tune the controller, switch modes (RUN/READY, AUTO/
MANUAL, etc.), and check the status of operation and of alarms.
The operating status can also be checked and collected on the Trend screen, and
collected data can be output in CSV format so that it can be used in third-party
spreadsheet software such as Microsoft Excel. For details, refer to the following.
Chapter 4. Monitoring
z Calibration and checking
This function is used to calibrate and check controller input.
For details on the calibration/inspection function, refer to the following.
Single Loop Controller Model C1M User’s Manual for Installation and
Configuration (CP-SP-1448E).
z PID Simulator
The PID Simulator assists in adjusting PID values using Azbil’s proprietary
simulation technology.
Chapter 5. Adjusting PID Values (p.5-1)

1-2
Chapter 1. Introduction
The following system environment is required to use the loader.
 Hardware
Item Description
Hardware CPU Windows PC with an Intel CPU
Recommended: 1.5 GHz or more. Minimum: 1 GHz
Operating system Windows 10
Memory (RAM) Recommended: 4 GB or more. Minimum: 2 GB
Hard disk Recommended free space: 20 GB or more. Minimum: 10 GB
Monitor resolution 1366 × 768 or higher
USB ports 1 or more
(It is necessary to connect to the C1M with a USB loader cable
(81441177-001))
Optical drive Used to install the software from the installation media (CD-ROM).
Input devices Keyboard, mouse, and touchpad
Other PDF Adobe Acrobat DC or a later version
Handling Precautions
• Make sure that [Decimal symbol] has been set to“.”in [Control Panel] →
[Regional Settings] →[Number]. If it is set to some other character, the loader
program will not function correctly.
1 - 2 System Requirements