Ballard Designs Casa Florentina Louis XVI Armoire MA200 User manual

PRODUCT NAME: Louis XVI Armoire
ITEM NUMBER: MA200
ASSEMBLED DIMENSIONS: 77 3/4”H x 43”W x 21 1/2”D
PRODUCT NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 3-18-2020
MADE IN ITALY
Page 1 of 5
Customer Service : 800-367-2810
Online: www.ballarddesigns.com

Page 2 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Ltr.
D
E
1
1
Qty. Components
TOOLS NEEDED:
- Phillips Screwdriver
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
NOTE: To avoid accidentally
discarding small parts or hardware,
retain all carton contents until
assembly and installation are complete.
Assemble in location for intended use.
Ltr.
A 2
B 12
Qty. Hardware Included
C 2
Keys (spare inlcuded)
Shelf Supports
Wall Anchoring
(Anti-tip) Kits
See Page 5
F
G
4
3
Armoire (D)
Feet (E)
Shelves (F)
Hanging Rod (G)
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
ANCHORING HARDWARE INCLUDED

Page 3 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(E)
(D)
STEP 2: Determine location for each Shelf (F) then insert Shelf Supports (B) into corresponding
pre-drilled holes. Carefully set each Shelf level upon Supports with notched side oriented to back of
Armoire.
(B)
(F)
Fixed Shelf
(not adjustable)
Front
Back
STEP 1: Onto a clean, level, padded surface, place Armoire (D) on its back. Insert Feet (E) into t-nuts
embedded in corners. Hand tighten until fully secured. Do not over tighten.
CAUTION: Prevent damage. When turning Armoire upright
DO NOT PLACE UNEVEN PRESSURE ON FEET.
Assemble in location for intended use.

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 4 of 5
Cleaning & Care
Do not use alcohol based products or spray polisher as finish damage may result.
Periodically dust with a soft, dry cloth.
(G)
Set the Hanging Rod (F) into the Brackets in the Armoire.
(E)
STEP 3: Set Hanging Rod (G) into Brackets as illustrated below.
STEP 4: If doors are misaligned or Armoire requires leveling, carefully lift corner and turn Feet (E).

Installation:
Ltr.
A2
Small Screw
Retention Belt
Qty. Hardware Included
B2
Large Screw
C4 Bracket
D2
WALL ANCHORING HARDWARE (ANTI-TIP)
1. Place furniture against wall at desired location then locate and mark a Wall Stud behind unit.
2. Corresponding to Stud location, attach one Bracket (C) to back of unit using Small Screw (B).
3. To keep hardware out of view after installation, attach remaining Bracket (C) INTO WALL STUD
with Large Screw (A) 2 inches below Bracket attached to back of unit.
4. Move unit into place, align Brackets then connect both using Retention Belt (D).
5. Confirm Belt is securely laced and locked.
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
W
A
L
L
S
TUD
WALL BRACKET MUST BE ATTACHED TO WALL STUD
(A)
(B)
(C)
(D)
Page 5 of 5
R
e
presen
t
a
tiv
e
Fu
r
nitu
r
e
I
tem
Customer Service: 800-367-2810
Online: www.ballarddesigns.com